Sony HT-XT100 Service Manual ▷ View online
HT-XT100
13
2-11. LOUDSPEAKER (4.3 × 12 cm) (SP2, SP3)
– Front panel block top rear view –
– Front panel block bottom front view –
1
terminal
(wide
side)
[white]
1
terminal
(narrow
side)
[black]
1
terminal
(narrow
side)
[yellow]
speaker cord
speaker terminal
OK
How to install the speaker terminal
Insert the speaker terminal straight into the interior.
There is a possibility that using this unit without the
speaker terminal correctly installed will damage it.
Insert the speaker terminal straight into the interior.
There is a possibility that using this unit without the
speaker terminal correctly installed will damage it.
Insert straight into the interior.
speaker cord
speaker terminal
NG
nsert only part way.
:LUHVHWWLQJ
– Rear view –
top side
loudspeaker
(4.3
(4.3
u 12 cm)
(SP2)
[white]
(wide side)
(wide side)
groove
hook
[yellow]
(narrow side)
(narrow side)
1
terminal
(wide
side)
[white]
2 four screws
(3
(3
u 10 B)
2 four screws
(3
(3
u 10 B)
3 loudspeaker
(4.3
(4.3
u 12 cm)
(SP2)
3 loudspeaker
(4.3
(4.3
u 12 cm)
(SP3)
:LUHVHWWLQJ
– Rear view –
top side
loudspeaker
(4.3
(4.3
u 12 cm)
(SP3)
[white]
(wide side)
(wide side)
groove
hook
[black]
(narrow side)
(narrow side)
HT-XT100
14
2-12. LOUDSPEAKER (1.4 × 2.5 cm) (SP4, SP5)
– Front panel block top rear view –
2 screw
(2.6
(2.6
u 8 S)
2 screw
(2.6
(2.6
u 8 S)
1
terminal
(wide
side)
[black]
1
terminal
(wide
side)
[black]
1
terminal
(narrow
side)
[red]
2 screw
(2.6
(2.6
u 8 S)
2 screw
(2.6
(2.6
u 8 S)
1
terminal
(narrow
side)
[red]
3 loudspeaker
(1.4
(1.4
u 2.5 cm)
(SP4)
3 loudspeaker
(1.4
(1.4
u 2.5 cm)
(SP5)
speaker cord
speaker terminal
OK
How to install the speaker terminal
Insert the speaker terminal straight into the interior. There is a possibility that
using this unit without the speaker terminal correctly installed will damage it.
Insert the speaker terminal straight into the interior. There is a possibility that
using this unit without the speaker terminal correctly installed will damage it.
Insert straight into the interior.
speaker cord
speaker terminal
NG
nsert only part way.
:LUHVHWWLQJ
– Rear view –
top side
loudspeaker
(1.4
(1.4
u 2.5 cm)
(SP5)
loudspeaker
(4.3
(4.3
u 12 cm)
(SP3)
screw hole
[black]
(wide side)
(wide side)
[red]
(narrow side)
(narrow side)
:LUHVHWWLQJ
[black]
(wide side)
(wide side)
[red]
(narrow side)
(narrow side)
loudspeaker
(4.3
(4.3
u 12 cm)
(SP2)
loudspeaker
(1.4
(1.4
u 2.5 cm)
(SP4)
screw hole
– Rear view –
top side
HT-XT100
15
2-13. KEY BOARD
– Front panel block top rear view –
1 two screws
(2.6
(2.6
u 8 S)
6 two screws
(2.6
(2.6
u 6 S)
7 two claws
8 button
9 KEY board
KEY board block
FRONT board
NFC wire
screw hole
2 Lift up the KEY board block
in the direction of the arrow.
3 connector
(XP13)
(XP13)
4 FFC 8P/FRONT-KEY (FFC3)
(XP12)
(XP12)
FFC 8P/FRONT-KEY
(FFC3)
(FFC3)
:LUHVHWWLQJ
– Rear view –
top side
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
5 KEY board block
terminal side
HT-XT100
16
2-14. NFC MODULE
Note: When replacing the BT NFC board or the NFC module, be sure
replace both at the same time.
The BT NFC board or the NFC module cannot replace with single.
– Front panel block top rear view –
1 Peel off the adhesive sheet.
3 NFC module
2 Draw the wire out of the
hole in front panel.
NFC module
guide line
How to install the NFC module
– Top view –
Click on the first or last page to see other HT-XT100 service manuals if exist.