Sony HT-7100DH / STR-K7100 Service Manual ▷ View online
9
STR-K7100
2-2. BACK PANEL SECTION
2-3. FRONT PANEL SECTION
qa
three screws
(+BVTP 3
×
8)
qs
five screws
(+BVTP 3
×
8)
qd
three screws
(+BVTP 3
×
8)
9
three screws
(+BVTP 3
×
8)
0
screw
(+BVTP 3
×
8)
qf
screw
(+BVTP 3
×
8)
qg
back panel section
1
CNP901 (2P)
2
CNP202 (3P)
3
CNP203 (3P)
5
CNP103 (3P)
7
wire (flat type) (9 core)
(CNS507)
8
wire (flat type) (13 core)
(CNS510)
6
wire (flat type) (9 core)
(CNS503)
4
wire (flat type) (5 core)
(CN102)
6
five screws
(+BVTP 3
×
8)
1
CNP790 (4P)
7
front panel section
3
CNP507 (3P)
4
CN506 (3P)
5
CNP503 (3P)
2
wire (flat type) (17 core)
(CNS511)
10
STR-K7100
2-4. DIGITAL BOARD
2-5. MAIN BOARD SECTION
4
screw
(+BVTP 3
×
8)
5
DIGITAL board
1
CNP505 (7P)
3
CNP512 (3P)
2
CNP503 (8P)
7
two screws
(+BV3 (3
-CR))
8
MAIN board section
6
two screws
(+BV3 (3
-CR))
5
screw
(+BV3 (3
-CR))
1
CNP801 (5P)
2
CNP802 (5P)
3
CNP912 (2P)
4
CN915 (6P)
11
STR-K7100
2-6. STANDBY BOARD
5
STANDBY board
2
CNP804 (3P)
3
CNP805 (3P)
1
CNP902 (2P)
4
screw
(+BVTP 3
×
8)
12
STR-K7100
SECTION 3
TEST MODE
AM CHANNEL STEP 9 kHz/10 kHz SELECTION
MODE
MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
* Procedure:
Turn the [INPUT SELECTOR] control to set AM and press the
?/1
button to turn off the main power.
While depressing the [TUNING MODE] button, press the
?/1
button to turn on the main power.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
Either the message “9k STEP” or “10k STEP” appears for a
moment and select the desired step.
VACUUM FLUORESCENT DISPLAY TEST MODE
* All fluorescent segments are tested.
When this test is activated, all segments light on at the same
time, then each segment lights on one after another.
time, then each segment lights on one after another.
* Procedure:
While depressing the [TUNING MODE] and the [DISPLAY] but-
tons simultaneously, press the
tons simultaneously, press the
?/1
button to turn on the main
power.
1. ALL segments light on.
2. Turn the [INPUT SELECTOR] control, confirm display.
3. Turn the [INPUT SELECTOR] control, confirm display.
4. Turn the [INPUT SELECTOR] control, all segments light off.
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
completion of repair.
* Procedure:
While depressing the [2CH] button, press the
?/1
button to turn
on the main power.
The message “S.F. CLR.” appears for a moment and initializa-
tion is performed.
The message “S.F. CLR.” appears for a moment and initializa-
tion is performed.
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
* Procedure:
While depressing the [SPEAKERS $OFF/A/B%] and the [DISPLAY]
buttons simultaneously, press the
buttons simultaneously, press the
?/1
button to turn on the
main power.
The model name, destination and the software version are dis-
played for a moment.
The model name, destination and the software version are dis-
played for a moment.
KEY CHECK MODE
* Button check
* Procedure:
* Procedure:
While depressing the [SPEAKERS $OFF/A/B%] and the [2CH] but-
tons simultaneously, press the
tons simultaneously, press the
?/1
button to turn on the main
power.
Either the message “REST 13” appears.
Every pressing of any button other than the
Either the message “REST 13” appears.
Every pressing of any button other than the
?/1
counts down
the buttons. The buttons which are already counted once are not
counted again. When all buttons are pressed “REST 00” appears.
counted again. When all buttons are pressed “REST 00” appears.
SWAP ALL MODE
* The signal will be swap to all channel so that all speaker will
have sound output.
* Procedure:
1. While depressing the [SPEAKERS $OFF/A/B%] and the [A.F.D.]
1. While depressing the [SPEAKERS $OFF/A/B%] and the [A.F.D.]
buttons simultaneously, press the power
?/1
button to turn on
the main power.
2. “SWAP” appears. (No change while displayed.)
SHIPMENT MODE
All preset contents are reset to the default setting.
* Procedure:
1. While depressing the [SPEAKERS $OFF/A/B%] and the [MUSIC]
* Procedure:
1. While depressing the [SPEAKERS $OFF/A/B%] and the [MUSIC]
buttons simultaneously, press the power
?/1
button to turn on
the main power.
2. “CLEARED” appears and switch off the set.
DCAC FACTORY TEST MODE
DCAC Factory Test mode have two stages:
1. DCAC DSP Data Line Checking
2. DCAC board Checking
1. DCAC DSP Data Line Checking
2. DCAC board Checking
Factory Test System Setup
1. When power off:
Press the three buttons [MEMORY/ENTER] + [MOVIE] +
?/1
.
“DCAC[]FTM” appears.
Afterward, press the [TUNING MODE] to start DCAC factory
test mode.
Afterward, press the [TUNING MODE] to start DCAC factory
test mode.
L
SW
C
R
SL
S
SR
SBL
SB SBR
LFE
SP A
NEO:6
COAX
HDMI
DEX
DTS -ES
x
II
PL
RDS ST
CAT
96/24
MONO
D.RANGE
SAT
D D
D D
PL OPT
D D
dB
Hz
k
ft.
m
MHz
MEMORY
SP B
LFE
NEO:6
COAX
x
RDS
MONO
D.RANGE
k
m
MHz
SP B
SW
C
SL
SR
SBL
SB SBR
D
DTS
ST
CAT
D D
PL
D D
dB
Hz
ft.
MEMORY
DSP Data Line
Check
Start
Pass
Pass
Auto Cal Mic
Check
END
SPK Front Left
DCAC MIC
Receiver
Click on the first or last page to see other HT-7100DH / STR-K7100 service manuals if exist.