Sony NWZ-E435F / NWZ-E436F / NWZ-E436FK / NWZ-E438F Service Manual ▷ View online
NWZ-E435F/E436F/E436FK/E438F
9
3-5. MINI JACK
Note:
This illustration sees the set from battery side.
3-6. MAIN BOARD, ESCUTCHEON
Note 1:
This illustration sees the set from battery side.
protection sheet
(HP)
HP printed wirinig board
(J6)
screw
(PTP1.4)
holder (HP)
sheet (JACK) adhesive
Remove three solders.
mini jack
Note: Sheet (JACK) adhesive cannot be reused.
R gasket (CPU)
LCD flexible board
(J5)
battery connector
(J3)
RH escutcheon
RG MAIN board
Remove two solders.
claw
static shield sheet
RE W (WMPORT) sheet
protection sheet (wire)
RB condustive sheet
RT Turn over the protection sheet (wire).
HP printed wirinig board
(J6)
HP jack block
NWZ-E435F/E436F/E436FK/E438F
10
3-7. LIQUID CRYSTAL DISPLAY PANEL
button (VOL)
RT liquid crystal
display panel
two sheet (LCD) adhesives
R two LCD sheets (light)
two LCD spacers
two screws
(M1.4)
Lift the LCD and remove it.
cu (ornament) sheet
cu (ornament L) sheet
two screws
(M1.4)
RB protection sheet (LCD)
claw
claw
Note 1: Take care not to damage the liquid crystal display panel
by applying an excessive force.
Note 2: Sheet (LCD) adhesive cannot be reused.
3-8. SVX VOL SW ASSY
button (VOL)
two screws
(M1.4)
cu (ornament) sheet
cu (ornament L) sheet
two screws
(M1.4)
claw
claw
protection sheet
(VOL
wire)
RT SVX VOL SW assy
protection sheet (VOLFPC)
RB wire
R Remove two solders.
NWZ-E435F/E436F/E436FK/E438F
11
SECTION 4
TEST MODE
Note: Information on the test mode must correspond in enough
security. When the leakage has been revealed by any
chance, the source of information is specifi ed.
chance, the source of information is specifi ed.
1. SETTING THE TEST MODE
Note: Perform the test mode in the state of 3.6 V or more in the battery
voltage.
Setting method:
1. Turn the power on.
2. Press the [BACK] key for 1.5 seconds or more, the home menu
1. Turn the power on.
2. Press the [BACK] key for 1.5 seconds or more, the home menu
is displayed.
3. Slide the [HOLD] key to set the hold on.
4. While pressing the [OPTION] key, press the key as following
4. While pressing the [OPTION] key, press the key as following
order.
[
v
]
→ [
u
]
→ [
B
]
→ [
u
]
→ [
V
]
→ [
u
]
→ [
b
]
→ [
u
]
→
[
v
]
→ [
u
]
→ [BACK] → [
u
]
5. Enter the test mode.
Note: The destination setting and sound pressure regulation setting cannot
be executed by this test mode.
2. RELEASING THE TEST MODE
1. Display the major item selection screen.
2. Press the [
1. Display the major item selection screen.
2. Press the [
v
]/[
V
] key to select the “EXIT”, and press the [
B
]
key to select the “SURE?”.
3. Press
the
[
u
] key, TURN the POWER off and release the test
mode.
3. CONFIGURATION OF THE TEST MODE
<>
key
Major item
Major item switching:
<>/<>
key
<#"$,>
key
Minor item
Finish
or
Result
Start
Automatic
V
<>
key
<>
key
#
C
W 7
Minor item switching:
<>/<>
key
W 7
4. OPERATION OF THE TEST MODE
4-1. Power
4-1. Power
liquid crystal display
MPTAPP MENU
POWER
VCHK
AUDIO
ACHK
VIDEO
DSVCHK
OTHER
CHGCHK
CLESTE
BATTCHK
DAC
FM
SHUTDN
EXIT
FM
SHUTDN
EXIT
4-1-1. Power supply voltage check
This mode is used in case power supply voltage in the state where
all power supply lines are starting is checked.
This mode is used in case power supply voltage in the state where
all power supply lines are starting is checked.
Checking method:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
v
]/[
V
] key to select the “POWER”, and press the
[
B
] key to enter the minor item.
3. Press the [
v
]/[
V
] key to select the “VCHK”.
4. Press the [
u
] key, all power supply lines are started.
liquid crystal display
VCHK
VDDIO : X.XXXV
VDDA : X.XXXV
VDDD : X.XXXV
In this state, the power supply voltage of each power supply
line can be confi rmed by measuring the voltage.
line can be confi rmed by measuring the voltage.
5. Press the [BACK] key, return to minor item selection screen.
4-1-2. Consumption current (audio playback) check
This mode is used in case consumption current (audio playback)
is checked in the state where “1 kHz 0 dBs L-ch/R-ch VOLUME:
15” audio signal is output.
This mode is used in case consumption current (audio playback)
is checked in the state where “1 kHz 0 dBs L-ch/R-ch VOLUME:
15” audio signal is output.
Checking method:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
v
]/[
V
] key to select the “POWER”, and press the
[
B
] key to enter the minor item.
3. Press the [
v
]/[
V
] key to select the “ACHK”.
4. Press the [
u
] key, “1 kHz 0 dBs L-ch/R-ch VOLUME: 15”
audio signal is output.
liquid crystal display
ACHK
1kHz 0dBs L/Rch
HPOUT [ VOL 15 ]
BL ON
5. In this state, each time the [OPTION] key is pressed, LCD
back light on /off switch is performed.
6. Press the [BACK] key, return to minor item selection screen.
NWZ-E435F/E436F/E436FK/E438F
12
4-1-3. Standby current check
This mode is used in case standby current is checked.
This mode is used in case standby current is checked.
Checking method:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
v
]/[
V
] key to select the “POWER”, and press the
[
B
] key to enter the minor item.
3. Press the [
v
]/[
V
] key to select the “DSVCHK”.
4. Press the [
u
] key, enter the state of the deep sleep.
5. Press the [BACK] key, release the state of the deep sleep, and
return to minor item selection screen.
4-1-4. Charge current check
This mode is used in case charge current is checked.
This mode is used in case charge current is checked.
Checking method:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
v
]/[
V
] key to select the “POWER”, and press the
[
B
] key to enter the minor item.
3. Press the [
v
]/[
V
] key to select the “CHGCHK”.
4. Press the [
u
] key, the change setting is displayed.
liquid crystal display
CHGCHK
AC
AC
5. In this state, each time the [OPTION] key is pressed, the port
setting for the charge is changed as shown in the table below.
6. Press the [BACK] key, return to minor item selection screen.
4-1-5. Battery voltage detection check
This mode is used in case battery voltage is checked.
This mode is used in case battery voltage is checked.
Checking method:
1. Enter the test mode.
2. Press the [
1. Enter the test mode.
2. Press the [
v
]/[
V
] key to select the “POWER”, and press the
[
B
] key to enter the minor item.
3. Press the [
v
]/[
V
] key to select the “BATTCHK”.
4. Press the [
u
] key, the battery voltage is displayed.
When the battery voltage cannot be confi rmed, “ERROR” is
displayed.
displayed.
liquid crystal display
BATTCHK
Battely Voltage
X.XXXV
X.XXXV: Battery voltage
5. Press the [BACK] key, return to minor item selection screen.
4-2. Audio
While playing the audio track, it’s in a repeat state. If [BACK] key
is pressed, it’s stopped.
Press the [VOL +] key to switch the HP/LINE.
While playing the audio track, it’s in a repeat state. If [BACK] key
is pressed, it’s stopped.
Press the [VOL +] key to switch the HP/LINE.
liquid crystal display
MPTAPP MENU
POWER
OUTPUT
AUDIO
SN
VIDEO
F1
OTHER
F2
CLESTE
SEPLR
DAC
SEPRL
FM
MAXOUT
SHUTDN
NMLZR
EXIT
SPCHK
Port control
Display
CHG_XCHGEN
CHG_PEN1
CHG_PEN2
AC
L
H
H
USB500
L
H
H
USB100
L
H
L
Click on the first or last page to see other NWZ-E435F / NWZ-E436F / NWZ-E436FK / NWZ-E438F service manuals if exist.