Sony HCD-SX7 / HCD-SX7B Service Manual ▷ View online
HCD-SX7/SX7B
13
2-3. CARD WLAN/BT COMBO
Note 1: Be sure to replace the complete NETWORK board and card WLAN/
BT combo at the same time. Be sure to also follow “NOTE OF RE-
PLACING THE COMPLETE NETWORK BOARD AND CARD
WLAN/BT COMBO” on page 5 during replacement.
PLACING THE COMPLETE NETWORK BOARD AND CARD
WLAN/BT COMBO” on page 5 during replacement.
$QWHQQDZLUHVHWWLQJ
4 screw
(BV3
u 6)
5 card WLAN/BT combo
card WLAN/BT combo
2 wireless LAN
antenna
connector
(CON4)
3 MAIN board CN606
cable
connector
1 filament tape
(sub
material)
filament tape
(sub material)
(sub material)
cushion (B)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Note 2: Check that the wire
is not slack.
Note 3: Do not connect the
wire to the CON5.
HCD-SX7/SX7B
14
2-4. ANTENNA (2.4 GHz & 5 GHz) (ANT1), HOLDER (ANTENNA)
Note: When replacing the antenna (Ref. No. ANT1), refer to “CHECK-
ING OF NETWORK CONNECTION” on page 5.
5 Remove the cover (ANT) block
in the direction of the arrow.
6 cover (ANT) block
1 filament tape
(sub
material)
3 Move the antenna cable to the rear side.
2 wireless LAN
antenna
connector
(CON4)
4 two screws
(BTP2.6
u 6)
$QWHQQDZLUHVHWWLQJ
card WLAN/BT combo
filament tape
(sub material)
(sub material)
cushion (B)
Note 1: Check that the wire
is not slack.
Note 2: Do not connect the
wire to the CON5.
9 antenna (2.4 GHz & 5 GHz)
(ANT1)
0 screw
(BV/ring)
(L= 8 mm)
7 claw
qd holder
(antenna)
qs Rotate the claw of holder
(antenna) in the direction of
the arrow, align the hole of
panel
(back).
claw
qa boss
8 Draw the antenna wire
out of the hole.
HCD-SX7/SX7B
15
2-5. PANEL (CD) BLOCK
1 Insert the clip etc. in the hole
of the chassis, and push the
lever in the direction of the
arrow.
lever in the direction of the
arrow.
3 two claws
4 panel (CD) block
2 Draw out the tray.
tray
Insert the clip etc. processed to the
length of 8 cm or more in the hole
on the side of the chassis and push.
length of 8 cm or more in the hole
on the side of the chassis and push.
8 cm or more
–
Top view
–
–
Side view
–
hole
HCD-SX7/SX7B
16
2-6. PLATE (TOP) BLOCK
5 screw (BV/ring)
(L=8
mm)
5 screw
(BV/ring)
(L=8 mm)
(L=8 mm)
5 two screws (BV/ring)
(L=8
mm)
5 two screws (BV/ring)
(L=8
mm)
8 plate (top) block
6 Remove the plate (top)
block in the direction of
the
the
arrow.
$QWHQQDZLUHVHWWLQJ
card WLAN/BT combo
2 wireless LAN antenna
connector
(CON4)
3 MAIN board CN606
cable
connector
1 filament tape
(sub
material)
filament tape
(sub material)
(sub material)
cushion (B)
Insert only part way.
Insert straight into
the interior.
the interior.
connector
Insert at a slant.
connector
connector
connector
connector
connector
OK
NG
NG
+RZWRLQVWDOOWKHFRQQHFWRU
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Insert the connector straight into the interior.
There is a possibility that using this unit without
the connector correctly installed will damage it.
Note 1: Check that the wire
is not slack.
Note 2: Do not connect the
wire to the CON5.
4 Move the antenna cable
to the rear side.
7 Draw the MAIN board
CN606 cable out from
the hole of the plate
(top).
Click on the first or last page to see other HCD-SX7 / HCD-SX7B service manuals if exist.