Sony HS-KP1 Service Manual ▷ View online
HS-KP1
5
Connecting the cables and installing the unit into the wall
1
While pushing the tab at the bottom of the unit, remove the cover
panel. (The cover panel and unit are factory-packed separately.)
panel. (The cover panel and unit are factory-packed separately.)
2
Attach RJ45 connectors to the ends of the CAT5 cables.
For details, see “Connecting RJ45 connectors to CAT5 cables.”
3
Connect the units using the CAT5 cables.
For details, see “Connecting speaker cords or power supply cords” and “Part names and descriptions.”
4
Insert the rear of the unit into the 2 gang J-box, and insert the two
tabs on the top of the unit into the holes of the wall mounting
bracket. Then fasten the bottom part of the unit with the screws
(supplied) with the wall mounting bracket.
tabs on the top of the unit into the holes of the wall mounting
bracket. Then fasten the bottom part of the unit with the screws
(supplied) with the wall mounting bracket.
Screws for the unit (short)
5
Hook the cover panel on the two tabs on the top of the unit first,
and then push the bottom part until the panel clicks into place.
and then push the bottom part until the panel clicks into place.
Cover panel
Installing the Unit
Before installing the unit into the wall, take steps to ensure your safety and that of your surroundings. Check the
following:
● You can connect speakers (nominal impedance 8 ohms or higher) to the unit. For details, see “Connecting
following:
● You can connect speakers (nominal impedance 8 ohms or higher) to the unit. For details, see “Connecting
speaker cords or power supply cords.”
● The necessary wiring such as CAT5 cables, speaker cords, power supply cords, or IR REMOTE cords varies
depending on your system.
● The location of the speakers to make sure that speaker cords can be run between the unit and the speakers.
● The durability of the wall. The thickness of the wall must be between 13 to 19 mm (
● The durability of the wall. The thickness of the wall must be between 13 to 19 mm (
1
/
2
to
3
/
4
inches).
● There are no obstructions, such as air, electrical, or water conduit near the location where the unit is installed.
● There is enough space (over 15 cm (6 inches)) inside the wall. If the space available inside the wall is insufficient
● There is enough space (over 15 cm (6 inches)) inside the wall. If the space available inside the wall is insufficient
or does not have proper ventilation, a malfunction of the unit may occur due to heat build-up.
● Do not install the unit where it may get wet due to water or other liquids. This may cause a malfunction of the
unit.
● Do not install the unit in a place where moisture condensation may cause a malfunction of the unit.
Installing a 2 gang J-box in a new construction
Be sure to install a 2 gang J-box on a stud before wall construction is finished, so that the unit can be placed in the
2 gang J-box after construction of the wall is finished.
2 gang J-box after construction of the wall is finished.
Sony recommends:
Carlon
®
gang boxes
Part No.
Description
BH235A, SC200A
2 gang J-box with nails
BH235S
2 gang J-box with screws
1
Prewire the CAT5 cables in the walls.
2
Place the 2 gang J-box on a stud, and then fasten it with the nails
or screws that came with the 2 gang J-box.
or screws that came with the 2 gang J-box.
2 gang J-box
3
Run the CAT5 cables through the holes of the 2 gang J-box.
Note
Do not pull the cable in longer than necessary. The unit may not be placed in the 2 gang J-box because of the
extra length of the cable.
extra length of the cable.
4
Cut a hole of 110 to 116 mm (4
3
/
8
to 4
5
/
8
inches) in width and 98
to 104 mm (3
7
/
8
to 4
1
/
8
inches) in length in the wall material. Then
attach it to the structure of the house, and finish the wall.
5
Place the wall mounting bracket (supplied) in the hole of the
finished wall, and then fasten it with screws (supplied) to the 2
gang J-box.
finished wall, and then fasten it with screws (supplied) to the 2
gang J-box.
Wall mounting bracket
Screws for the wall
mounting bracket (long)
mounting bracket (long)
Connecting RJ45 connectors to CAT5 cables
Before you connect the CAT5 cables to the unit, you need to connect the RJ45 connectors to each end of the
cables.
Be sure to use Category 5e straight-through cables, and the wiring connection is correct. See the illustration below
for details on connections.
cables.
Be sure to use Category 5e straight-through cables, and the wiring connection is correct. See the illustration below
for details on connections.
CAT5 cable
White/Orange
Wire color
Orange
White/Green
Blue
White/Blue
Green
White/Brown
Brown
1
Pin No.
2
3
4
5
6
7
8
Note on installing CAT5 cables
The following lengths of cable(s) can extend up to 200 feet:
● The combined length of the two longest cables connecting the Distribution Panel (HS-MB1) to an AV Wall Port
(HS-WV1) and a Keypad (this unit).
● The length of cable connecting an AV Wall Port (HS-WV1) directly to a Keypad (this unit) without connecting
the Distribution Panel (HS-MB1).
● The length of cable connecting a Local Audio Wall Port (HS-WA1) to a Keypad (this unit).
HS-KP1
6
SECTION 3
DISASSEMBLY
3-1. REAR CASE SECTION, FRONT PANEL SECTION
Note: Follow the disassembly procedure in the numerical order shown below.
•
This set can be disassembled in the order shown below.
3-1.
REAR CASE SECTION,
FRONT PANEL SECTION
(Page
6)
3-2.
KP SWITCH BOARD
(Page
7)
SET
3-3.
KP LCD BOARD
(Page
7)
3-4. LCD
MODULE
(Page
8)
3-5. SPEAKER
ASSY
(Page
8)
3-6. BOARDS
SECTION
(Page
9)
3-7.
KP RJ45 BOARD,
KP CHUKEI BOARD,
KP DAMP BOARD,
KP POWER BOARD
(Page
9)
three screws
(+BTP
(+BTP
2
× 8)
five screws
(+BTP
(+BTP
2
× 8)
rear case section
front panel section
wire (flat type) (11 core)
(CN2503)
(CN2503)
wire (flat type) (20 core)
(CN3601)
(CN3601)
wire (flat type) (16 core)
(CN3602)
(CN3602)
HS-KP1
7
3-2. KP SWITCH BOARD
3-3. KP LCD BOARD
three screws
(+BTP
(+BTP
2
× 8)
four screws
(+BTP
(+BTP
2
× 8)
two screws
(+BTP
(+BTP
2
× 8)
KP SWITCH board
wire (flat type) (10 core)
(CN3605)
(CN3605)
shield plate
wire (flat type) (40 core)
(CN2501)
(CN2501)
two claws
KP LCD board
claw
claw
HS-KP1
8
3-4. LCD MODULE
LCD module
front panel complete assy
panel base assy
FPC core
3-5. SPEAKER ASSY
two screws
(+BTP
(+BTP
2
× 8)
two screws
(+BTP
(+BTP
2
× 8)
terminal (+) (blue/gray)
terminal (–) (gray)
speaker assy
Click on the first or last page to see other HS-KP1 service manuals if exist.