Sony HT-XT100 Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Published by Sony Techno Create Corporation
HT-XT100
SPECIFICATIONS
HOME THEATRE SYSTEM
9-896-125-02
2015D33-1
©
2015.04
US Model
Canadian Model
AEP Model
UK Model
Australian Model
Ver. 1.1 2015.04
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
Amplifier section
U.S. models:
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
(FTC)
Front L + Front R:
With 4 ohms loads, both channels
driven, from 200 Hz - 20,000 Hz; rated
10 Watts per channel minimum RMS
power, with no more than 1% total
harmonic distortion from
250 milliwatts to rated output.
With 4 ohms loads, both channels
driven, from 200 Hz - 20,000 Hz; rated
10 Watts per channel minimum RMS
power, with no more than 1% total
harmonic distortion from
250 milliwatts to rated output.
POWER OUTPUT (reference):
Front L/Front R speaker:
20 Watts (per channel at 4 ohms,
1 kHz)
Subwoofer:
40 Watts (at 4 ohms, 100 Hz)
20 Watts (per channel at 4 ohms,
1 kHz)
Subwoofer:
40 Watts (at 4 ohms, 100 Hz)
Except US models:
POWER OUTPUT (rated)
POWER OUTPUT (rated)
Front L + Front R:
10 W + 10 W (at 4 ohms, 1 kHz, 1% THD)
10 W + 10 W (at 4 ohms, 1 kHz, 1% THD)
POWER OUTPUT (reference)
Front L/Front R speaker:
20 Watts (per channel at 4 ohms,
1 kHz)
Subwoofer:
40 Watts (at 4 ohms, 100 Hz)
20 Watts (per channel at 4 ohms,
1 kHz)
Subwoofer:
40 Watts (at 4 ohms, 100 Hz)
Inputs
ANALOG IN
DIGITAL IN
DIGITAL IN
Output
HDMI OUT ARC
HDMI Section
Connector
Connector
Type A (19pin)
USB Section
(USB) port
Type A
BLUETOOTH section
Communication system
Communication system
BLUETOOTH Specification version 4.0
Output
BLUETOOTH Specification Power Class
2
2
Maximum communication range
Line of sight approx. 10 m (33 ft)
1)
Maximum number of devices to be
registered
8 devices
8 devices
Frequency band
2.4 GHz band (2.4000 GHz -
2.4835 GHz)
2.4835 GHz)
Modulation method
FHSS (Freq Hopping Spread Spectrum)
Compatible BLUETOOTH profiles
2)
A2DP (Advanced Audio Distribution
Profile)
AVRCP (Audio Video Remote Control
Profile)
Profile)
AVRCP (Audio Video Remote Control
Profile)
Supported Codecs
3)
SBC
4)
Transmission range (A2DP)
20 Hz - 20,000 Hz (Sampling frequency
44.1 kHz)
44.1 kHz)
1)
The actual range will vary depending on
factors such as obstacles between
devices, magnetic fields around a
microwave oven, static electricity,
cordless phone, reception sensitivity,
operating system, software application,
etc.
factors such as obstacles between
devices, magnetic fields around a
microwave oven, static electricity,
cordless phone, reception sensitivity,
operating system, software application,
etc.
2)
BLUETOOTH standard profiles indicate
the purpose of BLUETOOTH
communication between devices.
the purpose of BLUETOOTH
communication between devices.
3)
Codec: Audio signal compression and
conversion format
conversion format
4)
Subband Codec
Speakers
Front L/Front R speaker section
Speaker system
Speaker system
2-way speaker system, Acoustic
suspension
suspension
Speaker
Tweeter: 14 mm - 25 mm (
9
/
16
in - 1 in)
balance dome type
Woofer: 43 mm × 120 mm (1
Woofer: 43 mm × 120 mm (1
3
/
4
in ×
4
3
/
4
in) cone type
Subwoofer section
Speaker system
Speaker system
Subwoofer system
Bass reflex
Bass reflex
Speaker
100 mm (4 in) cone type
General
Power requirements
Power requirements
120 V AC, 60 Hz (US and Canadian models)
220 V - 240 V AC, 50 Hz/60 Hz
(AEP, Russian, UK and Australian models)
220 V - 240 V AC, 50 Hz/60 Hz
(AEP, Russian, UK and Australian models)
Power consumption
On: 25 W
Standby mode (Control for HDMI is set
to on): 6 W or less
Standby mode (Control for HDMI is set
to off): 0.5 W or less
BLUETOOTH Standby mode: 6 W or
less
Standby mode (Control for HDMI is set
to on): 6 W or less
Standby mode (Control for HDMI is set
to off): 0.5 W or less
BLUETOOTH Standby mode: 6 W or
less
Dimensions (approx.) (w/h/d)
702 mm × 79 mm × 311 mm
(27
(27
3
/
4
in × 3
1
/
8
in × 12
1
/
4
in)
Mass (approx.)
6.5 kg (14 Ib 6 oz)
Supplied accessories
Remote control (1)
R03 (size AAA) batteries (2)
Optical digital cable (1)
R03 (size AAA) batteries (2)
Optical digital cable (1)
Design and specifications are subject to
change without notice.
change without notice.
HT-XT100
2
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
After correcting the original service problem, perform the follow-
ing safety check before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operated AC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2 V AC range are suitable. (See
Fig. A)
1.5 k
Ω
0.15
μF
AC
voltmeter
(0.75 V)
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Parts on Set
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!
COMPONENTS IDENTIFIED BY MARK
0 OR DOTTED LINE
WITH MARK
0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE
0 SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONC-
TIONNEMENT. NE REMPLACER CES COMPOSANTS QUE
PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DON-
NÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
This system incorporates Dolby* Digital
Surround System.
Surround System.
* Manufactured under license from
Dolby Laboratories.
Dolby, and the double-D symbol are
trademarks of Dolby Laboratories.
Dolby, and the double-D symbol are
trademarks of Dolby Laboratories.
The BLUETOOTH
®
word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under
license.
Bluetooth SIG, Inc. and any use of such
marks by Sony Corporation is under
license.
This system incorporates
High-Definition Multimedia Interface
(HDMI™) technology.
The terms HDMI and HDMI
High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or
registered trademarks of HDMI
Licensing LLC in the United States and
other countries.
High-Definition Multimedia Interface
(HDMI™) technology.
The terms HDMI and HDMI
High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or
registered trademarks of HDMI
Licensing LLC in the United States and
other countries.
The N Mark is a trademark or registered
trademark of NFC Forum, Inc. in the
United States and in other countries.
trademark of NFC Forum, Inc. in the
United States and in other countries.
Android is a trademark of Google Inc.
“ClearAudio+” is a trademark of Sony
Corporation.
Corporation.
Other trademarks and trade names are
those of their respective owners.
those of their respective owners.
Copyrights and Trademarks
HT-XT100
3
1.
SERVICING NOTES
.............................................
4
2. DISASSEMBLY
2-1. Disassembly
Flow
........................................................... 6
2-2. Bottom
Panel
................................................................... 7
2-3. BT NFC Board ................................................................ 7
2-4. AMP
2-4. AMP
Block
..................................................................... 8
2-5. Power Cord (AC1) .......................................................... 9
2-6. POWER
2-6. POWER
Board
................................................................ 9
2-7. MAIN
Board
................................................................... 10
2-8. Loudspeaker (10 cm) (SP1) ............................................ 10
2-9. Grille
2-9. Grille
Assy
...................................................................... 11
2-10. Front Panel Block ........................................................... 12
2-11. Loudspeaker (4.3 × 12 cm) (SP2, SP3) .......................... 13
2-12. Loudspeaker (1.4 × 2.5 cm) (SP4, SP5) ......................... 14
2-13. KEY Board ...................................................................... 15
2-14. NFC Module ................................................................... 16
2-11. Loudspeaker (4.3 × 12 cm) (SP2, SP3) .......................... 13
2-12. Loudspeaker (1.4 × 2.5 cm) (SP4, SP5) ......................... 14
2-13. KEY Board ...................................................................... 15
2-14. NFC Module ................................................................... 16
3.
TEST MODE
............................................................ 17
4. DIAGRAMS
4-1. Block
Diagram
................................................................ 19
4-2. Printed Wiring Board - MAIN Board - ........................... 21
TABLE OF CONTENTS
4-3. Schematic Diagram - MAIN Board (1/6) - ..................... 22
4-4. Schematic Diagram - MAIN Board (2/6) - ..................... 23
4-5. Schematic Diagram - MAIN Board (3/6) - ..................... 24
4-6. Schematic Diagram - MAIN Board (4/6) - ..................... 25
4-7. Schematic Diagram - MAIN Board (5/6) - ..................... 26
4-8. Schematic Diagram - MAIN Board (6/6) - ..................... 27
4-9. Printed Wiring Board - BT NFC Board - ........................ 28
4-10. Schematic Diagram - BT NFC Board - ........................... 28
4-11. Printed Wiring Board - USB Board - .............................. 29
4-12. Schematic Diagram - USB Board - ................................. 29
4-13. Printed Wiring Board - KEY Board -.............................. 29
4-14. Schematic Diagram - KEY Board - ................................ 29
4-15. Printed Wiring Board - FRONT Board - ......................... 30
4-16. Schematic Diagram - FRONT Board - ........................... 31
4-17. Printed Wiring Board - POWER Board - ........................ 32
4-18. Schematic Diagram - POWER Board - .......................... 32
4-4. Schematic Diagram - MAIN Board (2/6) - ..................... 23
4-5. Schematic Diagram - MAIN Board (3/6) - ..................... 24
4-6. Schematic Diagram - MAIN Board (4/6) - ..................... 25
4-7. Schematic Diagram - MAIN Board (5/6) - ..................... 26
4-8. Schematic Diagram - MAIN Board (6/6) - ..................... 27
4-9. Printed Wiring Board - BT NFC Board - ........................ 28
4-10. Schematic Diagram - BT NFC Board - ........................... 28
4-11. Printed Wiring Board - USB Board - .............................. 29
4-12. Schematic Diagram - USB Board - ................................. 29
4-13. Printed Wiring Board - KEY Board -.............................. 29
4-14. Schematic Diagram - KEY Board - ................................ 29
4-15. Printed Wiring Board - FRONT Board - ......................... 30
4-16. Schematic Diagram - FRONT Board - ........................... 31
4-17. Printed Wiring Board - POWER Board - ........................ 32
4-18. Schematic Diagram - POWER Board - .......................... 32
5.
EXPLODED VIEWS
5-1. Bottom
Section
............................................................... 40
5-2. Front Panel Section ......................................................... 41
6. ACCESSORIES
....................................................... 42
HT-XT100
4
SECTION 1
SERVICING NOTES
The SERVICING NOTES contains important information for servicing. Be sure to read this section before repairing the unit.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
about 350 °C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong
viscosity
Unleaded solder is more viscous (sticky, less prone to fl ow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
DESTINATION ABBREVIATIONS
The following abbreviations for model destinations are used in this
service manual.
The following abbreviations for model destinations are used in this
service manual.
• Abbreviations
AUS :
AUS :
Australian
model
CND : Canadian model
RU
RU
: Russian model
MODEL IDENTIFICATION
Distinguish by model number label stuck on the rear side of a main
unit.
Distinguish by model number label stuck on the rear side of a main
unit.
Note: The printed contents of following fi gure model number label may
be different from the model number label of a main unit.
– Rear view –
US and Canadian models (UC2)
MODEL NUMBER LABEL
UK model (CEK)
AEP model (CEL)
Australian model (AU1)
4-562-642-0
[]
4-562-643-0
[]
4-562-644-0
[]
4-562-779-0
[]
Russian model (RU3)
4-562-790-0
[]
Ver. 1.1