DOWNLOAD Sony HCD-SHAKEX3 / HCD-SHAKEX7 Service Manual ↓ Size: 9.05 MB | Pages: 96 in PDF or view online for FREE

[PANEL TEST MODE]
This mode is used to check the fl uorescent indicator tube, LEDs, 
keys, [VOLUME/MULTI CONTROL] knob, model, destination 
and software version.
Procedure:
1. Press [] button and [S3 TUNING ‒ .] button simultane-

ously and hold 3 seconds.

2.  All LEDs and segments in fl uorescent indicator tube are 

lighted up. All RGB LEDs are lighted up in white color.

3.  When you want to enter to the software version display mode, 

press [S2 +] button.

 

The model information appears on the fl uorescent  indicator 
tube.

 Press 

[S2 

+] button again to view the destination information.

4.  During the destination information display, press [S2 +] 

button. Each time [S2 +] button is pressed, the fl uorescent 
indicator tube shows the version of each category software 
in the following sequence: SC, MTK, OPU, UI, PF, SUB, 
SYS, CD, CMA, CMB, ST, TA, TM and return back to model 
information display.

5. When [] button is pressed while the version numbers 

are being displayed except model and destination, the 
date of the software creation appears. When [] button is 
pressed again, the display returns to the software version 
display.

6. Press 

[S1 

‒] button, the key check mode is activated.

7.  In the key check mode, the fl uorescent indicator tube displays 

“K 0    V0”.

 

Each time a button is pressed, “K” value increases. However, 
once a button has been pressed, it is no longer taken into 
account.

 

“V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME/
MULTI CONTROL] knob is turned clockwise, or it decreases 
in the manner of 0, 9, 8, 7 ... if [VOLUME/MULTI CONTROL] 
knob is turned counterclockwise.

8.  When [ENTER] button is pressed after all LEDs and segments 

in  fl uorescent indicator tube light up, alternate segments in 
fl uorescent indicator tube and LEDs would light up, all RGB 
LEDs would light up in RED color. If you press [ENTER] 
button again, another half of alternate segments in fl uorescent 
indicator tube and LEDs would light up, all RGB LEDs would 
light up in GREEN color. Pressing [ENTER] button again 
would cause all segments in fl uorescent indicator tube and 
LEDs light up, all RGB LEDs would light up in blue color. 
Pressing [ENTER] button again would turn off all segments in 
fl uorescent indicator tube and all LEDs including RGB LEDs.

9.  To release from this mode, press the buttons in the same 

manner as step 1, or disconnect the power cord.

[USER RESET]
The user reset clears all data including preset data stored in the data 
fl ash to initial conditions exclude history mode data.
Procedure:
1. Press 

\/1

 button to turn on the system.

2.  Press [DJ OFF] button and [S4 TUNING + >] button simul-

taneously for 3 seconds.

3.  “RESET” appears on the fl uorescent indicator tube. After that, 

the fl uorescent indicator tube becomes blank for a while, and 
the system is reset.

[COLD RESET]
The cold reset clears all data including preset data stored in the 
data fl ash to initial conditions included history mode data. Execute 
this mode when returning the set to the customer.
Procedure:
1. Press 

[

\/1

] button to turn on the system.

2. Press [] button and [S4 TUNING + >] button simultane-

ously for 3 seconds.

3.  “COLD RESET” appears on the fl uorescent indicator tube. 

After that, the fl uorescent indicator tube will display “SONY 
DEMO”. The set will automatically Power ON and Power 
OFF again, and the system is reset.

[DISC TRAY LOCK MODE]
This mode let you lock the disc tray. When this mode is activated, 
the disc tray will not open when [Z] button is pressed. The message 
“LOCKED” will be displayed on the fl uorescent indicator tube. 
This mode only applied when there is disc on the tray.
Procedure:
1. Press 

[

\/1

] button to turn on the system.

2.  Select DVD/CD function.
3.  Press [DJ OFF] button and [ISOLATOR] button simultaneously 

and hold down until “LOCKED” or “UNLOCKED” displayed 
on the fl uorescent indicator tube (around 5 seconds).

[Bluetooth PAIRING HISTORY CLEAR]
It can clear the Bluetooth pairing history.
Procedure:
1. Press 

the 

[

\/1

] button to turn the power on.

2.  Press the [BLUETOOTH] button to turn the Bluetooth func-

tion.

3.  Press [DJ OFF] button and [‒] button simultaneously for 3 

seconds.

4.  The message “BT HISTORY” → “CLEAR” is displayed 

on the fluorescent indicator tube, and the pairing history of 
Bluetooth is cleared.

P

C

O

U

N

T

※

※

No of time protector happen (0 ~ 99)

P

T

※

※

※

※

Refer to protect type description

1

*h

*h

*h

*h

*h.

*m

*m

Single Power On Time until protector happened
(0~99999 hours, 0~99Min)

2

*h

*h

*h

*h

*h.

*m

*m

Total Power On Time [ no consider protector happen ]
(0~99999 hours, 0~99Min)

F

※

※

※

※

※

※

Input Function during protector happened

V

O

L

※

※

※

Volume setting (MIN / 1 - 50 / MAX)

B

A

S

S

※

※

※

MEGA BASS setting (OFF / ON)

[HISTORY MODE]
This mode is used to check important data stored in the system 
when PROTECTOR happen.
Procedure:
1.  During demo mode, press [] button and [S2 +] button for 

5 seconds to mode into history mode.

2.  Press the [S4 TUNING + >] button or [S3 TUNING ‒ .] 

button to check history data stored.

To release from History Mode.
To release from this mode, press [

\/1

] button.

01

The over current condition to MOSFET occurs 
by defect of MOSFET or defect of PS output 
line.
or
Unusual heat up of MOSFET by improper 
assembly of heat sink, destruction of MOSFET 
etc.

02

Defect of thermistor IC or charging circuit used 
by SPM (Sound Pressure Management) system.

03

Defect of power supply circuit to AMP. There 
is possibility of unusual power supply of any of 
the AMP IC or Pre-amplifi er.

04

DC appears in SP terminal by defect of AMP 
IC and MOSFET

06

Defect of DC FAN and DC FAN driver circuit

RESET defect

Reset signal status from micom is not ‘H’.

[DVD COLOR SYSTEM MODE]
•  This mode let you change the color system of the video output 

from PAL to NTSC or vice-versa.

Procedure:
1.  Press the [\/1] button to turn on the system.
2.  Press [FUNCTION +] or [FUNCTION ‒] at remote com-

mander to select DVD/CD function.

3. Press the [DJ OFF] button and [FOOTBALL] button 

simultaneously and hold for 3 seconds.

4.  The message “COLOR PAL” or “COLOR NTSC” appears on 

the fl uorescent indicator tube.

•  To release from DVD Color System Mode
1.  Once the color system has been selected, the mode is fi xed 

there after. If you wish to change the mode again, perform the 
above item 2 again.

[DVD SERVICE MODE]
•  This mode let you make diagnosis and adjustment easily by 

using the remote commander and the TV. The instructions, 
diagnostic results, etc. are given on the on-screen display.

•  TEST DISC LIST
 

Be sure to use the DVD disc that matches the signal standards 
of your region.

 

•  CD

YEDS-18 

(Part No.: 3-702-101-01)

 

 

PATD-012 

(Part No.: 4-225-203-01)

 

 

 

HLX-A1 

(Part No.: J-2501-307-A)

 

•  DVD SL (Single Layer)

NTSC :  HLX-503  (Part No.: J-6090-069-A)

 

  HLX-504  (Part No.: J-6090-088-A)

 

 

 

  HLX-513  (Part No.: J-2501-305-A)

PAL : HLX-506  (Part No.: J-6090-077-A)

 

•  DVD DL (Double Layer)

NTSC :  HLX-501  (Part No.: J-6090-071-A)

 

  HLX-505  (Part No.: J-6090-089-A)

 

 

 

  HLX-514  (Part No.: J-2501-306-A)

PAL : HLX-507  (Part No.: J-6090-078-A)

•  Procedure to enter to DVD Service Mode:
1.  Press the [\/1] button to turn on the system.
2.  Press [FUNCTION +] or [FUNCTION ‒] at remote com-

mander to select DVD/CD function.

3.  Press the [SPEAKER LIGHT] button and [ENTER] button 

simultaneously and hold 3 seconds.

4.  The message “SERVICE IN” appears on the fl uorescent 

indicator tube.

 

The display of the “Model Name” of the “Remocon Diagnosis 
Menu” change with the model and the destination appears on 
screen display. Refer to below on the model name.

 

SHAKE-X1D : TETSUJIN

 

SHAKE-X3D : RAIJIN

 

SHAKE-X7D : RYUJIN

 

*1: Changes depending on destination

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information

Model Name : SHAKE-X1D_ XX *1 or SHAKE-X3D_ XX 

*

1 or

: SHAKE-X7D_ XX 

*

1

IF-con
Syscon

: Ver.  XX.XX (XXXX)
: Ver.  X.XXX

5.  To execute each function, press its number by using numeric 

button on the remote commander.

6.  To release from this mode, press the [\/1] button to turn off 

the system.

•  Execute IOP Measurement
 

In order to execute IOP measurement, the following standard 
procedures must be followed.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“2. Drive Manual Operation” by pressing the [2] button on 
the remote commander. The following screen appears on the 
onscreen display.

2.  Select “3. Manual Adjustment” by pressing the [3] button on 

the remote commander. The following screen appears on the 
on-screen display.

3.  Select “6. Iop:” by pressing the [6] button on the remote 

commander.

4.  Wait until a hexadecimal number appears in the on-screen 

display as below:

5. Convert data from hexadecimal to decimal by using 

conversion table.

6. Please 

fi nd the label on the rear of the BU (Base Unit).

 

The default IOP value is written in the label.

7.  Subtract between these two values.

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time Adjust
0. Return to Top Menu

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type

•  Parameter of error code
 

This is the detail of error code.

•  Time of error code
 

This is the laser time when an error occurred.

To clear the Laser Hours
Press the [  DISPLAY] button and then press the [CLEAR] 
button. The data for both CD and DVD data are reset.

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

Emg. History Check

1.  01  05  04  04

Laser Hours

CD

0h

0min

DVD

0h

0min

00  92  46  00

00  00  00  00

00  00  23  45

2.  02  02  01  01

00  A9  4B  00

00  00  00  00

00  00  23  45

Next   Next Page

Prev  Prev Page

O  Return to Top Menu

8.  If the remainder is smaller than 93 (decimal), then it is OK.
 

However if the value is higher than 93, then the BU is defective 
and need to be change.

9.  Press the [RETURN] button on the remote commander to 

return to previous menu.

10.  Press the [0] button on the remote commander to return to the 

Top Menu of Remocon Diagnosis Menu.

11.  Press the [\/1] button to turn off the system.

•  Check Emergency History
 

To check the emergency history, please follow the following 
procedure.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“3. Emergency History” by pressing the [3] button on the 
remote commander. The following screen appears on the on-
screen display.

Emg. History Check

1.  01  05  04  04

Laser Hours

CD

999h

59min

DVD

999h

59min

00  92  46  00

00  00  00  00

00  00  23  45

2.  02  02  01  01

00  A9  4B  00

00  00  00  00

00  00  23  45

Next   Next Page

Prev   Prev Page

O  Return to Top Menu

 

(Displayed values in the above fi gure are example)

2.  You can check the total time when the laser is turned on 

during playback of DVD and CD from the above menu. The 
maximum time, which can be displayed are 999h 59min.

3.  You can check the error code of latest 10 emergency history 

from the above menu. To view the previous or next page of 
emergency history, press the [.] button or [>] button 
on the remote commander. The error code consists of “Error 
Code”, “Parameter of error code” and “Time of error code”.