Sony ICF-C160L Service Manual ▷ View online
– 5 –
Note: Follow the assembly procedure in the numerical order given.
SECTION 4
DIAL POINTER SETTING
3
Install the knob (TUNE) with
board shape position as shown
in Figure.
board shape position as shown
in Figure.
4
Install the knob (VOL)
with making position as
shown in Figure.
with making position as
shown in Figure.
5
Turn CV1 and RV1 shaft in
the arrow direction fully.
the arrow direction fully.
6
radio board
board shape
pointer
claw
A
knob (tune)
CV1
RV1
1
pointer
radio board
(Component side)
(Component side)
2
Set the pointer part
A
portion to claw of chassis.
Repeat the procedures in each adjustment several times, and the
frequency coverage and tracking adjustments should be finally done
by the trimmer capacitors.
frequency coverage and tracking adjustments should be finally done
by the trimmer capacitors.
SECTION 5
ELECTRICAL ADJUSTMENTS
– 6 –
[FM]
Setting:
BAND switch: FM
BAND switch: FM
[MW/LW]
Setting:
BAND switch: MW/LW
BAND switch: MW/LW
+
–
–
0.01 µF
+
–
–
AM RF SSG
30% amplitude
modulation by
400 Hz signal
Outlet level: as low as possible
modulation by
400 Hz signal
Outlet level: as low as possible
set
speaker terminal
level meter
Put the lead-wire an-
tenna close to the
set.
tenna close to the
set.
± 22.5 kHz frequency
deviation by 400 Hz
signal
deviation by 400 Hz
signal
FM RF SSG
set
speaker terminal
level meter
FM lead wire antenna terminal
+
–
–
frequency counter
IC2 pin
!ª
10 pF
FM FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
L4
CT4
86.5 MHz
109.5 Hz
FM TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
CT3
Frequency max
MW FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
L2
CT2
520 kHz
1,650 Hz
MW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1-1
CT1
600 kHz
1,400 Hz
LW FREQUENCY COVERAGE ADJUSTMENT
Adjust for a maximum reading on level meter.
CT6
Frequency min
AM IF ADJUSTMENT
Adjust for a maximum reading on level meter.
T1
455 kHz
LW TRACKING ADJUSTMENT
Adjust for a maximum reading on level meter.
L1-2
CT5
160 kHz
240 Hz
Clock Frequency Check
Confirm that the reading on the frequency counter is 4,800 ± 400
Hz.
If frequency is higher, change capacitor value of CV27.
If frequency is lower, change resistor value of R8.
Hz.
If frequency is higher, change capacitor value of CV27.
If frequency is lower, change resistor value of R8.
Adjustment Location:
RADIO board (Component Side)
L1–1: MW TRACKING
ADJUSTMENT
L1–2: LW TRACKING
ADJUSTMENT
CT3: FM TRACKING
ADJUSTMENT
CT1: MW TRACKING
ADJUSTMENT
CT2: MW FREQUENCY
COVERAGE
ADJUSTMENT
ADJUSTMENT
CT6: LW FREQUENCY
COVERAGE
ADJUSTMENT
ADJUSTMENT
L2: MW FREQUENCY
COVERAGE
ADJUSTMENT
ADJUSTMENT
CT4: FM FREQUENCY
COVERAGE
ADJUSTMENT
ADJUSTMENT
L4: FM FREQUENCY
COVERAGE
ADJUSTMENT
ADJUSTMENT
T1: AM IF
ADJUSTMENT
IC1
CT5: LW TRACKING
ADJUSTMENT
– 7 –
– 8 –
6-1.
PRINTED WIRING BOARDS
SECTION 6
DIAGRAMS
D1
H-8
D2
H-8
D3
H-7
D4
G-7
D5
G-8
D6
F-7
IC1
D-4
IC2
H-5
Q1
F-3
Q2
D-8
Q3
C-6
Q4
C-6
• Semiconductor
Location
Location
Ref. No. Location
Note on Printed Wiring Board:
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
•
¢
: internal component.
•
b
: Pattern from the side which enables seeing.
ICF-C160L
– 9 –
– 10 –
6-2.
SCHEMATIC DIAGRAM
Note on Schematic Diagram:
•
All capacitors are in µF unless otherwise noted. pF: µµF 50
WV or less are not indicated except for electrolytics and
tantalums.
WV or less are not indicated except for electrolytics and
tantalums.
•
All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
¢
: internal component.
•
C
: panel designation.
•
U
: B+ Line.
•
H
: adjustment for repair.
•
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
under no-signal (detuned) conditions.
no mark : FM
(
) : MW/LW
∗
: Impossible to measure
•
Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
•
Signal path.
F
: FM
f
: MW/LW
Note: The components identified by mark
!
or dotted line
with mark
!
are critical for safety.
Replace only with part number specified.
ICF-C160L
•
IC Block Diagram
IC1
CXA1019S
1
2
3
4
5
6
7
8
9
10
15
14
13
12
11
FM
DISCRIMINATOR
AF POWER AMP
AM FE
FM IF
TUNING
METER
AM IF DET AGC
FM FE
23
22
21
20
24
25
19
18 17 16
29 28 27 26
30
GND
GND
AF OUT
VCC
RIPPLE
FIL
TER
AF IN
DET OUT
AFC AGC
AFC AGC
IF GND
METER
N.C
FM IF IN
AM IF IN
FM/AM BAND
SELECT
FM/AM
IF OUT
FE GND
N.C
AM RF IN
FM RF
REG OUT
FM OSC
FM RF IN
AFC
AM OSC
VOL
NF
FM DISCRI
GND
GND
Click on the first or last page to see other ICF-C160L service manuals if exist.