Sony HCD-SX7 / HCD-SX7B Service Manual ▷ View online
HCD-SX7/SX7B
17
2-7. PANEL (FRONT) BLOCK-1
•
Continued on 2-8 (page 18).
–
Rear view
–
terminal side
1 two filament tapes
(sub
material)
6 filament tape
(sub
material)
filament tape
(sub material)
(sub material)
filament tape
(sub material)
(sub material)
filament tape
(sub material)
(sub material)
7 sleeve ferrite clamp
(FC1)
sleeve ferrite clamp
(FC1)
(FC1)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
How to install the connector
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
3 flexible flat cable (11 pin)
(CN011)
2 USB-HP board CN1501
cable
connector
(CN601)
4 USB-HP board CN1501
cable
connector
(CN605)
5 USB-HP board CN1501
cable
connector
(CN1101)
:LUHVHWWLQJ
MAIN board
Front
side
HCD-SX7/SX7B
18
2-8. PANEL (FRONT) BLOCK-2
6 panel (front) block
rib
rib
rib
USB-HP board
hook
4 Remove the panel (front) block
in the direction of the arrow.
2 three ornament
screws
–
Rear view
–
–
Panel (front) block rear view
–
:LUHVHWWLQJ
1 screw
(BV3
u 6)
3 claw
3 claw
3 claw
1 screw
(BV3
u 6)
3 claw
5 Draw the USB-HP board
CN1501 3 pin cable out
of the hole in chassis (sub).
5 Draw the USB-HP board CN1501
4 pin two cables and flexible flat
cable out of the hole in chassis (sub).
105 ± 5 mm
65 ± 5 mm
to USB-HP board
(CN1501)
binding band (taiton)
HCD-SX7/SX7B
19
2-9. LCD MODULE BLOCK
3 filament tape
(sub
material)
7 two claws
9 LCD module block
6 screw
(BV3
u 6)
6 screw
(BV3
u 6)
)OH[LEOHIODWFDEOHVHWWLQJ
filament tape
(sub material)
(sub material)
MAIN board
1 flexible flat cable
(6 pin) (CN007)
4 flexible flat cable
(6 pin) (CN006)
2 LCD flexible board
(CN002)
5 ferrite core (FC2)
ferrite core (FC2)
colored line
Insert straight into the interior.
flexible flat
cable
cable
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
+RZWRLQVWDOOWKHIOH[LEOHIODWFDEOH
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Insert straight into the interior.
LCD flexible
board
board
connector
OK
Insert at a slant.
LCD flexible
board
board
connector
NG
+RZWRLQVWDOOWKH/&'IOH[LEOHERDUG
When installing the LCD flexible board, ensure that it is
insert straight into the interior to the connector after insertion.
When installing the LCD flexible board, ensure that it is
insert straight into the interior to the connector after insertion.
terminal side
terminal side
terminal side
8 Draw the flexible flat cable (6 pin)
out of the hole in chassis (sub).
HCD-SX7/SX7B
20
2-11. LCD MODULE (LCD1)
2 two screws
(BTP
2.6
u 6)
1 Draw out the LCD module
flexible printed cable from the
hole.
hole.
3 Remove the LCD module block
in the direction of the arrow.
5 filament tape
(sub
material)
6 LCD module
(LCD1)
4 filament tape
(sub
material)
filament tape
(sub material)
(sub material)
guide line
holder (LCD)
filament tape
(sub material)
(sub material)
guide line
/&'PRGXOHIOH[LEOHSULQWHGFDEOHVHWWLQJ
Top side
Bottom side
2-10. NFC MODULE (NFC1)
1 Insert the stick into the hole of
the holder (LCD), and lift the
NFC module, then peel off
the adhesive sheet (NFC) with
a
NFC module, then peel off
the adhesive sheet (NFC) with
a
finger.
4 NFC module
(NFC1)
3 flexible flat cable
(6 pin) (FFC4)
2 Draw out the flexible flat
cable (6 pin) (FFC4)
from the hole.
from the hole.
colored line
Insert straight into the interior.
flexible flat
cable
cable
terminal side
connector
OK
colored line
Insert at a slant.
flexible flat
cable
cable
connector
NG
How to install the flexible flat cable
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
When installing the flexible flat cable, ensure that
the colored line is parallel to the connector after insertion.
Front side
hole
Click on the first or last page to see other HCD-SX7 / HCD-SX7B service manuals if exist.