Sony ICF-CD555TV Service Manual ▷ View online
17
ICF-CD555TV
5-3-2. POSITION SET UP ADJUSTMENT
Check the B level of the waveform on the oscilloscope is 4.2
±
0.1 Vp-p and adjust the RV1551 so that the C level of the waveform
on the oscilloscope is –2.4
on the oscilloscope is –2.4
±
0.1 Vp-p.
5-4.
INVERTER HIGH VOLTAGE CHECK
Connection:
Checking Procedure:
Connect an oscilloscope to the TP1805 and TP1806 on the TV
board.
Connect an oscilloscope to the TP1805 and TP1806 on the TV
board.
5-4-1. HIGH VOLTAGE CHECK
Check that the reading of oscilloscope is 550
±
150 V (rms).
5-4-2. FREQUENCY CHECK
Check that the reading of oscilloscope is 70
±
3 kHz.
5-5.
OSD DOT CLOCK CHECK
Connection:
Adjusting Procedure:
1. Connect an frequency counter to the TP1554 on the TV board.
2. Check that the reading of frequency counter is 6.5
1. Connect an frequency counter to the TP1554 on the TV board.
2. Check that the reading of frequency counter is 6.5
±
0.2 MHz.
5-6.
NTSC SUB CARRIER CHECK
Connection:
Checking Procedure:
1. Connect an frequency counter to the TP1508 on the TV board.
2. Check that the reading of frequency counter is 3.579545
1. Connect an frequency counter to the TP1508 on the TV board.
2. Check that the reading of frequency counter is 3.579545
±
0.0001 MHz.
5-7.
VIDEO BUS ADJUSTMENT
Connection: (5-7-1 to 5-7-9)
Condition: (5-7-1 to 5-7-9)
Input the NTSC video signal (10 step (no burst)) (1 Vp-p 75
Input the NTSC video signal (10 step (no burst)) (1 Vp-p 75
Ω
) to
the INPUT VIDEO jack (JK301) on the MAIN board from NTSC
pattern generator.
pattern generator.
Adjusting Procedure:
1. Set the TV test mode (Refer to TV TEST MODE (See page
1. Set the TV test mode (Refer to TV TEST MODE (See page
12).
2. Press the
[TV MENU]
key to select “LOAD DEFAULT”, and
press the
[ENTER]
key to write initial values to the EEPROM.
Note:
It carries out, only when EEPROM (IC1451) is exchanged.
3. Press the
[TV MENU]
key to select “FOR FACTORY”, and
press the
[ENTER]
key to enter the adjustment mode.
4. If entering the adjustment mode, press the
[TV MENU]
key to
select item, and press the
[ENTER]
key to execute all
adjustment items mentioned below.
5-7-1. GAMMA 1 ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
.
/
>
keys so that the H level of the wave-
form on the oscilloscope is 2.1
±
0.1 Vp-p.
5-7-2. GAMMA 2 ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
.
/
>
keys so that the J level of the wave-
form on the oscilloscope is 3.0
±
0.1 Vp-p.
B
0V
C
+
–
–
TP1806
TP1805
set
osclloscope
(high resistance probe)
+
–
–
TP1403 (GND)
TP1554
set
frequency counter
(high impedance probe)
+
–
–
TP1403 (GND)
TP1508
set
frequency counter
(high impedance probe)
+
–
–
NTSC pattern
generator
TP1403 (GND)
TP1958 or
TP1959 or
TP1959 or
TP1960
set
osclloscope
INPUT VIDEO jack
(JK301)
H
0V
J
0V
18
ICF-CD555TV
5-7-7. B-SUB BRT (B-CH SUB BRIGHT) ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope of 1 step voltage to the TP1960 on
1. Connect an oscilloscope of 1 step voltage to the TP1960 on
the TV board.
2. Adjust the
.
/
>
keys so that the G level of the wave-
form on the oscilloscope is 1.0
± 0.1 Vp-p.
5-7-8. R-SUB CONT (R-CH SUB CONTRAST)
ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope of 10 step voltage to the TP1958 on
1. Connect an oscilloscope of 10 step voltage to the TP1958 on
the TV board.
2. Adjust the
.
/
>
keys so that the D level of the wave-
form on the oscilloscope is 3.25
± 0.1 Vp-p.
5-7-9. B-SUB CONT (B-CH SUB CONTRAST)
ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope of 10 step voltage to the TP1960 on
1. Connect an oscilloscope of 10 step voltage to the TP1960 on
the TV board.
2. Adjust the
.
/
>
keys so that the D level of the wave-
form on the oscilloscope is 3.25
± 0.1 Vp-p.
5-7-3. Y GAIN (LUMINANCE SIGNAL CONTRAST
LEVEL) ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
.
/
>
keys so that the D level of the wave-
form on the oscilloscope is 3.25
± 0.1 Vp-p.
5-7-4. BLACK LIMIT (BLACK LIMITER LEVEL)
ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
.
/
>
keys so that the E level of the wave-
form on the oscilloscope is 1.0
± 0.1 Vp-p.
5-7-5. WHITE LIMIT (WHITE LIMITER LEVEL)
ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
1. Connect an oscilloscope to the TP1959 on the TV board.
2. Adjust the
.
/
>
keys so that the F level of the wave-
form on the oscilloscope is 3.9
± 0.05 Vp-p.
5-7-6. R-SUB BRT (R-CH SUB BRIGHT) ADJUSTMENT
Adjusting Procedure:
1. Connect an oscilloscope of 1 step voltage to the TP1958 on
1. Connect an oscilloscope of 1 step voltage to the TP1958 on
the TV board.
2. Adjust the
.
/
>
keys so that the G level of the wave-
form on the oscilloscope is 1.0
± 0.1 Vp-p.
G
0V
G
0V
D
0V
D
0V
F
0V
D
0V
D
0V
19
ICF-CD555TV
Connection: (5-7-10 to 5-7-12)
5-7-10. VCO FREE RUN ADJUSTMENT
Condition:
Input the NTSC video signal (10 step (no burst)) (1 Vp-p 75
Input the NTSC video signal (10 step (no burst)) (1 Vp-p 75
Ω) to
the INPUT VIDEO jack (JK301) on the MAIN board from NTSC
pattern generator.
pattern generator.
Adjusting Procedure:
Adjust the
Adjust the
.
/
>
keys so that a screen on the monitor may
become normal.
5-7-11. PLL/V POS ADJUSTMENT
Condition:
Input the NTSC video signal (monoscope) (1 Vp-p 75
Input the NTSC video signal (monoscope) (1 Vp-p 75
Ω) to the
INPUT VIDEO jack (JK301) on the MAIN board from NTSC
pattern generator.
pattern generator.
Adjusting Procedure:
Press the
Press the
.
/
>
keys to adjust so that the position of screen
on the monitor becomes vertically symmetric.
5-7-12. H POS ADJUSTMENT
Condition:
Input the NTSC video signal (monoscope) (1 Vp-p 75
Input the NTSC video signal (monoscope) (1 Vp-p 75
Ω) to the
INPUT VIDEO jack (JK301) on the MAIN board from NTSC
pattern generator.
pattern generator.
Adjusting Procedure:
Press the
Press the
.
/
>
keys to adjust so that the position of screen
on the monitor becomes horizontally symmetric.
NTSC pattern
generator
set
INPUT VIDEO jack
(JK301)
20
ICF-CD555TV
– TV BOARD (Component Side) –
TP1805
TP1806
RV1551
V COM Adjustment
RV1651
PLL Adjustment
Connecting and Adjustment Location:
– TV BOARD (Conductor Side) –
TP1508
TP1554
TP1955
TP1651
TP1904
TP1907
TP1411
TP1912
TP1911
TP1403
TP1401
TP1959
TP1958
TP1960
Click on the first or last page to see other ICF-CD555TV service manuals if exist.