Sony NW-S21 / NW-S23 Service Manual ▷ View online
NW-S21/S23
5
Note:
Follow the disassembly procedure in the numerical order given.
3-2. CASE (REAR) SUB ASSY
•
This set can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW
SECTION 3
DISASSEMBLY
3-2. CASE (REAR) SUB ASSY
(Page 5)
3-4. MAIN BOARD
(Page 6)
3-5. DISPLAY BOARD
(Page 7)
3-3. CHASSIS (BATTERY CASE LID)
(Page 6)
SET
3
five claws
1
cover (play/stop) assy
adhesive sheet (cover P/S)
2
three screws (1.6
×
8)
4
case (rear) sub assy
NW-S21/S23
6
3-3. CHASSIS (BATTERY CASE LID)
3-4. MAIN BOARD
6
case cover assy
4
two claws
5
chassis (battery case lid)
3
two screws (B1.4)
1
Push the button (open).
2
Open the case cover assy.
1
connector (CN401)
2
main board
NW-S21/S23
7
3-5. DISPLAY BOARD
1
display board
8
NW-S21/S23
KEY CHECK MODE
Procedure:
1. Put a dry battery into the set and keep a battery lid open.
2. Turn on the [HOLD] switch, then while pressing
2. Turn on the [HOLD] switch, then while pressing
the
Nx
button and the [GROUP] button, close a battery lid
and power supply is turned on.
3. “256M 4.05.08 G07” is displayed on the liquid crystal display.
4. Turn off the [HOLD] switch.
5. Press the
4. Turn off the [HOLD] switch.
5. Press the
Nx
button.
6. “Check all keys” is displayed on the liquid crystal display and
key check mode is activated. Then, when each button is
pressed, it is displayed on liquid crystal display as follows.
pressed, it is displayed on liquid crystal display as follows.
•
[MENU] button:
“EL0: ON” or “EL0: OFF” (Liquid crystal display back light
“EL0: ON” or “EL0: OFF” (Liquid crystal display back light
(EL0 (blue)) turns on/off)
•
[GROUP] button:
“EL1: ON” or “EL1: OFF” (Liquid crystal display back light
“EL1: ON” or “EL1: OFF” (Liquid crystal display back light
(EL1 (green)) turns on/off)
•
+ > button:
“Parts: ON” (ACCESS LED turns on)
•
. – button:
“Parts: OFF” (ACCESS LED turns off)
•
VOLUME + button:
“Beep: ON” (BEEP turns on)
•
VOLUME – button:
“Beep: OFF” (BEEP turns off)
•
[REPEAT SOUND] button:
“Initialized” (Time, volume setting etc. turn to the factory
“Initialized” (Time, volume setting etc. turn to the factory
preset state. But the music data, files etc. in the memory are
not changed)
not changed)
Note:
The following check is performed at the end.
•
+ > button: (Only the state where the liquid crystal display
back light (EL1 (green)) turns on)
All liquid crystal display light up.
•
. – button:(Only the state where the liquid crystal display
back light (EL1 (green)) turns on)
All liquid crystal display go off.
7. All keys inputs are completed, then press the
Nx
button to
restart as usual.
SECTION 4
TEST MODE
Click on the first or last page to see other NW-S21 / NW-S23 service manuals if exist.