DOWNLOAD Sony MHC-NX1 / MHC-NX3AV / STR-NX1 / STR-NX3 Service Manual ↓ Size: 4.36 MB | Pages: 42 in PDF or view online for FREE

9

• Execute only if connected to the HTC-NX1.
This mode can be used for operation check of CD section and tape
deck section.
CD section and tape deck section work in parallel.
• If an error occurred:

The aging operation stops only an error occurred sections and
display then status.

• If no error occurs:

The aging operation continues repeatedly.

Procedure:
1. Set disc in DISC5 tray.
2. Load the tapes into the decks A and B respectively.
3. Press the 

[PLAY MODE]

 button to set the “ALL DISCS” mode,

and press the 

[REPEAT]

 button to “REPEAT” off.

4. Press the 

[CD]

 button to select the function “CD”.

5. Press three buttons of 

[ENTER]

 , 

[POWER SAVE/DEMO]

 ,

and 

[TUNER BAND]

 simultaneously.

6. The aging mode is activated, if the indicator of disc tray num-

ber on the liquid crystal display is blinking.

7. To release from the aging mode, press the

?

/

1

button to turn

the power OFF and operate the cold reset. (Refer to the “MC
Cold Reset”)

1. Display at the Aging Mode

• Display operating state of CD section and tape deck section al-

ternately.

• If an error occurred, stop display which that section.

2. CD Section

• Display at the aging mode is the same as the normal operation.
• The sequence during the aging mode is following as below.

Open the disc1 tray

Disc5 chucking

Disc5 TOC read

Disc5 play track1 for 2 seconds

Disc5 play last track for 2 seconds

• Display at an error occurred
1) Display of the error count
(1)

Press three buttons of 

[ENTER]

 , 

[POWER SAVE/DEMO]

 ,

and 

[GROOVE]

 simultaneously.

(2)

Display of the error count following as below.

Display

EMC

**

EDC

**

EMC

**

: The number of mechanical error.

EDC

**

: The number of no disc error after chucking the disc.

2) Display of mechanical error

Display

E

**

M##$$&&

**

: The number of mechanical error.(“00” is latest one)

(Press the 

[PLAY MODE]

 button to changes next error display)

## : Not used.
$$ : Loading error. (Second figure is not used)

D : The error in the midst of close at the except mechanical trouble.
E : The error in the midst of open at the except mechanical trouble.
C : The error in the midst of chuck up at the except mechanical

trouble.

F : The error in the midst of EX-open at the except mechanical

trouble.

&&: Loading error. (Second figure in not used)

1: The error in the midst of chuck up.
2: The error in the midst of chuck down.
3: Time up of EX-open
4: Time up of EX-close.

3) Display of no disc error

Display

E

**

D##$$&&

**

: The number of mechanical error.(“00” is latest one)

(Press the 

[REPEAT]

 button to changes next error display)

##:

01: Focus error
02: GFS error
03: Set up error

$$:

00: No disc error when does not chucking retry.
02: No disc error when chucking retry to completion.

&&: The state when judged no disc error. (Second figure is not used)

1: Stop
2: Set up
3: TOC read
4: Access
5: Play
6: Pause
7: Manual search (Play)
8: Manual search (Pause)

3. Tape Deck Section

10

3. Tape Deck Section

• The sequence during the aging mode is following as below.
• If an error occurred, stop display that step.

Rewind the tape A and B

“TAPE A AG-1”

Shut off

FWD play the tape A

“TAPE A AG-2”

2 minutes

Fast forward the tape A

“TAPE A AG-3”

Shut off or 20 seconds

REV play the tape A

“TAPE A AG-4”

2 minutes

Rewind the tape A

“TAPE A AG-5”

Shut off

FWD play the tape B

“TAPE B AG-2”

2 minutes

Fast forward the tape B

“TAPE B AG-3”

Shut off or 20 seconds

REV play the tape B

“TAPE A AG-4”

2 minutes

Rewind the tape B

“TAPE B AG-5”

Shut off

 “TAPE 

*

 AG-

*

” is display of each step.

11

11

Note on Printed Wiring Board:
•

X

: parts extracted from the component side.

•

Y

: parts extracted from the conductor side.

•

x

: parts mounted on the conductor side.

•

b

: Pattern from the side which enables seeing.

(The other layers' patterns are not indicated)
• Indication of transistor.

Note on Schematic Diagram:
• All capacitors are in µF unless otherwise noted.  pF: µµF

50 WV or less are not indicated except for electrolytics
and tantalums.

• All resistors are in 

Ω

 and 

1

/

4

 

W or less unless otherwise

specified.

•

f

: internal component.

•

2

: nonflammable resistor.

•

5

: fusible resistor.

•

C

: panel designation.

•

U

: B+ Line.

•

V

: B– Line.

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : TUNER (FM)

• Voltages are taken with a VOM (Input impedance 10 M

Ω

).

Voltage variations may be noted due to normal produc-
tion tolerances.

• Waveforms are taken with a oscilloscope.

Voltage variations may be noted due to normal produc-
tion tolerances.

• Circled numbers refer to waveforms.
• Signal path.

F

: TUNER (FM)

E

: TAPE PLAYBACK

G

: RECORD

J

: CD PLAY

N

: MIC INPUT

• Abbreviation

AUS

: Australian model

CND : Canadian model
JE

: Tourist model

KR

: Korean model

Note:
The components identi-
fied by mark 

0

 or dotted

line with mark 

0

 are criti-

cal for safety.
Replace only with part
number specified.

Note:
Les composants identifiés par
une marque 

0

 sont critiques

pour la sécurité.
Ne les remplacer que par une
pièce por tant le numéro
spécifié.

B

These are omitted.

C

E

Q

B

These are omitted.

C

E

Q

1

IC501 

q;

 (XCIN)

2

IC501 

qd

 (XOUT)

F01

R02

R01

LINE NF

LINE IN

REFERENCE

CURRENT

REFERENCE

CURRENT

RESET

BAND

PASS

FILTER

DET

17

RESET

18

F02

16

F03

15

F04

14

F05

13

F06

12

REC LEVEL

11

VCC

10

4

3

2

1

+

–

REC NF

REC IN

6

RESET C

7

BIAS C

8

GND

9

5

+

–

1.4 Vp-p

32.768 kHz

3 Vp-p

16 MHz

SUB TRANS board
(US, Canadian, AEP, UK)

TRANS board

BACK LIGHT board

PANEL baord

R board

PA board 

MAIN board

SURROUND AMP board
(NX3)

TUNER pack

MY

: Malaysia model

SP

: Singapore model

TH

: Thai model

12

12

(Page 13)

(Page

 14)

(Page

 17)

(Page

 19)