Sony HCD-VX5AJ / MHC-VX5 / MHC-VX5J / MHC-VX7 Service Manual ▷ View online
– 17 –
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.
so that outputs match within 1dB of peak.
3. Mode: Playback
4. Repeat step 1 to 3 in playback (REV) mode.
5. After the adjustments, apply suitable locking compound to the
5. After the adjustments, apply suitable locking compound to the
pats adjusted.
Adjustment Location: Playback Head (Deck A).
Record/Playback/Erase Head (Deck B).
Screw
position
position
L-CH
peak
peak
within
1dB
1dB
Output
level
level
L-CH
peak
peak
R-CH
peak
peak
within
1dB
1dB
Screw
position
position
R-CH
peak
peak
set
test tape
P-4-A100
(10 kHz, – 10 dB)
P-4-A100
(10 kHz, – 10 dB)
R-CH
oscilloscope
L-CH
R-CH
V
H
waveform of oscilloscope
in phase 45
°
90
°
135
°
180
°
good
wrong
MAIN board
MD OUT jack (J101)
L-CH
MD OUT jack (J101)
L-CH
Tape Speed Adjustment
DECK B
Mode: Playback
1. Insert the WS-48B into the deck B.
2. Press the
2. Press the
( button on the deck B.
3. Press the
[HI-DUB]
button in playback mode.
Then at HIGH speed mode.
4. Adjust RV1001 on the LEAF SW board do that frequency
counter reads 6,000 ± 180 Hz.
5. Press the
[HI-DUB]
button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
counter reads 3,000 ± 90 Hz.
Adjustment Location: LEAF SW board
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
Sample value of Wow and Flutter: 0.3% or less W.RMS (JIS)
(WS-48B)
Playback level Adjustment
DECK A DECK B
Procedure:
Mode: Playback
Mode: Playback
Deck A is RV311 (L-CH) and RV411 (R-CH), Deck B is RV301
(L-CH) and RV401 (R-CH) so that adjustment within specifica-
tion values as follows.
(L-CH) and RV401 (R-CH) so that adjustment within specifica-
tion values as follows.
Specification Values:
J101 PB level: 301.5 to 338.3 mV (– 8.2 to – 7.2 dB) level
difference between the channels: within ± 0.5 dB
difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
forward
reverse
+
–
–
set
test tape
WS-48B
(3 kHz, 0 dB)
WS-48B
(3 kHz, 0 dB)
MAIN board
MD OUT jack (J101)
L-CH, R-CH
MD OUT jack (J101)
L-CH, R-CH
frequency counter
+
–
–
set
test tape
P-4-L300
(315 Hz, 0 dB)
P-4-L300
(315 Hz, 0 dB)
MAIN board
MD OUT jack (J101)
L-CH, R-CH
MD OUT jack (J101)
L-CH, R-CH
level meter
– 18 –
REC Bias Adjustment
DECK B
Procedure:
1. Mode: Record
1. Mode: Record
FUNCTION: VIDEO
2. Mode: Playback
3. Confirm playback the signal recorded in step 1 become speci-
fication values as follows.
If these values are out of specification values, adjust the RV341
(L-CH) and RV441 (R-CH) on the AUDIO board to repeat
steps 1and 2.
If these values are out of specification values, adjust the RV341
(L-CH) and RV441 (R-CH) on the AUDIO board to repeat
steps 1and 2.
Specification values: Playback output of 315 Hz to playback
output of 10 kHz: ± 0.5 dB
Adjustment Location: AUDIO board
REC Level Adjustment
DECK B
Procedure:
1. Mode: Record
1. Mode: Record
FUNCTION: VIDEO
2. Mode: Playback
3. Confirm playback the signal recorded in step 1 become speci-
fication values as follows.
If these values are out of specification values, adjust the RV301
(L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
1 and 2.
If these values are out of specification values, adjust the RV301
(L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
1 and 2.
Specification values:
J101 PB level: 47.2 to 53.0 mV (– 24.3 to – 23.3 dB)
J101 PB level: 47.2 to 53.0 mV (– 24.3 to – 23.3 dB)
Adjustment Location: MAIN board
– MAIN BOARD (Conductor Side) –
– AUDIO BOARD (Component Side) –
– LEAF SW BOARD (Component Side) –
attenuator
set
MAIN board
VIDEO (AUDIO) IN jack (J101)
L-CH, R-CH
VIDEO (AUDIO) IN jack (J101)
L-CH, R-CH
1) 315 Hz
2) 10 kHz
2) 10 kHz
50 mV (– 23.8 dB)
600
Ω
blank tape
CN-123
CN-123
AF OSC
+
–
–
set
recorded
portion
portion
MAIN board
MD OUT jack (J101)
L-CH, R-CH
MD OUT jack (J101)
L-CH, R-CH
level meter
set
MAIN board
VIDEO (AUDIO) IN jack (J101)
L-CH, R-CH
315 Hz, 50 mV (– 23.8 dB)
VIDEO (AUDIO) IN jack (J101)
L-CH, R-CH
315 Hz, 50 mV (– 23.8 dB)
blank tape
CS-123
CS-123
600
Ω
attenuator
AF OSC
+
–
–
set
recorded
portion
portion
MAIN board
MD OUT jack (J101)
L-CH, R-CH
MD OUT jack (J101)
L-CH, R-CH
level meter
RV301
L
RV351
R
IC301
REC LEVEL
J101
VIDEO (AUDIO) IN
(L/R)
MD OUT
(L/R)
RV401
RV301
RV341
RV311
RV411
IC602
CN601
L
R
R L
RV441
PB LEVEL
– DECK B –
REC BIAS
L
R
PB LEVEL
– DECK A –
TAPE SPEED
RV1002
RV1001
(NORMAL) (HIGH)
CN1001
– 19 –
– 20 –
Note:
1. CD Block is basically designed to operate without adjustment. There-
fore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10 M
3. Use an oscilloscope with more than 10 M
Ω
impedance.
4. Clean the object lens by an applicator with neutral detergent when the
signal level is low than specified value with the following checks.
S-Curve Check
Procedure:
1. Connect oscilloscope to TP (FE).
2. Connect between TP (FE1) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
4. Turn the power ON.
5. Load a disc (YEDS-18) and actuate the focus search. (In con-
1. Connect oscilloscope to TP (FE).
2. Connect between TP (FE1) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
4. Turn the power ON.
5. Load a disc (YEDS-18) and actuate the focus search. (In con-
sequence of open and close the disc tray, actuate the focus
search)
search)
6. Cofirm that the oscilloscope waveform (S-curve) is symmetri-
cal between A and B. And confirm peak to peak level within
4 ± 1 Vp-p.
4 ± 1 Vp-p.
S-curve waveform
7. After check, remove the lead wire connected in step 2 and 3.
Note:
• Try to measure several times to make sure than the ratio of A : B
or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the brightness
to obtain best waveform.
RF Level Check
Procedure:
1. Connect oscilloscope to TP (RF).
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3. Turn the power ON.
4. Load a disc (YEDS-18) and press the
1. Connect oscilloscope to TP (RF).
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3. Turn the power ON.
4. Load a disc (YEDS-18) and press the
^ button to play.
5. Confirm that the oscilloscope waveform is clear and check RF
signal level is correct or not.
6. After check, remove the lead wire connected in step 2.
Note:
Clear RF signal waveform means that the shape “≈” can be clearly
distinguished at the center of the waveform.
distinguished at the center of the waveform.
CD SECTION
+
–
–
BD board
TP (FE)
TP (VC)
TP (VC)
oscilloscope
A
B
symmetry
within 4
±
1 Vp-p
+
–
–
BD board
TP (RF)
TP (VC)
TP (VC)
oscilloscope
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
TIME/DIV: 500 ns
level:
1.45
1.45
±
0.3 Vp-p
E-F Balance (1 Track Jump) Check
Procedure :
1. Connect oscilloscpe to TP (TE) and TP (VC).
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the
1. Connect oscilloscpe to TP (TE) and TP (VC).
2. Turn the power ON.
3. Load a disc (YEDS-18) and playback the number five track.
4. Press the
^ (CD) button. (Becomes the 1 track jump mode)
5. Confirm that the level B and A (DC voltage) on the oscillo-
scope waveform.
1 track jump waveform
Specified level:
×
100 = less than ± 22%
6. After check, remove the lead wire connected in step 1.
Checking Location:
– BD BOARD (Side B) –
A
B
+
–
–
BD board
TP (TE)
TP (VC)
TP (VC)
oscilloscope
A (DC voltage)
center of
waveform
waveform
B
0V
level = 1.3
±
0.6 Vp-p
symmetry
TP (AGCCON)
TP (RF)
TP (GND)
TP (FE)
IC103
IC102
IC101
TP (FE1)
TP (VC)
TP (TE)
VIDEO SECTION
Frequency Adjustment
Connection:
Procedure:
1. Connect the frequency counter to TP508 (27 MHz) on VIDEO
1. Connect the frequency counter to TP508 (27 MHz) on VIDEO
board.
2. Turned power switch on.
3. Press the
3. Press the
[FUNCTION]
button to select the CD.
4. Adjust CT503 on the VIDEO board so that the frequency
counter reading 27.0 MHz ± 80 Hz at stop status.
Adjustment Location:
– VIDEO Board (Side A) –
+
–
–
TP508 (27 MHz)
VIDEO board
frequency counter
IC505
IC507
TP508
(27 MHz)
CT503
VIDEO
Frequency
Adjustment
HCD-VX5A/VX5AJ/VX7A
– 21 –
– 22 –
SECTION 7
DIAGRAMS
7-1.
BLOCK DIAGRAM – CD SERVO Section –
CD MECHANISM CONTROLLER
IC502 (1/2)
A/D
CONVERTER
CH1OUTF
CH1OUTR
5
4
7
2
1
5
10
6
6
7
8
16
14
13
10
11
22
4
3
24
25
23
5
6
2
3
17
18
15
16
A
E
B
C
D
A
CD A+5V
CD A+5V
F
DETECTOR
A
B
C
D
RF
SUMMING
AMP
FOCUS
ERROR AMP
RF EQ
AMP
TRACKING
ERROR AMP
RFO
FE
RF AMP,
FOCUS/TRACKING ERROR AMP
IC103
TE
E
F
F I-V AMP
E I-V AMP
AUTOMATIC
POWER CONTROL
Q101
OPTICAL
TRANSCEIVER
IC381
CD DIGITAL OUT
OPTICAL
APC LD
AMP
APC PD
AMP
LD
LD
PD
LASER DIODE
RFAC
ASYO
ASYI
CTL2
FILTER
FILO
PCO
CLTV
FILI
DIGITAL PLL
ASYMMETRY
CORRECTOR
EFM
DEMODULATOR
DIGITAL SIGNAL PROCESSOR
IC101 (1/2)
MDP
DIGITAL
CLV
PROCESSOR
32K
RAM
ERROR
CORRECTOR
INTERNAL BUS
SQCK
SQSO
MUTE
EXCK
PCMD
DATA
BCK
LRCK
C2PO
C4M
XTSL
XTAO
XTAI
BCK
LRCK
WDCK
C2PO
CTL1
CTL2
MD2
DOUT
DIGITAL
OUT
D/A
DIGITAL
INTERFACE
CLOCK
GENERATOR
SUBCODE
PROCESSOR
SCOR
WFCK
XUGF
GFS
EMPH
SENSE
DATA
CLOK
XLAT
SBSO
SENSE CLK
SENSE
DSP CLK
DSP DATA
DSP LATCH
SE
TE
FE
RFDC
FOCUS/
TRACKING/SLED
SERVO DSP
FOCUS/TRACKING/SLED
PWM GENERATOR
SFDR
CH3FIN
CH4SIN
CH3RIN
CH3OUTF
CH3OUTR
CH2FIN
CH2RIN
CH1FIN
CH1RIN
20
MUTE
SRDR
TFDR
TRDR
FFDR
FRDR
SSTP
COUT
S101
(LIMIT)
CD A+5V
MIRR,
DFCT, FOK
DETECTOR
SERVO AUTO
SEQUENCER
SERVO
INTERFACE
CPU INTERFACE
SCLK
TO CPU INTERFACE
FOK
MIRR
DFCT
CH4OUTF
CH4OUTR
M101
(SPINDLE)
MOTOR
DRIVE
XRST
LDON
DSP MUTE
MOTOR
DRIVE
COIL
DRIVE
CH2OUTF
CH2OUTR
COIL
DRIVE
M
M
M102
(SLED)
05
FOCUS/TRACKING COIL DRIVE,
SPINDLE/SLED MOTOR DRIVE
IC102
2-AXIS
DEVICE
(TRACKING)
(FOCUS)
DIGITAL SERVO
PROCESSOR
IC101 (2/2)
OPTICAL PICK-UP
(KSS-213D/Q-NP)
LDON
21
HOLD SW
PD
(Page 23)
•
SIGNAL PATH
: CD PLAY
: DIGITAL OUT
I-V AMP
12
11
13
14
CTRL1
CTRL2
CTL1
CTL2
SUBQ DATA
SUBQ CLK
SCOR
MCLK
33.8MHz
B
(Page 23)
DATA, BCK,
LRCK, C2PO
C
(Page 24)
IC104
TBL-L
TBL-R
M
DISC TRAY TURN MOTOR DRIVE
IC701
OUT1
OUT2
IN1
IN2
M701
(DISC TRAY TURN)
SYSTEM CONTROLLER
IC501 (1/4)
LEVEL SHIFT
Q701
DISC IN DETECT
SENSOR
IC703
DISC TRAY
SENSOR
IC702
ROTARY
ENCODER
S811
DISC-SENS
OUT-OPEN
S801
(OPEN/CLOSE DET)
ENC1
ENC2
ENC3
TBL-SENS
CLOSE
OPEN
LOAD-OUT
LOAD-IN
M
MOTOR
DRIVE
MOTOR
DRIVE
DISC TRAY SLIDE MOTOR DRIVE
IC801
OUT1
OUT2
FIN
RIN
M801
(DISC TRAY SLIDE)
RESET
DEVICE RESET
XRESET
33
31
32
29
30
34
19
8
40 41 39 43
22
20
21
26
TO SERVO AUTO
SEQUENCER
50
53 55
XPCK
12
52 54
49
48
25
76 77
66
71
16
69
72
67
65
17
64
63
2
14
79 80
15
7
4 6 5
10 11 13 68
3
XRST
3 5 4
1
18
36 37
10
28
2
12
77
27
11
60
61
71
70 69 68
59
4 2 3
65 63
67
10
2
3
6
7
4
7
2
66
DISC TRAY
ADDRESS DETECT
Click on the first or last page to see other HCD-VX5AJ / MHC-VX5 / MHC-VX5J / MHC-VX7 service manuals if exist.