DOWNLOAD Sony HTC-W555 / MHC-W555 Service Manual ↓ Size: 4.57 MB | Pages: 57 in PDF or view online for FREE

– 5 –

CD

+ (AMS)  π (TAPE B)  button +  DISC3  button
= (AMS)  π (TAPE B)  button +  DISC1  button
)

 π (TAPE A)  button +  DISC3  button

0

 π (TAPE A)  button +  DISC1  button

TAPE A

+ (AMS)  DISC SKIP  button +  ·  (TAPE B)

TAPE B

= (AMS)  DISC SKIP  button +  ª  (TAPE B)
)

 DISC SKIP  button +  ·  (TAPE A)

0

 DISC SKIP  button +  ª  (TAPE A)

This unit cannot be operated by itself as it does not come with a power supply.
Connect STR-W555/W777 as shown in “Connection 1” before beginning servicing.

Connection 1: If there is STR-W555/W777.

STR-W555/W777

SYSTEM CABLE 17P

SET

AC IN

Use a power supply jig (PFJ-1) if the STR-W555/W777 is not available.
Connect the conversion jig for connection (J-2501-138-A) as shown in “Connection 2” before beginning servicing.

Connection 2: If there is not STR-W555/W777.

Set

Conversion

Jig

(J-2501-138-A)

Power SW

Service Box (PFJ-1)

Connector

cable 17P

(Supplied with PFJ-1)

Connector

cable 17P

(Supplied with

Conversion Jig or Set)

FH-E939,838,737
MHC-6600,5600,3600,2600
CDP/TC

SYSTEM CONTROL

To operate the unit by itself, turn on the power of the conduction jig (PFJ-1), and press the  π (TAPE A)  ,  π (TAPE B)  , and  · (TAPE
B)   buttons together in this order.

As this unit is not equipped with fast forward and rewind buttons, buttons need to be combined and pressed together for different functions
when operating the unit by itself. (See Table-2.)
However, it will not operate properly if operations are performed without switching the functions.
Perform the following procedure to switch the functions before operating the unit.
The function selected is indicated by the  DISC NUMBER  indicator.

Function

CD

p (CD)  button

1` 2` 3

+  HI-SPEED DUBBING  button

TAPE A

p (CD)  button

1` 2 3

+  r REC  button

TAPE B

p (CD)  button

1 2`  3

+  ª (TAPE A)  button

Operation

The function can be differentiated by the lighting of this part of the indicator.

↓

↓

1` 2` 3

Indicator

Deck

Function

Operation

– 6 –

Precedure:
1. After turning ON the power of the conduction jig (PFJ-1), press the  π (TAPE A)  button,  π (TAPE B)  button, and  · (TAPE B)  button

together in this order.

2. Press the  π (TAPE B)  button while pressing the  p (CD)  button to set the aging mode and start aging.
3. To end aging, press the three buttons in step 1.

NOTE: This is the mode for operating the unit by itself. Take note that the operating method differs when connected to the STR-W555/

W777. This method is described in the manuals of the STR-W555 and STR-W777. Refer to these manuals for details.

Precedure:
1. After turning ON the power of the conduction jig (PFJ-1), press the  π (TAPE A)  button,  π (TAPE B)  button, and  · (TAPE B)  button

together in this order.

2. Press the  P (TAPE)  button while pressing the  p (CD)  button.

NOTE: This is the mode for operating the unit by itself. Take note that the operating method differs when connected to the STR-W555/

W777. This method is described in the manuals of the STR-W555 and STR-W777. Refer to these manuals for details.
This mode moves the pickup to areas where the anti-vibration is stronger. Perform this mode when returning the repaired product
to the customer.

Precedure:
1. After turning ON the power of the conduction jig (PFJ-1), press the  π (TAPE A)  button,  π (TAPE B)  button, and  · (TAPE B)   button

together in this order.

2. Press the  CD SYNCHRO  button while pressing the  p (CD)  button.
3. Wait untill  r (TAPE B)  indicator is on befor disconnect from the conduction jig (PFJ-1).

NOTE: Always perform this mode when operating the unit by itself.

This mode is used for lighting up the whole LED.

Precedure:
1. After turning ON the power of the conduction jig (PFJ-1), press the  π (TAPE A)  button,  π (TAPE B)  button, and  · (TAPE B)  button

together in this order.

2. The whole LED can be turned on and off each time the  π (TAPE A)  button is pressed while pressing the  p (CD)  button.
3. Press the three buttons in step 1 at the end.

NOTE: Always perform this mode when operating the unit by itself.

This mode is used for checking the key inputs of the buttons of the unit.

Precedure:
1. After turning ON the power of the conduction jig (PFJ-1), press the  π (TAPE A)  button,  π (TAPE B)  button, and  · (TAPE B)

button together in this order.

2. Press the   DOLBY NR  button while pressing the  p (CD)  button to set the key check mode, and the indicator displays “

3 ·P”.

3. The number of buttons pressed are indicated in binary digits by the indicator LED. Buttons pressed once are not counted when pressed

again.

4. Press the two buttons in step 2 at the end.

Display: 

1` 2` 3

Aging Mode
NOTE: Perform the following procedure only when operating the unit by itself.

This mode is used for checking the operations of the CD player and tape deck.
The operations are the same as the aging mode described in the service manual for the STR-W555/W777. However as this unit does
not have a fluorescent indicator tube, operating states and error statuses cannot be checked.
If the STR-W555/W777 is available, set the aging mode according to those service manuals.

Aging continues in the following sequence as long as no errors occur.

MSB 

↑

↑

 LSB

Aging of CD player (12 minutes)

Aging of deck A

Aging of deck B

12 minutes

– 7 –

DISC SKIP/EX-CHANGE button

DISC 1 button

DISC 2 button

DISC 3 button

DISC NUMBER 

1` 2` 3 indicator

( (CD play) indicator

P (CD pause) indicator

6 OPEN/CLOSE button

p (CD stop) button

·P (CD play pause) button

œ (Deck A play) indicator

r (Deck B rec) indicator

P (Tape (Deck B pause)) indicator

œ (Deck B play) indicator

· (Deck B play) button

ª (Deck B play) button

π (Deck B stop) button

§ (Deck B eject) button

Casette lid (Deck B)

DIRECTION MODE button

P PAUSE button

r REC button

HI-SPEED DUBBING button

CD SYNCHIRO button

DOLBY NR button

Casette lid (Deck A)

§ EJECT (Deck A) button

π (Deck A stop) button

ª (Deck A play) button

· (Deck A play) button

CD Disc tray

– 8 –

 Follow the disassembly procedure in the numerical order given.

2

Pull-out the disc tray.

1

 Turn the cam to the

    direction of arrow.

3

 Loading panel

    (Remove two claws)

Two claws

1

 Screw

    (BVTP3x8)

2

 Cover (SC)

4

 Two screws

    (BVTP3x10)

3

 System cable

5

 Three screws

    (BVTP3x10)

6

 Two screws

    (BVTP3x8)

7

 Back panel

8

 Two screws

    (BVTP3x10)

!º

 Screw

    (BVTP3x10)

!¡

 Flat type wire

    (19core, CNS103)

!™

 Connector

    (CN111)

!£

 Connector

    (CN112)

!¢

 CD mechanism deck

9

 Dummy board