Sony NWZ-E435F / NWZ-E436F / NWZ-E436FK / NWZ-E438F Service Manual ▷ View online
NWZ-E435F/E436F/E436FK/E438F
5
METHOD OF JUDGING RIGHT AND WRONG OF
PARTS RELATED TO SWITCH
In this set, only a part of parts that relate to the switch are sup-
plied.
The right and wrong of the switch can be judged by the following
two methods.
PARTS RELATED TO SWITCH
In this set, only a part of parts that relate to the switch are sup-
plied.
The right and wrong of the switch can be judged by the following
two methods.
1. Judgment From The Test Mode
Judge the right and wrong of the switch referring to “4-4-3. Key
check” (page 16).
Judge the right and wrong of the switch referring to “4-4-3. Key
check” (page 16).
2. Judgment from the voltage measurement
Judge the right and wrong of the switch by the voltage measure-
ment with a test point.
Judge the right and wrong of the switch by the voltage measure-
ment with a test point.
2-1. RESET key (SW1)
Connection:
When the voltage value is below, RESET key (SW1) is normal.
• RESET key (SW1) is pressed
• RESET key (SW1) is pressed
: 0 V
• RESET key (SW1) is not pressed : 3.1 V
2-2. HOLD switch (SW610)
Connection:
When the voltage value is below, HOLD switch (SW610) is nor-
mal.
• HOLD switch (SW610) is turned on : 0 V
• HOLD switch (SW610) is turned off : 3.1 V
mal.
• HOLD switch (SW610) is turned on : 0 V
• HOLD switch (SW610) is turned off : 3.1 V
2-3. [u]/[B]/[b]/[v]/[V]/[BACK]/[OPTION]/[VOL +]/[VOL –]
keys
Connection:
When the voltage value is below, [u]/[B]/[b]/[v]/[V]/[BACK]
[OPTION]/[VOL +]/[VOL –] keys are normal.
• Keys are not pressed
[OPTION]/[VOL +]/[VOL –] keys are normal.
• Keys are not pressed
: 3.1 V
• [u] key (SW605) is pressed
: 1.35 to 1.53 V
• [B] key (SW606) is pressed
: 1.71 to 1.85 V
• [b] key (SW607) is pressed
: 2.03 to 2.15 V
• [v] key (SW608) is pressed
: 2.36 to 2.46 V
• [V] key (SW609) is pressed
: 2.69 to 2.85 V
• [BACK] key (SW604) is pressed
: 1.09 to 1.20 V
• [VOL –] key is pressed
: 0.12 to 0.40 V
• [VOL +] key was pushed
: 0.68 to 0.95 V
+
–
–
digital voltmeter
R1
T8 (FM_GND)
+
–
–
digital voltmeter
J601 pin
J601 pin
J601 pin
+
–
–
digital voltmeter
D2 (anode)
J4 pin
2-4. OPTION key (SW601)
Connection:
Connection:
When the voltage value is below, OPTION key (SW601) is nor-
mal.
• OPTION key (SW601) is pressed
mal.
• OPTION key (SW601) is pressed
: 0 V
• OPTION key (SW601) is not pressed : 3.1 V
Connection location:
J4
1
2
29
T8 (FM_GND)
R1
2
4
1
30
29
9
J601
30
D2
– MAIN Board (Side A) –
– MAIN Board (Side B) –
– KEY Board (Side B) –
+
–
–
digital voltmeter
J601 pin
J601 pin
J601 pin
Note: Refer to page 20 for the schematic diagram.
Refer to page 19 for the printed wiring boards.
NWZ-E435F/E436F/E436FK/E438F
6
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Parts and Controls
Front
BACK/HOME button*
1
Press to go up one list screen level, or
to return to the previous menu.
Press and hold the BACK/HOME
button to display the Home menu.
to return to the previous menu.
Press and hold the BACK/HOME
button to display the Home menu.
Headphone jack
For connecting the headphones.
Insert the plug until it clicks into
place. If the headphones are
connected improperly, the sound
from the headphones may not sound
right.
Insert the plug until it clicks into
place. If the headphones are
connected improperly, the sound
from the headphones may not sound
right.
WM-PORT jack
Use this jack to connect the supplied
USB cable, or optional peripheral
devices, such as supported
accessories for the WM-PORT.
USB cable, or optional peripheral
devices, such as supported
accessories for the WM-PORT.
5-way button*
2
Starts playback and enables
navigation of the player’s on-screen
menus.
navigation of the player’s on-screen
menus.
Display
The display may vary, depending on
functions.
functions.
VOL +*
2
/– button
Adjusts the volume.
HOLD switch
You can protect the player against
accidental operation by using the
HOLD switch when carrying it. By
sliding the HOLD switch in the
direction of the arrow #, all
operation buttons are disabled. If you
slide the HOLD switch to the
opposite position, the HOLD
function is released.
accidental operation by using the
HOLD switch when carrying it. By
sliding the HOLD switch in the
direction of the arrow #, all
operation buttons are disabled. If you
slide the HOLD switch to the
opposite position, the HOLD
function is released.
OPTION/PWROFF button*
1
Displays the option menu.
If you press and hold the OPTION/
PWR OFF button, the screen turns
off and the player enters standby
mode. If you press any button while
If you press and hold the OPTION/
PWR OFF button, the screen turns
off and the player enters standby
mode. If you press any button while
the player is in standby mode, the
“Now Playing” screen, etc., appears
and the player is ready for operation.
Furthermore, if you leave the player
in standby mode for about 4 hours,
the player turns completely off
automatically. If you press any button
when the player is turned off, the
start up screen appears first, then the
“Now Playing” screen appears.
“Now Playing” screen, etc., appears
and the player is ready for operation.
Furthermore, if you leave the player
in standby mode for about 4 hours,
the player turns completely off
automatically. If you press any button
when the player is turned off, the
start up screen appears first, then the
“Now Playing” screen appears.
Note
• The player consumes battery power
very slightly even when it is in standby
mode. Therefore, the player might
turn completely off in a short time,
depending on the power remaining in
the battery.
mode. Therefore, the player might
turn completely off in a short time,
depending on the power remaining in
the battery.
Rear
RESET button
Resets the player when you press the
RESET button with a small pin, etc.
RESET button with a small pin, etc.
*
1
Functions marked with
on the
player are activated if you press and hold
the corresponding buttons.
the corresponding buttons.
*
2
There are tactile dots. Use them to help
with button operations.
with button operations.
NWZ-E435F/E436F/E436FK/E438F
7
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
Note: Follow the disassembly procedure in the numerical order given.
3-2. REAR CASE
Note:
This illustration sees the set from rear side.
SET
3-5
MINI JACK
(Page
9)
3-6. MAIN BOARD,
ESCUTCHEON
(Page
ESCUTCHEON
(Page
9)
3-4. BATTERY (N) ASSY
(Page
(Page
8)
3-2. REAR CASE
(Page
(Page
7)
3-8. SVX VOL SW ASSY
(Page 10)
3-7. LIQUID CRYSTAL
DISPLAY
DISPLAY
PANEL
(Page 10)
3-3. SVX FRONT CASE ASSY,
KEY BOARD
(Page
8)
two screws
(PTP1.4)
two claws
two claws
two claws
claw
rear case
NWZ-E435F/E436F/E436FK/E438F
8
3-3. SVX FRONT CASE ASSY, KEY BOARD
two screws
(B1.4)
two claws
claw
claw
claw
claw
SVX front case assy
button (front)
connector
(J601)
gasket (CPU)
KEY board
Note: On installation of knob (hold), adjust
the position of switch (SW610) and
knob
(hold).
switch (SW610)
knob (hold)
3-4. BATTERY (N) ASSY
battery (N) assy
static shield sheet
battery connector
(J3)
batt sheet
gasket (volume)
sheet (BATT) adhesive
protection sheet
(battery)
Turn over the protection sheet (wire).
Turn over the protection sheet (VOL wire).
Note 1: Take care not to damage the battery (N) assy by
applying an excessive force.
Note 2: Sheet (BATT) adhesive cannot be reused.
Click on the first or last page to see other NWZ-E435F / NWZ-E436F / NWZ-E436FK / NWZ-E438F service manuals if exist.