Sony HT-SS1000 Service Manual ▷ View online
37
STR-KS1000
Pin No.
Pin Name
I/O
Description
51
VSS
-
Ground terminal
52, 53
PAGE1, PAGE0
O
External memory page selection signal output terminal Not used
54
BOOT
I
Boot mode control signal input terminal Not used
55
TST1
O
Output terminal for the test Not used
56
BST
I
Boot strap signal input terminal
57
MOD1
I
Operation mode setting terminal "L": enhanced mode, "H": normal mode
Fixed at "H" in this set
Fixed at "H" in this set
58
MOD0
I
Operation mode setting terminal "L": single chip mode, "H": can not use
Fixed at "L" in this set
Fixed at "L" in this set
59
EXLOCK
I
PLL lock error signal and data error flag input from the digital audio interface receiver
60
VDDI
-
Power supply terminal (+1.8V)
61
VSS
-
Ground terminal
62, 63
A17, A16
O
Address signal output terminal Not used
64 to 66
A15 to A13
O
Address signal output to the S-RAM
67
GP10
I
L/R sampling clock signal (44.1 kHz) input terminal
68
GP9
O
Read ready signal output to the system controller
69
GP8
I
PCM audio data input from the digital audio interface receiver
70
VDDI
-
Power supply terminal (+1.8V)
71
VSS
-
Ground terminal
72 to 75
D15 to D12
I/O
Two-way data bus with the S-RAM
76
VDDE
-
Power supply terminal (+3.3V)
77 to 80
D11 to D8
I/O
Two-way data bus with the S-RAM
81
VSS
-
Ground terminal
82 to 85
A9, A12 to A10
O
Address signal output to the S-RAM
86
TDO
O
Simplicity emulation data output terminal Not used
87
TMS
I
Simplicity emulation data input start and end terminal Not used
88
XTRST
I
Simplicity emulation non-sync break signal input terminal Not used
89
TCK
I
Simplicity emulation clock signal input terminal Not used
90
TDI
I
Simplicity emulation data input terminal Not used
91
VSS
-
Ground terminal
92 to 97
A8 to A3
O
Address signal output to the S-RAM
98, 99
D7, D6
I/O
Two-way data bus with the S-RAM
100
VDDI
-
Power supply terminal (+1.8V)
101
VSS
-
Ground terminal
102 to 105
D5 to D2
I/O
Two-way data bus with the S-RAM
106
VDDE
-
Power supply terminal (+3.3V)
107, 108
D1, D0
I/O
Two-way data bus with the S-RAM
109, 110
A2, A1
O
Address signal output to the S-RAM
111
VSS
-
Ground terminal
112
A0
O
Address signal output to the S-RAM
113
PM
I
PLL initialize signal input from the system controller
114, 115
SDI3, SDI4
I
Audio serial data input terminal Not used
116
SYNC
I
Sync/non-sync setting terminal "L": sync, "H": non-sync Fixed at "H" in this set
117
TST2
O
Output terminal for the test Not used
118
GP11
-
Not used
119
TST3
O
Output terminal for the test Not used
120
VDDI
-
Power supply terminal (+1.8V)
38
STR-KS1000
PLACA PRINCIPAL IC1601 MB90488BPF-G-181E1 (SYSTEM CONTROLLER)
Pin No.
Pin Name
I/O
Description
1
DATA0
I
Audio serial data input from the digital audio interface receiver
2
GP9
I
Read ready signal input from the digital audio signal processor
3
BST
O
Boot strap signal output to the digital audio signal processor
4
HCS
O
Chip select signal output to the digital audio signal processor
5
HACN
I
Acknowledge signal input from the digital audio signal processor
6
XRST
O
System reset signal output to the digital audio signal processor "L": reset
7
PM
O
PLL initialize signal output to the digital audio signal processor
8
PWM_DA
O
Power on/off control signal output terminal Not used
9
GP12
O
Write enable signal output to the digital audio signal processor
10
AD_RST
O
System reset signal output to the A/D converter
11
VSS
-
Ground terminal
12
HDMI-SW1
O
Source selection signal output to the HDMI receiver/transceiver and analog switch
13
HDMI-DET
I
HDMI jack detection signal input terminal
14
HDMI-OEB
O
Chip enable signal output to the HDMI receiver/transceiver "L": active
15
HDMIPRE
-
Not used
16
HDMI-CTL
O
Power on/off control signal output to the HDMI circuit
17
P-CONT2
O
Power on/off control signal output to the regulator IC and power supply circuit
18
HDOUT
I
Serial data input from the digital audio signal processor
19
HDIN
O
Serial data output to the digital audio signal processor
20
HCLK
O
Serial data transfer clock signal output to the digital audio signal processor
21, 22
SELECT_B,
SELECT_A
O
Audio select signal output to the analog audio input select
23
VCC5
-
Power supply terminal (+3.3V)
24, 25
NO USE
-
Not used
26
POWER_SD
I
Shut down state input from the digital power amplifier "L": shut down
27, 28
FLASH2,
FLASH1
-
Not used
29 to 31
NO USE
-
Not used
32
POWER_RS
O
Reset signal output to the digital power amplifier "L": reset
33
SCL
O
Serial data output to the EEPROM
34
SDA
I/O
Two-way data bus with the EEPROM
35
AVCC
-
Power supply terminal (+3.3V)
36
AVRH
I
Reference voltage (+3.3V) input terminal
37
AVSS
-
Ground terminal
38 to 40
A/D0 to A/D2
I
Front panel key input terminal (A/D input)
41
NO USE
-
Not used
42
VSS
-
Ground terminal
43
RDS SIGNAL
I
RDS signal input from the tuner (AEP, UK models only)
44
ADCC2
I
Mic signal input terminal
45
VERSION
I
Setting terminal for the destination
46
P.CONT1
O
Power on/off control signal output to the regulator IC
47
FUSE DETECT
-
Not used
48
STOP P.STOP
I
AC off detection signal input terminal
49 to 51
NO USE
-
Not used
52
RDS CLK
I
RDS serial data transfer clock signal input from the tuner (AEP, UK models only)
53
RDS DATA
I
RDS serial data input from the tuner (AEP, UK models only)
54
SIRCS
I
SIRCS signal input terminal
55
ADCC_INT
I
ADCC interrupt status input terminal
56
POWER KEY
I
Power key input terminal
39
STR-KS1000
Pin No.
Pin Name
I/O
Description
57
NO USE
-
Not used
58
LAT2
O
Latch control signal output to the stream processor
59, 60
NO USE
-
Not used
61
SHIFT
O
Shift clock signal output to the stream processor
62
SCDT
O
Serial data output to the stream processor
63
SOFT_MUTE
O
Soft muting on/off control signal output to the stream processor "L": muting on
64
INT
O
Reset signal output to the stream processor "L": reset
65
LAT1
O
Latch control signal output to the stream processor
66
TUNED
I
Tuning detection signal input from the tuner "L": tuned
67
TUNER LED
O
LED drive signal output of the tuner indicator "L": LED on
68
OVF
I
Over flow status input from the stream processor (front/surround/center)
69
LAT3
O
Latch control signal output to the stream processor
70, 71
VOLB, VOLA
I
Jog dial pulse input from the rotary encoder (for MASTER VOLUME)
72
FL_DIN
O
Serial data output to the fluorescent indicator tube
73
FL_CLK
O
Serial data transfer clock signal output to the fluorescent indicator tube
74
FL_STB
O
Strobe signal output to the fluorescent indicator tube
75, 76
NO USE
-
Not used
77
RSTX
I
System reset signal input terminal "L": reset
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
For several hundreds msec. after the power supply rises, "L" is input, then it change to "H"
78
OVFW
I
Over flow status input from the stream processor (sub woofer)
79, 80
X1A, X0A
-
Not used
81
VSS
-
Ground terminal
82
X0
I
System clock input terminal (24 MHz)
83
X1
O
System clock output terminal (24 MHz)
84
VCC3
-
Power supply terminal (+3.3V)
85
T.CLK
O
PLL serial data transfer clock signal output to the tuner
86
T.DATA
O
PLL serial data output to the tuner
87
SLATCH
O
Latch control signal output to the tuner
88
T_DO
I
PLL serial data input from the tuner
89
T_MUTE
O
Tuner muting on/off control signal output to the tuner
90
ST
I
FM stereo detection signal input from the tuner
91
NO USE
-
Not used
92
LRCK_SW
O
Signal switch signal output terminal "L": boot strap signal, "H": L/R sampling clock signal
93
XMODE
O
System reset signal output to the digital audio interface receiver "L": reset
94
CKSEL1
-
Not used
95
CLK
O
Serial data transfer clock signal output to the digital audio interface receiver
96
CE
O
Chip enable signal output to the digital audio interface receiver
97
DI
O
Serial data output to the digital audio interface receiver
98
DO
I
Serial data input from the digital audio interface receiver
99
ERROR
I
PLL lock error signal and data error flag input from the digital audio interface receiver
100
XSTATE
I
Source clock selection monitor input from the digital audio interface receiver
40
STR-KS1000
SEÇÃO 6
VISTA EXPLODIDAS
Ref. No.
Part No.
Description
Remark
Ref. No.
Part No.
Description
Remark
1 2-661-484-01
BOTÃO DE VOLUME (SL06)
2 X-2108-886-1 PAINEL FRONTAL MONTADO
3 4-977-358-01
3 4-977-358-01
CALÇO
4 A-8285-227-A PLACA DISPLAY MONTADA
5 3-087-053-01 +BVTP2.6 (3CR)
5 3-087-053-01 +BVTP2.6 (3CR)
6 3-070-883-41 PARAFUSO, TAPPING
7 2-661-487-01 TAMPA SUPERIOR (SL06)
7 2-661-487-01 TAMPA SUPERIOR (SL06)
8 1-869-120-11 PLACA VOLUME
9
9
A-1156-523-A ADCC BOARD, COMPLETE
11 3-378-435-01
CALÇO, SARANET
RV700 1-418-725-51 ENCODER, ROTATIVA (12 TYPE)
(MASTER VOLUME)
#2 7-685-645-79 PARAFUSO +BVTP 3X6 TYPE2 IT-3
#3 7-685-646-79 PARAFUSO +BVTP 3X8 TYPE2 IT-3
#3 7-685-646-79 PARAFUSO +BVTP 3X8 TYPE2 IT-3
1
seção principal
RV700
fornecido com RV700
#2
#3
2
4
5
5
5
5
3
3
#2
9
6
11
11
6
7
não fornecido
não fornecido
10
8
10 1-921-104-61 CABO TIPO FLAT (17 VIAS)
Os componentes identificados com
a marca 0 são críticos para a segu-
rança. Somente os substitua por pe-
ças numericamente identificadas
nesse manual.
a marca 0 são críticos para a segu-
rança. Somente os substitua por pe-
ças numericamente identificadas
nesse manual.
• Para substituição da placa montada
consulte o Suporte Técnico.
6
-1. SEÇÃO
GERAL
•
Items marcados com “*” são estocados visto
que são raramente solicitados para serviço de
rotina. Algum atraso deverá previsto quando
solicitar esses itens.
rotina. Algum atraso deverá previsto quando
solicitar esses itens.
•
As peças mecânicas sem o número de referência
nas vistas explodidas não são fornecidas.
NOT
A
:
•
-XX e -X são peças padronizadas, portanto
elas podem ter alguma diferença da original.
Click on the first or last page to see other HT-SS1000 service manuals if exist.