Sony HT-SF360 / HT-SS100 / HT-SS360 / STR-KS360 / STR-KS360S Service Manual ▷ View online
STR-KS360/KS360S
9
3-5. FRONT PANEL BLOCK
3-6. MAIN BOARD
1 wire (flat type) (15 core)
(CNS700)
2 saranet cushion
3 clamp (FCR-60)
4 screw
(BV3)
5 two claws
6 claw
8 front panel block
6 claw
7 three claws
screw
(BVTP3
(BVTP3
× 14)
heat sink (AMP)
RE MAIN board
RB radiation
sheet
sheet
(AMP)
RT radiation
sheet
sheet
(AMP)
wire (flat type) (15 core)
(CNS700)
(CNS700)
wire (flat type) (25 core)
(CNS201)
(CNS201)
wire (flat type) (17 core)
(CN1003)
connector
(CN906)
(CN906)
connector
(CN904)
(CN904)
two screws
(BV3)
(BV3)
three screws
(BV3)
(BV3)
screw
(BV3)
(BV3)
screw
(BV3)
(BV3)
two screws
(BV3)
(BV3)
STR-KS360/KS360S
10
SECTION 4
TEST MODE
1. COLD RESET
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. Press the [
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. Press the [
?/1
] button on the set to turn the power on.
2. Keeps pressing the [
?/1
] button on the set for about fi ve sec-
onds.
3. The message “CLEARED” appears, then the set turns off.
2. HOW TO ENTER THE TEST MODE
2. HOW TO ENTER THE TEST MODE
Note: The operation of the button of the following test modes is only a
remote commander.
Procedure:
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press the buttons in order of [DMPORT]
→ [RETURN] →
[ENTER]
→ [0] → [1] → [0] → [SOUND FIELD]
3. The message “TEST” appears, then enter the test menu.
4. Press the [
4. Press the [
?/1
] button to exit from the test mode.
3. PANEL TEST
3-1. Pattern check
Procedure:
1. Enter the test mode menu.
2. Press the [
3-1. Pattern check
Procedure:
1. Enter the test mode menu.
2. Press the [
↑]/[↓] buttons to select “PANEL”, and press the
[ENTER] button.
3. All segments and all LEDs turn on. Change as follows all on,
test pattern 1, test pattern 2, all on in this order.
3-2. Key check
Procedure:
1. Press the [VOLUME –] button, while executing pattern
Procedure:
1. Press the [VOLUME –] button, while executing pattern
check.
2. The message “K0 V0” appears. “K0” value increases when-
ever a button on the set is pressed. However, once a button has
been pressed, it is no longer taken into account. All buttons on
the set is pressed, “OK” and “K2” are alternately displayed.
been pressed, it is no longer taken into account. All buttons on
the set is pressed, “OK” and “K2” are alternately displayed.
3. “V” value increases in the manner of 0, 1, 2, 3 ... [MASTER
VOLUME] knob is turned clockwise, or it decreases in the
manner of 0, 9, 8, 7 ... [MASTER VOLUME] knob is turned
counterclockwise.
manner of 0, 9, 8, 7 ... [MASTER VOLUME] knob is turned
counterclockwise.
4. Press the [
?/1
] button to exit from the test mode.
3-3. Software version and destination display
Procedure:
1. Press the [VOLUME +] button, while executing pattern
check.
2. The display of model name, destination, and software version
changes whenever [VOLUME +] button is pressed.
3. Press the [
?/1
] button to exit from the test mode.
4. AMP TEST
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
5. TUNER FACTORY PRESET
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
6. VACS DISPLAY
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
7. VACS ON/OFF
Procedure:
1. Enter the test mode menu.
2. Press
Procedure:
1. Enter the test mode menu.
2. Press
the
[
↑]/[↓] buttons to select “VCS CTRL”, and press the
[ENTER] button.
3. VACS ON/OFF changes whenever this mode is decided.
(There is no change in the display)
8. DSP HALT MODE
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
9. DSP STATUS DISPLAY
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
10. HDMI UCOM UPDATE
Procedure:
1. Enter the test mode menu.
2. Press
Procedure:
1. Enter the test mode menu.
2. Press
the
[
↑]/[↓] buttons to select “HDMI VER”, and press the
[ENTER] button.
3. HDMI microprocessor software version is displayed.
4. Press the [
4. Press the [
?/1
] button to exit from the test mode.
11. DMPORT TEST
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN1701) on the MAIN board.
2. Press the [
?/1
] button to turn the power on.
3. Confi rm that both LEDs of the DMPORT check jig lights.
(Confi rmation the power supply line)
4. Press the [DMPORT] button to select the “DMPORT”.
5. Enter the test mode menu.
6. Press
5. Enter the test mode menu.
6. Press
the
[
↑]/[↓] buttons to select the “DMP CHK”, and press
the [ENTER] button.
7. The message “DMPORTOK.” appears on the fl uorescent indi-
cator tube and enter the digital media port test mode. (Confi r-
mation of communication line)
mation of communication line)
When “NO DET” and “UART TO” are displayed on the fl uo-
rescent indicator tube, confi rm the connection of the DMPORT
check jig, and enter the mode again.
rescent indicator tube, confi rm the connection of the DMPORT
check jig, and enter the mode again.
Each time the [
>
] button is pressed, the connect check and
adaptor version check are changed.
Press the [
.
] button, connected confi rmation of the
DMPORT check jig is done again.
8. To a pin-jack of the DMPORT check jig input information rel-
evant to audio signal (sine-wave 1.0 Vrms).
9. Confi rm the output of speakers. (Confi rmation of analog sig-
nal)
10. Press the [
?/1
] button to exit from the test mode.
AF
oscillator
DMPORT
check jig
(Part No.
J-2501-309-A)
J001
set
FL/FR
speakers
speakers
MAIN board
CN1701
MAIN board
TB3002
12. DMPORT DEVICE TEST
Note: It connects with the iPod adaptor and it is necessary to repair hard-
ness to execute this mode.
Procedure:
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
1. Connect the DMPORT check jig (Part No. J-2501-309-A) with
the DMPORT jack (CN1701) on the MAIN board.
2. Enter the test mode menu.
3. Press the [
3. Press the [
↑]/[↓] buttons to select “DMP DEV”, and press the
[ENTER] button.
4. LED on the jig lights.
5. Press the [
5. Press the [
?/1
] button to exit from the test mode.
STR-KS360/KS360S
STR-KS360/KS360S
11
11
SECTION 5
ELECTRICAL CHECK
13. S-AIR TEST MODE (KS360S only)
Procedure:
1. Enter the test mode menu.
2. Press the [
Procedure:
1. Enter the test mode menu.
2. Press the [
↑]/[↓] buttons to select “SAIR TST”, and press the
[ENTER] button.
3. S-AIR test menu is displayed.
4. Press the [
4. Press the [
?/1
] button to exit from the test mode.
13-1. Power
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
↑]/[↓] buttons to select “POWER”, and press the
[ENTER] button.
3. The messages “000 SET” is appears.
4. Press the [
4. Press the [
↑]/[↓] buttons to select the output power. (OFF or
000 to 063)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
13-2. NAMG
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
↑]/[↓] buttons to select “NAMG”, and press the
[ENTER] button.
3. The messages “116 SET” is appears.
4. Press the [
4. Press the [
↑]/[↓] buttons to select the NAMG setting value.
(107 to 117)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
13-3. Version
check
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
1. Enter the S-AIR test mode.
2. Press the [
↑]/[↓] buttons to select “VER. CHECK”, and press
the [ENTER] button.
3. uCom software version of S-AIR product is displayed.
4. Press the [ENTER] button, return to S-AIR test mode each
4. Press the [ENTER] button, return to S-AIR test mode each
item.
13-4. Encryption
key
Procedure:
1. Enter the S-AIR test mode.
2. Press the [
1. Enter the S-AIR test mode.
2. Press the [
↑]/[↓] buttons to select “ENC KEY”, and press the
[ENTER] button.
3. The on/off setting of the encryption key is displayed.
4. Press the [
4. Press the [
↑]/[↓] buttons to select the encryption key setting.
(ON or OFF)
5. Press the [ENTER] button, return to S-AIR test mode each
item.
14. S-AIR TEST ELEC MODE
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
15. UART FLASH (SOURCE)
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
16. UART FLASH (TARGET)
Not used for the servicing.
Press the [
Not used for the servicing.
Press the [
?/1
] button if having entered this mode.
17. COLD RESET
Procedure:
1. Enter the test mode menu.
2. Press
Procedure:
1. Enter the test mode menu.
2. Press
the
[
↑]/[↓] buttons to select “COLD RST”, and press the
[ENTER] button.
3. The message “CLEARED” appears, then the set turns off.
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
1. Turn on the set.
2. Input the following signal from signal generator to FM antenna
input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 35 dBu (EMF)
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
STR-KS360/KS360S
STR-KS360/KS360S
12
12
SECTION 6
DIAGRAMS
6-1. BLOCK DIAGRAM - MAIN Section -
LINE AMP
IC201
EEPROM
IC1014
SYSTEM CONTROLLER
IC1005 (1/4)
DIGITAL OPTICAL
RECEIVER
IC203
22
DA
TA
23
CLK
VIDEO1 L
3
TV L
5
SACD L
L CH
R CH
DO/ST/SD
DI
7
TUNER L
11
VinL
13
DIR_HDOUT
DAMP_SCDT/DIR_DIN
DAMP_SHIFT/DIR_CLK
DIR_HCE
DIR ERROR
DIR CSFLAG
DIR RST
DIR_XST
ATE
DIR_ZERO
18
BD3842CLK
87
BD3842DA
TA
86
43
DATA_DIR, DOUT,
BCK, LRCK, CKOUT
DOUT
6
SCKI
9
BCK 8
LRCK 7
OUT L 14
DO 35
DI 36
CLK 38
CE 37
ERROR(O) 34
XMODE 48
XSTATE(O)
DIR_DO
DIR_ZERO
DIR_DIN
DIR_CLK
DIR_CE
ERR
DIR_RST
DIR_XSTATE
DIR_DO
DIR_ZERO
DIR_DIN
DIR_CLK
DIR_CE
ERR
DIR_XMODE
DIR_XST
ATE
17
DATA(O) 16
BCK(O) 14
LRCK(O) 15
CKOUT
DATA_DIR
BCK
LRCK
DOUT
CKOUT
13
AUDIO(O) 24
TV
OPT IN
DIGITAL OPTICAL
RECEIVER
IC202
OPT IN
SAT
SCHMITT
TRIGGER
IC211
DIGITAL AUDIO
INTERFACE RECEIVER
IC1704
DIN1
J202
4
COAX IN
VIDEO 2
FM 75
Ω
COAXIAL
45
41
40
41
40
DIGITAL
VIDEO 1
AUDIO IN
TV
AUDIO IN
ANTENNA
J201
TUNER (FM/AM)
SA-CD/CD
AUDIO IN
AM
L
R
L
R
L
R
R-CH
DMPORT L
9
Lch
Rch
14
13
CN1701 (1/2)
R-CH
DMPORT RX (UCOM TX)
DMPORT TX (UCOM RX)
6
5
CN1701 (2/2)
R-CH
R-CH
ANALOG AUDIO
INPUT SELECTOR
IC212
A/D CONVERTER
IC1703
R-CH
21
22
X1700
12.288MHz
XOUT(O)
XIN(I)
FM ANT
GND
AM ANT
GND
CL
CE
ST_DI
ST_DO
ST_CLK
ST_CE
ST_DO
ST_CLK
ST_CE
LINE AMP
IC1705
42
75
75
RDS DATA
RDS CLK
RDS_DATA
RDS CLK
RDS CLK
44
TUNED_SD
TUNED
31 UCOM TX-DMP RX
32 UCOM RX-DMP TX
DET
7
91 DMPORT_DET
13
15
Xout
Xin
53
ROM_SDA
54
ROM_SCLK
X1001
5MHz
A
• SIGNAL PATH
: TUNER
: AUDIO (ANALOG)
: AUDIO (DIGITAL)
• R-ch is omitted due to same as L-ch.
DIGITAL AUDIO
INPUT SELECTOR
IC210
1C0
6
1C1
5
DIN0
3
1Y 7
2
B
14
A
TC74VHC153A
51
TC74VHC153B
66
AUTO
CAL MIC
J200
DCAC L
1
MIC AMP
IC209
DCACON/OFF
11
CEC DATA
SWITCH
Q1006 – 1009
36
UCOM RX-HDMI_TX
UCOM TX-HDMI_RX 35
UCOM TX-HDMI_RX 35
HDMI_RST
HTXD
HRXD
HRESET
94
22
CEC_DO
CEC_DI 3
AUDIO
B
DIR_XSTATE, DIR_RERR
SAIR OUT L
C
CEC
D
100 1 2 24
27
69 10
HRESET,
HTXD, HRXD
E
: MIC
DIN2
5
J
SPDIF
R-CH
DMPORT
DMPORT
PLUG DETECT
SWITCH
Q201
DIR_RERR
DIR_XSTATE
(KS360S: AEP, UK)
GAIN CONTROL
Q200
A+9V
LINE AMP
IC200
SAIR OUT L 18
CSFLAG(O) 25
DIR_CSFLAG
DIR_SCFLAG
19
M
SC_SHIFT, SC_SCDT
P
SC_SHIFT
SC_SCDT
(Page 13)
(Page 14)
(Page 14)
(Page 15)
(Page 14)
(Page 13)
(Page 13)
(Page 14)
Click on the first or last page to see other HT-SF360 / HT-SS100 / HT-SS360 / STR-KS360 / STR-KS360S service manuals if exist.