DOWNLOAD Sony HT-SF100 / HT-SS100 / STR-KS100 Service Manual ↓ Size: 3.24 MB | Pages: 68 in PDF or view online for FREE

Model
HT-SF100 HT-SS100 STR-KS100
Pages
68
Size
3.24 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio
File
ht-sf100-ht-ss100-str-ks100.pdf
Date
PREV: Sony ICF-C414 Service Manual

Sony HT-SF100 / HT-SS100 / STR-KS100 Service Manual ▷ View online

STR-KS100
45
Pin No.
Pin Name
I/O
Description
1
DAMP_SCDT/DIR_DIN
O
Serial data output to the digital audio interface receiver and stream processor
2
DAMP_SHIFT/
DIR_DINCLK
O
Serial data transfer clock signal output to the digital audio interface receiver and stream 
processor
3
CEC_DI
I
CEC serial data input from the HDMI connector
4
SIRCS_IN
I
SIRCS signal input from the remote control receiver
5
DSP_MOSI
O
Serial data output to the DSP
6
DSP_MISO
I
Serial data input from the DSP
7
DSP_SPICLK
O
Serial data transfer clock signal output to the DSP
8
BYTE
I
External data bus width selection signal input terminal    “L”: 16 bit    Fixed at “L” in this set
9
CNVss
I
Processor mode selection signal input terminal    “L”: single chip mode    
Fixed at “L” in this set
10
DIR_XSTATE
I
Clock change status input from the digital audio interface receiver
11
DCACONOFF
I
Calibration microphone connection detection signal input terminal    
“H”: calibration microphone is connected
12
RESET
I
System reset signal input from the reset signal generator    “L”: reset    
For several hundreds msec. after the power supply rises, “L” is input, then it change to “H”
13
Xout
O
Main system clock output terminal (5 MHz)
14
Vss
-
Ground terminal
15
Xin
I
Main system clock input terminal (5 MHz)
16
Vcc1
-
Power supply terminal (+3.3V)
17
NMI
I
Non-maskable interrupt signal input terminal    Not used
18
DIR_ZERO
I
Zero data detection signal input from the digital audio interface receiver
19
DIR CSFLAG
I
Channel status 48 head bit update fl ag input from the digital audio interface receiver
20
DRIVE_OPC(DIAG)
I
Shut down signal input from the power amplifi er    “L”: shut down
21
PCM_MULTI
O
DSP input data selection signal output terminal    “L”: A/D converter data , “H”: LPCM data
22
CEC_DO
O
CEC serial data output to the HDMI connector
23
PCONT2
O
Power supply on/off control signal output terminal    “H”: power on
24
DIR_HCE
O
Chip enable signal output to the digital audio interface receiver
25
NO USE
O
Not used
26
DSP SPIDS
O
Device selection signal output to the DSP
27
DIR EEROR
I
Error detection signal input from the digital audio interface receiver    “H”: error
28
NO USE
O
Not used
29
I2C_CLK
I/O
Two-way I2C clock bus terminal    Not used
30
I2C_DATA
I/O
Two-way I2C data bus terminal    Not used
31
UCOM TX-DMP RX
O
Serial data output to the DMPORT connector
32
UCOM RX-DMP TX
I
Serial data input from the DMPORT connector
33
CLK1
O
Not used
34
S-AIR_SRC_MUTE
O
Sampling rate converter muting signal output terminal for wireless transmitter    Not used
35
UCOM TX-HDMI RX
O
Serial data output to the HDMI controller
36
UCOM RX-HDMI TX
I
Serial data input from the HDMI controller
37, 38
NO USE
O
Not used
39
PCONT3_SAIR
O
Power supply on/off control signal output terminal for wireless transmitter    Not used
40
ST_CE
O
Chip enable signal output to the tuner (FM/AM)
41
ST_CLK
O
Serial data transfer clock signal output to the tuner (FM/AM)
42
RDS_DATA
I
RDS serial data input from the tuner (FM/AM)
43
ST_DI
I
Serial data input from the tuner (FM/AM)
44
TUNED
I
Tuned detection signal input from the tuner (FM/AM)    “L”: tuned
45
ST_DO
O
Serial data output to the tuner (FM/AM)
46
DC_DET
I
Over load detection signal input terminal    “L”: over load
47
PCONT4_DSP
O
Power supply on/off control signal output terminal for DSP    “H”: power on
48
HDMI_MUTE
O
HDMI muting control signal output terminal
49
VOL_DOWN_A
I
Jog dial pulse signal input from the rotary encoder (A phase input) (for MASTER VOLUME)
50
PCONT1
O
Power supply on/off control signal output terminal    “H”: power on
51
TC74VHC153A
O
Digital audio input signal selection signal output terminal
52
VOLUME_UP
I
Jog dial pulse signal input from the rotary encoder (B phase input) (for MASTER VOLUME)
53
ROM_SDA
I/O
Two-way I2C data bus with the EEPROM
MAIN  BOARD  IC1005  R5F3640MDFAR (SYSTEM  CONTROLLER)
STR-KS100
46
Pin No.
Pin Name
I/O
Description
54
ROM_SCL
O
I2C clock signal output to the EEPROM
55, 56
NO USE
O
Not used
57
FL_CLK
O
Serial data transfer clock signal output to the fl uorescent indicator tube driver
58
CEC_STBY_LED
O
LED drive signal output terminal for ACTIVE STANDBY indicator    “H”: LED on
59
FL_LAT
O
Chip select signal output to the fl uorescent indicator tube driver
60
FL_D_OUT
O
Serial data output to the fl uorescent indicator tube driver
61
NO USE
O
Not used
62
Vcc2
-
Power supply terminal (+3.3V)
63
S-AIR RST
O
Reset signal output terminal for wireless transmitter    Not used
64
Vss
-
Ground terminal
65
NO USE
O
Not used
66
TC74VHC153B
O
Digital audio input signal selection signal output terminal
67
S-AIR GPIO2
I
Interrupt signal input terminal for wireless transmitter    Not used
68
DSP_INTR
I
Interrupt request signal input from the DSP
69
DIR RST
O
Reset signal output to the digital audio interface receiver
70
SAIR_ADC_SEL
O
A/D converter selection signal output terminal for wireless transmitter    Not used
71
S-AIR_DET
I
Wireless transmitter connection detection signal input terminal    Not used
72
DAMP_SOFT_MUTE
O
Soft muting on/off control signal output to stream processor    “L”: muting on
73
AC_CUT
I
AC cut detection signal input terminal    “L”: AC cut
74
POWER KEY
I
Wake-up signal (by power switch input) input terminal
75
RDS_CLK
I
RDS serial data transfer clock signal input from the tuner (FM/AM) 
76
DAMP_INIT
O
Reset signal output to the stream processor    “L”: reset
77
S-AIR_I2C_SDA
I/O
Two-way I2C data bus terminal for wireless transmitter    Not used
78
S-AIR_I2C_SCL
I/O
Two-way I2C clock bus terminal for wireless transmitter    Not used
79, 80
DAMP_LATCH2, 
DAMP_LATCH3
O
Serial data latch pulse signal output to the stream processor
81
DRIVE_RST(EN)
O
Reset signal output to the power amplifi er    “H”: reset
82
DAMP_LATCH1
O
Serial data latch pulse signal output to the stream processor
83, 84
OVERFLOW1,
OVERFLOW2
I
Overfl ow detection signal input from the stream processor    “L”: overfl ow
85
SAIR_SEL
O
Wireless transmitter output signal selection signal output terminal    Not used
86
BD3842DATA
O
Serial data output to the analog audio input selector
87
BD3842CLK
O
Serial data transfer clock signal output to the analog audio input selector
88
DSP_RST
O
Reset signal output to the DSP    “L”: reset
89
NO USE
O
Not used
90
KEY_0
I
Power switch input terminal
91
DMPORT_DET
I
Digital media port adapter connection detection signal input terminal    
“L”: digital media port adapter is connected
92
DESTINATION
I
Destination setting terminal
93
MODEL
I
Model setting terminal
94
HDMI_RST
O
Reset signal output to the HDMI controller    “L”: reset
95
AD KEY
I
INPUT SELECTOR switch input terminal
96
AVss
-
Ground terminal
97
PCONT_HDMI
O
Power supply on/off control signal output terminal for HDMI section    “H”: power on
98
Vref
I
Reference voltage (+3.3V) input terminal
99
AVcc
-
Power supply terminal (+3.3V)
100
DIR_HDOUT
I
Serial data input from the digital audio interface receiver
STR-KS100
47
HDMI  BOARD  IC3511  SII9013CLU (HDMI  RECEIVER)
Pin No.
Pin Name
I/O
Description
1
VSYNC
O
Vertical synchronize signal output for the HDMI transmitter
2 to 5
QO23 to QO20
-
Not used
6
IOGND
-
Ground terminal
7
IOVCC
-
Power supply terminal (+3.3V)
8 to 11
QO19 to QO16
-
Not used
12
CVCC18
-
Power supply terminal (+1.8V)
13
CGND
-
Ground terminal
14 to 17
QO15 to QO12
-
Not used
18
IOGND
-
Ground terminal
19
IOVCC
-
Power supply terminal (+3.3V)
20 to 23
QO11 to QO8
-
Not used
24
CVCC18
-
Power supply terminal (+1.8V)
25
CGND
-
Ground terminal
26 to 29
QO7 to QO4
-
Not used
30
IOGND
-
Ground terminal
31
IOVCC
-
Power supply terminal (+3.3V)
32 to 35
QO3 to QO0
-
Not used
36
CVCC18
-
Power supply terminal (+1.8V)
37
CGND
-
Ground terminal
38
CI2CA
-
Not used
39
CSDA
I/O
I2C two-way data bus with the EEPROM, HDMI transmitter and HDMI controller
40
CSCL
I
I2C clock signal input from the HDMI controller
41
DSDA
I/O
I2C two-way data bus with the HDMI input selector and EEPROM
42
DSDL
I
I2C clock signal input from the HDMI input selector
43
NC
-
Not used
44
PWR5V
I
Power supply voltage (+5V) input from the HDMI connector
45
CVCC18
-
Power supply terminal (+1.8V)
46
PGND
-
Ground terminal
47
PVCC
-
Power supply terminal (+3.3V)
48
PSVD
-
Not used
49
AVCC
-
Power supply terminal (+3.3V)
50
RXC-
I
TMDS clock signal input from the HDMI input selector
51
RXC+
I
TMDS clock signal input from the HDMI input selector
52
AGND
-
Ground terminal
53
AVCC
-
Power supply terminal (+3.3V)
54
RX0-
I
TMDS data input from the HDMI input selector
55
RX0+
I
TMDS data input from the HDMI input selector
56
AGND
-
Ground terminal
57
AVCC
-
Power supply terminal (+3.3V)
58
RX1-
I
TMDS data input from the HDMI input selector
59
RX1+
I
TMDS data input from the HDMI input selector
60
AGND
-
Ground terminal
61
AVCC
-
Power supply terminal (+3.3V)
62
RX2-
I
TMDS data input from the HDMI input selector
63
RX2+
I
TMDS data input from the HDMI input selector
64, 65
AGND, DGND
-
Ground terminal
66
DVCC18
-
Power supply terminal (+1.8V)
67
MUTE
O
HDMI muting control signal output terminal
68
IOVCC
-
Power supply terminal (+3.3V)
69
IOGND
-
Ground terminal
70
SPDIF
O
SPDIF signal output to the digital audio interface receiver and HDMI transmitter
71 to 74
SD3 to SD0
O
Serial data output to the DSP and HDMI transmitter
75
WS
O
L/R sampling clock signal output to the DSP and HDMI transmitter
76
SCK
O
Bit clock signal output to the DSP and HDMI transmitter
STR-KS100
48
Pin No.
Pin Name
I/O
Description
77
IOVCC
-
Power supply terminal (+3.3V)
78
IOGND
-
Ground terminal
79
MCLK
O
Master clock signal output to the DSP and HDMI transmitter
80
CGND
-
Ground terminal
81
CVCC18
-
Power supply terminal (+1.8V)
82
AUDPVCC18
-
Power supply terminal (+1.8V)
83
AUDPGND
-
Ground terminal
84
XTALOUT
O
System clock output terminal (28.322 MHz)
85
XTALIN
I
System clock input terminal (28.322 MHz)
86
ZTALVCC
-
Power supply terminal (+3.3V)
87
REGVCC
-
Power supply terminal (+3.3V)
88
RSVDL
-
Not used
89
RESET
I
Reset signal input from the HDMI controller    “L”: reset
90
SCDT
-
Not used
91
INT
O
Interrupt signal output to the HDMI controller
92 to 96
QE23 to QE19
O
Serial data output to the HDMI transmitter
97
IOGND
-
Ground terminal
98
IOVCC
-
Power supply terminal (+3.3V)
99 to 105
QE18 to QE12
O
Serial data output to the HDMI transmitter
106
IOGND
-
Ground terminal
107
IOVCC
-
Power supply terminal (+3.3V)
108 to 111
QE11 to QE8
O
Serial data output to the HDMI transmitter
112
CVCC18
-
Power supply terminal (+1.8V)
113
CGND
-
Ground terminal
114 to 117
QE7 to QE4
O
Serial data output to the HDMI transmitter
118
IOGND
-
Ground terminal
119
ODCK
O
Output data clock signal output to the HDMI transmitter
120
IOVCC
-
Power supply terminal (+3.3V)
121 to 124
QE3 to QE0
O
Serial data output to the HDMI transmitter
125
CVCC18
-
Power supply terminal (+1.8V)
126
CGND
-
Ground terminal
127
DE
O
Data enable signal output to the HDMI transmitter
128
HSYNC
O
Horizontal synchronize signal output to the HDMI transmitter
Page of 68
Display

Click on the first or last page to see other HT-SF100 / HT-SS100 / STR-KS100 service manuals if exist.

RANDOM: