DOWNLOAD Sony HT-XT3 Service Manual ↓ Size: 7.39 MB | Pages: 92 in PDF or view online for FREE

Note: Tie the wires properly with clamp according
 

to this wire setting.

3

u 14), tapping)

4

4

4

5

5

2

u 14), tapping)

1

u 14), tapping)

7

8

9

qa

qa

qa

qa

0

0

6

Note: When wrapping the wires, ensure that the
 

acoustic tape is wrap correctly.  

Note 1: Please spread a sheet under 
 

a unit not to injure glass section.

Note 2: When installing the loudspeaker (11CM), be careful not to 
 

pinch the speaker cable between the loudspeaker (11CM) 

 

and the cabinet section.

2

4

2

4

3

3

3

3

1

u 14), tapping)

1

u 14), tapping)

COLD  RESET
The cold reset clears certain data in this system without initialize 
Personal Information and some operation data.
Execute this mode when returning the unit to the customers.

1.  Touch the [

?/1

] touch key on the main unit to turn the power 

on.

2.  Touch the [

?/1

] touch key and [VOL –] touch key on the main 

unit simultaneously for fi ve seconds.

3.  The message “WAIT” appears and then “RESET” appears on 

the fl uorescent indicator tube, then becomes standby states.

1.  Touch the [

?/1

] touch key on the main unit to turn the power 

on.

2.  Press button in order of the [

x

] 

[DISPLAY] [m] [M] 

on the remote commander.

 

(Make the interval when each button is pressed within two 
seconds).

3.  All segments in fl uorescent indicator tube are lighted up and 

then is dimmed after a second.

4.  In the state of step 3, press the [INPUT +] button on the remote 

commander and “K 0” is displayed on the fl uorescent indicator 
tube.

5.  In the state of step 4, press the [VOL +] button on the remote 

commander and “XZ3_A” is displayed on the fl uorescent 
indicator tube.

6.  In the state of step 5, press the [VOL –] button on the remote 

commander and all segments in fluorescent indicator tube are 
lighted up and then is dimmed after a second.

7.  In the state of step 6, press the [

x

] button on the remote com-

mander and “1   24” is displayed on the fluorescent indicator 
tube.

Releasing method:
To release from this mode, touch the [

?/1

] touch key on the main 

unit or press the [

?/1

] button on the remote commander.

1.  Touch the [

?/1

] touch key on the main unit to turn the power 

on.

2.  Press button in order of the [

x

] 

[DISPLAY] [VOL –] 

[M] on the remote commander.

  The message “MSURE” is displayed on the fl uorescent 

indicator tube.

3.  In the state of step 2, press [DIMMER] button on the remote 

commander.

 

The message will appear in order of the “FULL” 

“THRU” 

 “F2S” “F2SB” “F2CW” on the fl uorescent indicator 
tube.

4.  In the state of step 3, press [

m

] button on the remote 

commander.

 

The message will appear in order of the “A.OFF” 

“A.ON” 

on the fl uorescent indicator tube.

5.  In the state of step 4, press [ ] button on the remote 

commander.

 

The message will appear in order of the “V.N” 

“V.MSM” on 

the fluorescent indicator tube.

6.  In the state of step 5, press [CLEARAUDIO+] button on the 

remote commander.

 

The message will appear in order of the “VAON” 

“VAOFF” 

on the fluorescent indicator tube.

7.  In the state of step 6, press [VOICE] button on the remote 

commander to adjust the volume gain.

 

It can be adjusted between -3.0 to +3.0 (increase everytime 0.1 
step).

 

Eg: When gain +1.0 dB by pressing the [VOICE] button, the 
message “G +1.0” will appear on the fluorescent indicator 
tube.

8.  In the state of step 7, press [NIGHT] button on the remote 

commander to adjust the volume gain.

 

It can be adjusted between +3.0 to -3.0 (decrease everytime 0.1 
step).

 

Eg: When gain -1.0 dB by pressing the [NIGHT] button, the 
message “G -1.0” will appear on the fluorescent indicator tube.

FACTORY  INITIALIZE
Return all of the unit setting to their factory defaults.

Note 1: Disconnect the following connections when you use this mode.
 

   

 USB

Note 2: The operation in this mode must use a remote commander and TV 

monitor.

1.  Touch the [

?/1

] touch key on the main unit to turn the power 

on.

2.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

3. Select 

“Setup” 

 “Resetting”, and press the [ ] button on the 

remote commander.

Easy Network Settings

Easy Setup

Input Skip Setting

Resetting

4.  Select “Initialize Personal Information”, and press the [ ] 

button on the remote commander.

Initialize Personal Information
Delete personal data when disposing

Reset to Factory Default Settings

5.  Select “OK”, and press the [ ] button on the remote com-

mander.

Initialize Personal Information

OK

Cancel

Deleting Personal Information.
Do you want to proceed?
If you destroy or transfer or resell this
unit, please delete all Personal Information
for security reasons.
Please take appropriate measures such as 
logging out after using a network service.

6.  The message “Close” appears, and press the [ ] button on the 

remote commander.

Initialize Personal Information

Close

Initialization complete.

7.  Select “Reset to Factory Default Settings”, and press the [ ] 

button on the remote commander.

Initialize Personal Information

Reset to Factory Default Settings
Restore each setting to the factory
default setting.

8.  Select “All Settings”, and press the [ ] button on the remote 

commander.

Reset to Factory Default Settings

Audio Settings
Bluetooth Settings
System Settings
Input Skip Setting
Network Settings
All Settings

9.  Select “Start”, and press the [ ] button on the remote com-

mander.

All Settings

Restore all settings to the factory default
settings. The system will turn off after
reset.

Start

Cancel

10.  Initialization ends when the message “HELLO” on the fluores-

cent indicator tube disappears.

Note: The operation in this mode must use a remote commander and TV 

monitor.

Setting method of the SVC service mode:
1.  Connect this unit with the TV monitor.
2.  Touch the [

?/1

] touch key on the main unit to turn the power 

on.

3.  Press button in order of the [x] [DISPLAY] [X] [M] 

on the remote commander.

 

(Make the interval when each button is pressed within two 
seconds).

4.  The message “SVC” displayed on the fl uorescent  indicator 

tube. The OSD menu on TV monitor can be operated by the 
remote commander.

1. Main Functions
• Diag
 

Performs unit test of devices installed on the board.

• Log
 

Error log is displayed. Displayed contents can also be saved in 
an USB memory device.

• Factory 

Initialize

 

Restores the unit to its factory settings.

• Network
 Not 

used.

• Version 

Up

 Not 

used.

• System 

Information

 

Displays the system information of the unit.

 

Displays information such as the software version, drive infor-
mation, etc.

• EMC 

Test 

Mode

 Not 

used.

• Drive
 Not 

used.

• HDD 

mode

 Not 

used.

• RF 

Test 

Mode

 Not 

used.