Sony HT-DDW2500 / STR-KM2500 Service Manual ▷ View online
STR-KM2500
9
3-3. BACK PANEL BLOCK
3-4. FRONT PANEL BLOCK
screw
(BVTP3
× 8)
RB five screws
(BVTP3
× 8)
RT screw (BVTP3 × 8)
four screws
(BVTP3
× 8)
screw
(BVTP3
× 8)
clamp
RE back panel block
wire (flat type) (17 core)
(CNS513)
three connectors
(CNP902, CNP910, CNP913)
connector (CNP506)
connector
(CNP512)
connector (CNP505)
connector
(CNP912)
five screws
(BVTP3
× 8)
two connectors
(CNP430,
CNP930)
two leads (with connector)
(TP790,
TP2000)
connector
(CNP790)
claw
claw
front panel section
STR-KM2500
10
3-5. MAIN BLOCK
3-6. MAIN BOARD
two screws
(BV3)
main block
three screws
(BV3)
two connectors
(CNP430,
CNP930)
two connectors
(CNP922,
CNP940)
connector
(CNP790)
two screws
(BVTP3
× 8)
MAIN board
heatsink assy
Remove the
eighteen
solders
six screws
(transistor)
three transistor MN2488-OPY-MK
(Q753, Q603, Q703)
three transistor MP1620-OPY-MK
(Q754, Q604, Q704)
screw
(BV3)
wire route board
six sheets
STR-KM2500
11
SECTION 4
TEST MODE
FL CHECK MODE
All fl uorescent segments are tested. When this test is activated,
all segments turn on at the same time, then each segment turns on
one after another.
Procedure:
1. When pressing the [INPUT MODE] and [TUNING MINUS]
All fl uorescent segments are tested. When this test is activated,
all segments turn on at the same time, then each segment turns on
one after another.
Procedure:
1. When pressing the [INPUT MODE] and [TUNING MINUS]
buttons, press the [
?/1
] button to turn on the main power.
2. All segments turn on.
3. Turn the [INPUT SELECTOR] dial.
4. Test pattern 1 turn on.
4. Test pattern 1 turn on.
5. Turn the [INPUT SELECTOR] dial once again.
6. Test pattern 2 turn on.
6. Test pattern 2 turn on.
7. Turn the [INPUT SELECTOR] dial once again. All segments
turn off.
8. Every turning of the [INPUT SELECTOR] dial turns on each
segment one after another on the same order.
S.F. CLEAR MODE
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [A.F.D] button, press the [
The preset sound fi led is cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [A.F.D] button, press the [
?/1
] button to
turn on the main power.
2. The message “S.F. CLR.” appears and initialization is per-
formed.
VERSION CHECK MODE
When this mode is used the model, the destination and the soft-
ware version number are displayed.
Procedure:
1. While pressing the [INPUT MODE] and [TUNING MODE]
When this mode is used the model, the destination and the soft-
ware version number are displayed.
Procedure:
1. While pressing the [INPUT MODE] and [TUNING MODE]
buttons, press the [
?/1
] button to turn on the main power.
2. The model, the distination and the software version number
appear.
KEY CHECK MODE
This mode is used to check the key.
Procedure:
1. While pressing the [INPUT MODE] and [MUSIC] buttons,
This mode is used to check the key.
Procedure:
1. While pressing the [INPUT MODE] and [MUSIC] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “REST 08” appears.
3. Every pressing of any button other than the [
3. Every pressing of any button other than the [
?/1
] button
counts down the buttons. The buttons which are already
counted once are not counted again.
counted once are not counted again.
4. When all buttons are pressed, the message “REST 00” ap-
pears.
SWAP ALL MODE
The signal will be swapped to all channels so that all speakers
will have sound output.
Procedure:
1. While pressing the [TUNING MODE] and the [DISPLAY]
The signal will be swapped to all channels so that all speakers
will have sound output.
Procedure:
1. While pressing the [TUNING MODE] and the [DISPLAY]
buttons simultaneously, press the power [
?/1
] button to turn
on the main power.
2. The message “SWP.ALL” appears.
SHIPMENT MODE
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TUNING MINUS] and [DISPLAY] buttons,
All preset contents are cleared when this mode is activated. Use
this mode before returning the product to clients upon completion
of repair.
Procedure:
1. While pressing the [TUNING MINUS] and [DISPLAY] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “CLEARING” appears.
MEMORY
L
C
R
SL
S
SR
SB SBR
SBL
SW
LFE
SP A
SP B
SP B
CAT
NEO:6
SAT
D.RANGE
RDS ST
MONO
DTS-ES
96 / 24
HDMI
COAX
D EX
OPT
PL II x
PL
dB
k Hz
mft.
MHz
L
R
S
LFE
SP B
NEO:6
D.RANGE
RDS ST
MONO
COAX
PL II x
k
m
MHz
MEMORY
C
SL
SR
SB SBR
SBL
SW
CAT
DTS
D
PL
dB
Hz
ft.
ST
STR-KM2500
12
SECTION 5
ELECTRICAL CHECK
FM AUTO STOP CHECK
signal
generator
set
Procedure:
1. Turn on the set.
2. Input the following signal from signal generator to FM an-
1. Turn on the set.
2. Input the following signal from signal generator to FM an-
tenna input directly.
Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation
Deviation
: 75 kHz
Modulation
: 1 kHz
ANT input
: 1 kHz
Note: Use 75 ohm coaxial cable to connect signal generator and the set.
You cannot use video cable for checking.
Use signal generator whose output impedance is 75 ohm.
3. Set to FM tuner function and scan the input FM signal with
automatic scanning.
4. Confi rm that input frequency of A, B and C are detected and
automatic scanning stops.
When the station signal is received in good condition, automatic
scanning stops.
scanning stops.
RE-BOX CLASSIFICATION TEST MODE
Procedure:
1. While pressing the [MOVIE] and [DISPLAY] buttons, press
Procedure:
1. While pressing the [MOVIE] and [DISPLAY] buttons, press
the [
?/1
] button to turn on the main power.
2. The message “R.BOX[][][]XX” appears.
XX: times set powered on
VACS CONTROL TEST MODE
The VACS feature of the amplifi er is turned off purposely.
Procedure:
1. While pressing the [INPUT MODE] and [MOVIE] buttons,
The VACS feature of the amplifi er is turned off purposely.
Procedure:
1. While pressing the [INPUT MODE] and [MOVIE] buttons,
press the [
?/1
] button to turn on the main power.
2. The message “VACS OFF” appears.
AM CHANNEL STEP 9 kHz/10kHz SELECTION MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
[
Turn the [INPUT SELECTOR] control to set AM and press the
[
?/1
] button to turn off the main power.
While depressing the [TUNING MODE] button, press the [
?/1
]
button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
History Mode
* The state that the set is used is memorized.
* Procedure:
* Procedure:
1. While depressing the [INPUT MODE] and the [A.F.D.]
buttons simultaneously, press the [
?/1
] button to turn on the
main power.
2. “HISTORY”
appears.
3. Each time the [
r
] / [
R
] buttons on the remote commander is
pressed, the item is switched in order as follows.
Items
Display
Protector Count
COUNT XX
Total single power on time
SXXXHXXM
Sound Field
SND FLD
Input function
FUNCTION
Input Mode
INP MODE
Digital Select
DIGI IN
Stream information
STREAM
Signal confi guration
CO XXXXX
Headphones
HP XXX
Volume
VOL XXX
Bass Setting
BASS XXX
Treble Setting
TREB XXX
Front Level Setting
F XXX
Subwoofer Level Setting
SW XXX
Total power on time
TXXXHXXM
Muting Status
MUTE XXX
Power on counter (Rebox test mode)
P.W. XXX
Click on the first or last page to see other HT-DDW2500 / STR-KM2500 service manuals if exist.