DOWNLOAD Sony HCD-VZ10 Service Manual ↓ Size: 8.83 MB | Pages: 92 in PDF or view online for FREE

17

[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:

The aging operation stops and display status.

• If no error occurs:

The aging operation continues repeatedly.

1.

Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray.  Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x ,  DISPLAY  , and  DISC 4  simultaneously.
4) Aging operations of CD and tape are started at the same time.

• Tape Deck
1.

The tape in deck A is rewound. “TAPE A AG-1” is displayed.

2.

The FWD side of deck A is played for two minutes.
“TAPE A AG-2” is displayed.

3.

The tape in deck A is fast forwarded. “TAPE A AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

4.

The RVS side of deck A is played for two minutes.
“TAPE A AG-4” is displayed.

5.

The tape in deck A is rewound. “TAPE A AG-5” is displayed.

6.

The FWD side of deck B is played for two minutes.
“TAPE B AG-2” is displayed.

7.

The tape in deck B is fast forwarded. “TAPE B AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.

8.

The RVS side of deck B is played for two minutes.
“TAPE B AG-4” is displayed.

9.

The tape in deck A is rewound. “TAPE A AG-5” is displayed.

10. Repeated from step 2.

• CD
1.

The tray rotates.

2.

DISC 5 is chucked.

3.

The TOC is read.

4.

The first track is played for 3 seconds.

5.

The last track is played for 3 seconds.

6.

DISC 1 is open.

7.

DISC 1 is close.

8.

Repeated from step 2.

18

2. Correction of Errors
[When due to tape deck]
Stopped while tape aging operation with the “  ” displayed state.

[When due to CD]
Press  x ,  DISPLAY , and  Z  together to display the error code.

• Display of number of mechanism errors

Move the stick to the left and right to display “CDM Err Count *”.
* is the number of mechanism errors.

• Display of mechanism error

Move the stick to the left and right to display “CDM E**D##$$%%!!”.
Move the stick up and down to send the error number.

**

: Error number 00 is the latest error.

The larger the number, the older will the error be. (Maximum 9)

##

: FF is the mechanism error after mechanism initialization ends.

$$

: Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 1 or 2, it indicates mechanism error in tray loading between the stocker position and behind it.

%% : Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 2, it indicates mechanism error in the up/down movements of the stocker.

!!

: Judge from the first digit of the error number. (Don’t care the second digit.)

When the error number is 2, it indicates mechanism error during switching of the clamper and mode.

• No DISC error display

Move the stick left and right to display “No Disc Count *”.
* means the number of no discs.

• No DISC error display

Move the stick left and right to display “No E**D##$$%%00”.
Move the stick up and down to send the error number.

**

: Error number 01 is the latest error.

The larger the number, the older will the error be. (Maximum 3)

##

: 01 .... FOCUS ERROR

02 .... GFS ERROR
03 .... SET UP ERROR

$$

: 00 .... Judged as No DISC without attempting chucking retry

02 .... Judged as No DISC after chucking retry

%% : Judged with the first digit of the error number in the state where No DISC has been determined.

(Don’t care the second digit.)
1 ...... STOP
2 ...... SET UP
3 ...... TOC Read
4 ...... Access
5 ...... PLAY
6 ...... PAUSE
7 ...... Manual Search (during PLAY)
8 ...... Manual Search (during PAUSE)

3. Ending the Aging Mode
1) End the Aging Mode with the power off.
2) To reset the CD error history, be sure to perform cold reset.

19

On this mode, the data of the color-bars signal as a picture signal and the 1kHz sine wave signal as a sound signal are output by the
mechanism control microcomputer (IC502) for video CD signal check. When measurement of the voltage and waveform on the VIDEO
board, perform it in this mode.
For reference, the color-bars signal can be observed at J302 (VIDEO OUT) and the sound signal can be observed at J101 (VIDEO/MD
(AUDIO) OUT) using an oscilloscope.
1.

Connect the lead wire to both ends of the land of SL503 of the VIDEO board.

2.

Press the  ?/1  button to turn ON the power. Press  FUNCTION  button to select CD.

3.

After 2 or 3 seconds later, connect the lead wire.

4.

After measuring, remove the lead wire connected.

20

3.04 – 6.96 N • m

(31 to 71 g • cm)

(0.43 – 0.98 oz • inch)

0.20 – 0.58 N • m

(2 to 6 g • cm)

(0.02 – 0.08 oz • inch)

3.04 – 6.96 N • m

(31 to 71 g • cm)

(0.43 – 0.98 oz • inch)

0.20 – 0.58 N • m

(2 to 6 g • cm)

(0.02 – 0.08 oz • inch)

6.97 – 14.02 N • m

(71 to 143 g • cm)

(0.98 – 1.99 oz • inch)

0.98 N • m or more

(100 g or more)

(3.53 oz or more)

0.98 N • m or more

(100 g or more)

(3.53 oz or more)

CQ-102C

CQ-102C

CQ-102RC

CQ-102RC

CQ-201B

CQ-403A

CQ-403R

Precaution
1. Clean the following parts with a denatured alcohol-moistened

swab:

record/playback heads

pinch rollers

erase head

rubber belts

capstan

idlers

2. Demagnetize the record/playback head with a head demagne-

tizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the

parts adjusted.

5. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

Note: Perform this adjustments for both decks.

Procedure:
1. Mode : Playback

Signal

Used for

Tape

Mode

FWD

FWD
back tension

REV

REV
back tension

FF/REW

FWD tension

REV tension

Torque meter

Meter reading

1. Demagnetize the record/playback head with a head demagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjusted.

4. The adjustments should be performed with the rated power sup-

ply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in this

service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit adjust-
ment.)

6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise

specified.

P-4-A100

WS-48B

P-4-L300

10 kHz, –10 dB

3 kHz, 0 dB

315 Hz, 0 dB

Azimuth Adjustment

Tape Speed Adjustment

Level Adjustment

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.

main board
CN301
Pin 1 (R-ch)
Pin 3 (L-ch)