Sony HT-FS1 / SA-FS1 / SS-FS1 Service Manual ▷ View online
SA-FS1/SS-FS1
5
SERVICE POSITION
IO board
HDMI board
MAIN board
POWER board
POWER board
C903
800
Ω/2W
Note 2: In checking the board, make
a capacitor discharge of C903
for electric shock prevention.
Note 3: Connect the IO board and the POWER board with the MAIN board when turning on power.
Otherwise, the IC of MAIN board is damaged, and the POWER board is protected.
Note 1: Take all board out from SA-FS1 and connect each board.
SA-FS1/SS-FS1
6
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Remote control
Here describes the buttons for amplifier
operation only. See page 30 for the buttons for
operation of the connected components.
operation only. See page 30 for the buttons for
operation of the connected components.
• Point the remote at the remote sensor
in the front
panel display.
• The 5,
), and
+ buttons have a tactile dot. Use
it as a guide during operation.
Note
Tip
1
2
3
4
6
7
8
0
ENTER
9
THEATRE
TV
AV
TV
BD
DVD
SAT
TOP MENU MENU
BD/DVD
RETURN/EXIT
TV
F1
F2
AMP MENU
CLEAR
DISPLAY
SOUND
FIELD
LEVEL
MODE
A/B
DIGITAL
ANALOG
DMPORT
+
G
O
R
P
-
G
O
R
P
'
(
H
G
)
.
N
9
Y
5
SYSTEM STANDBY
MENU/HOME
TOOLS/
OPTIONS
" (on/standby)
Press to turn the system on or off.
To save the power in standby mode
Press
while the system turns on.
To enter power saving mode, make sure that
the system is in the following status.
the system is in the following status.
– “CTRL: HDMI” is set to “CTRL OFF”
(page 25).
To cancel standby mode, press
once.
# Input buttons
Press one of the buttons to select the
component you want to use.
The buttons are factory assigned to control
Sony components. You can change the
factory settings of the input buttons to suit
the components in your system. For details,
refer to “Changing the input button
assignments of the remote” (page 33).
component you want to use.
The buttons are factory assigned to control
Sony components. You can change the
factory settings of the input buttons to suit
the components in your system. For details,
refer to “Changing the input button
assignments of the remote” (page 33).
$ SOUND FIELD
Press to select the sound field (page 24).
% LEVEL MODE
Press to adjust the level of the active
subwoofer (page 34).
subwoofer (page 34).
& AMP MENU
Press to display the menu of the system
(page 35).
(page 35).
'
(MUTING)
Press to turn off the sound.
(
+/–
Press to adjust the volume.
) $, 9, Y, D or
Press
$, 9, Y or D to select the settings.
Then press
to enter the selection.
Top panel (Active subwoofer)
" (on/standby)
Press to turn the system on or off.
# INPUT SELECTOR
Press to select the input source to play back.
$ VOLUME +/–
Press to adjust the volume level.
INPUT SELECTOR
-
VOLUME +
Front panel display (Active subwoofer)
About the indications in the front panel display
" POWER / ACTIVE STANDBY indicator
Lights as follows:
Green: The system is turned on.
Amber: Control for HDMI function is
working while the system is turned
off.
off.
Off:
The system is turned off, and the
Control for HDMI function is not
working.
Control for HDMI function is not
working.
# Audio decoding indicators
Lights up according to the audio input
signals.*
signals.*
* When “
PLII” lights up, S-Force PRO Front
Surround is applied after Dolby Pro Logic II.
$ SLEEP (38)
Flashes when the sleep timer function is
active.
active.
% HDMI (13, 40)
Lights up when HDMI equipment is in use.
& COAX/OPT
Lights up according to the cable that you are
using.
using.
' Remote sensor
Point the remote here.
POWER /
ACTIVE STANDBY
SA-FS1/SS-FS1
7
SECTION 3
DISASSEMBLY
•
This set can be disassembled in order shown below.
3-1. FRONT
PANEL
ASSY
(Page
8)
SET
3-3. AMP
BLOCK
(Page
10)
3-4. IO
BOARD
(Page
10)
3-2. GRILLE
ASSY
(Page
9)
3-5. HDMI
BOARD
(Page
11)
3-6. BACK
PANEL,
D.C. FAN (M3001)
(Page
11)
3-7. MAIN
BOARD
(Page
12)
3-8. POWER
BOARD
(Page
12)
SA-FS1/SS-FS1
8
3-1. FRONT PANEL ASSY
Note: Follow the disassembly procedure in the numerical order given.
wire (flat type) (15 core)
(CN801)
(CN801)
sheet (wire vibration proof)
Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
Insert the jig (J-2501-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
Raise the front panel assy a little by little
from bottom to top of the set.
eight bosses
bottom side
Insert a flat-tip screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
two screws
(BVTP3
(BVTP3
× 8)
two screws
(BVTP3
(BVTP3
× 8)
R front panel assy
retainer board
retainer board
ferrite core
Note: Please do set by placing the grille assy side up as shown in the fi gure and work.
Click on the first or last page to see other HT-FS1 / SA-FS1 / SS-FS1 service manuals if exist.