DOWNLOAD Sony HCD-SHAKE100 / HCD-SHAKE99 Service Manual ↓ Size: 9.07 MB | Pages: 112 in PDF or view online for FREE

[MODEL & DEST WRITE MODE]
This mode is used to set software model & destination.
This mode only available when no permanent model & destination 
is stored.

1.  Press [MOVIE/GAME] button & [LED PATTERN] button 

simultaneously and hold for 5 seconds.

2.  Fluorescent indicator tube display will show “M XXXXX”.
3. Press 

[

+]

*1

 / [PRESET + +]

*2

 / [‒

]

*1

 / [‒ PRESET ‒]

*2

button to select the model based on the set’s model.

SHAKE-99/SHAKE-100D

“M MAGMA9/MAGMA9D”

4.  Press [ENTER] button.
5.  Fluorescent indicator tube display will show “D XXXXX”.
6.  Press  [

+]

*1

 / [PRESET + +]

*2

 / [‒

]

*1

 / [‒ PRESET ‒]

*2

button to select the destination based on the set’s country.

J1

Japan

“D J”

JE1

Tourist

“D JE”

U2/CA2

America, Canada

“D NA”

CEL/CE1/
CE2

Europe(general)

“D CE2”

CEK

U.K.

“D CEK”

RU1/RU3

Russia

“D RU”

AU1

Australia

“D AU”

CN1

China

“D CN”

E12

India, Pakistan, Morocco

“D E12”

E3/E15

Middle East, Africa 
(South Africa), Iran

“D E3”

E4/EA3/
E93/SA2

Saudi Arabia, Africa

“D EA3”

HK1/
HK2/PL1/
SP1/SP2/
SP6/TH1

Hong Kong, Philippines, 
Singapore, Malaysia, 
Thailand

“D ASIA”

KR2

Korea

“D KR”

TW2

Taiwan

“D TW”

E2, E32, 
E51, AR2

Latin America(general), 
Chile, Peru, Argentina

“D LATIN”

BR1

Brazil

“D BR”

MX2, 
MX4

Mexico

“D MX”

7.  Press [ENTER] button to confi rm the selection.
8.  “RESET” appears on the fl uorescent indicator tube. After that, 

the fl uorescent indicator tube becomes blank for a while, and 
the system is reset.

9.  Mode in [PANEL TEST MODE] again to confi rm on the 

model & destination.

*1

 SHAKE99 model

*2

 HCDSHAKE100 model

[DVD COLOR SYSTEM MODE]
• 

This mode let you change the color system of the video output 
from PAL to NTSC or vice-versa.

1.  Press the [\/1] button to turn on the system.
2.  Press the [DVD/CD] button.
3.  Press the [DVD/CD] button and [PAN] button simultaneously 

and hold for 3 seconds.

4.  The message “COLOR PAL” or “COLOR NTSC” appears on 

the fl uorescent indicator tube.

1.  Once the color system has been selected, the mode is fi xed 

there after. If you wish to change the mode again, perform the 
above item 2 again.

[DVD SERVICE MODE]
•  This mode let you make diagnosis and adjustment easily by 

using the remote commander and the TV. The instructions, 
diagnostic results, etc. are given on the on-screen display.

 

Be sure to use the DVD disc that matches the signal standards 
of your region.

 

•  CD

YEDS-18 

(Part No.: 3-702-101-01)

 

 

PATD-012 

(Part No.: 4-225-203-01)

 

•  DVD SL (Single Layer)

NTSC :  HLX-503  (Part No.: J-6090-069-A)

 

  HLX-504  (Part No.: J-6090-088-A)

PAL : 

HLX-506  (Part No.: J-6090-077-A)

 

•  DVD DL (Double Layer)

NTSC :  HLX-501  (Part No.: J-6090-071-A)

 

  HLX-505  (Part No.: J-6090-089-A)

PAL : 

HLX-507  (Part No.: J-6090-078-A)

1.  Press the [\/1] button to turn on the system.
2.  Press the [DVD/CD] button.
3.  Press the [DVD/CD] button and [WAH] button simultaneously 

and hold 3 seconds.

4.  The message “SERVICE IN” appears on the fl uorescent 

indicator tube.

 

The display of the “Model Name” of the “Remocon Diagnosis 
Menu” change with the model and the destination appears on 
screen display. Refer to below on the model name.

 SHAKE-100D: 

MAGMA9D

 

*1: Changes depending on destination

5.  To execute each function, press its number by using numeric 

button on the remote commander.

6.  To release from this mode, press the [\/1] button to turn off 

the system.

Remocon Diagnosis Menu

0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5.  USB Test Mode Setting

Model Name
IF-con
Syscon

: GSX8D_ XX 

*1

: Ver.  XX.XX (XXXX)
: Ver.  X.XXX

 

To check the emergency history, please follow the following 
procedure.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“3. Emergency History” by pressing the [3] button on the 
remote commander. The following screen appears on the on-
screen display.

2.  You can check the total time when the laser is turned on 

during playback of DVD and CD from the above menu. The 
maximum time, which can be displayed are 999h 59min.

3.  You can check the error code of latest 10 emergency history 

from the above menu. To view the previous or next page of 
emergency history, press the [.] button or [>] button 
on the remote commander. The error code consists of

The meaning of error code is as below:
01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mechanical move error (5 Changer)
26: Mechanical move stack error
30: DC motor adjustment error
31: DPD offset adjustment error
32: TE balance adjustment error
33: TE sensor adjustment error
34: TE loop gain adjustment error
35: FE loop gain adjustment error
36: Bad jitter after adjustment
40: Focus NG
42: Focus layer jump NG
51: Spindle stop error
52: Open kick spindle error
60: Focus on error
61: Seek fail error
62: Read Q data/ID error
70: Lead in data read fail
71: TOC read time out (CD)
80: Can’t buffering
81: Unknown media type

Emg. History Check

1.  01  05  04  04

Laser Hours

CD

999h

59min

DVD

999h

59min

00  92  46  00

00  00  00  00

00  00  23  45

2.  02  02  01  01

00  A9  4B  00

00  00  00  00

00  00  23  45

Next   Next Page

Prev   Prev Page

O  Return to Top Menu

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

 

In order to execute IOP measurement, the following standard 
procedures must be followed.

1.  From the Top Menu of Remocon Diagnosis Menu, select 

“2. Drive Manual Operation” by pressing the [2] button on 
the remote commander. The following screen appears on the 
onscreen display.

2.  Select “3. Manual Adjustment” by pressing the [3] button on 

the remote commander. The following screen appears on the 
on-screen display.

3.  Select “6. Iop:” by pressing the [6] button on the remote 

commander.

4.  Wait until a hexadecimal number appears in the on-screen 

display as below:

5. Convert data from hexadecimal to decimal by using 

conversion table.

6. Please 

fi nd the label on the rear of the BU (Base Unit).

 

The default IOP value is written in the label.

7.  Subtract between these two values.
8.  If the remainder is smaller than 93 (decimal), then it is OK.
 

However if the value is higher than 93, then the BU is defective 
and need to be change.

9.  Press the [RETURN] button on the remote commander to 

return to previous menu.

10.  Press the [0] button on the remote commander to return to the 

Top Menu of Remocon Diagnosis Menu.

11.  Press the [\/1] button to turn off the system.

 

Drive Manual Operation

1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu

 

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:

O

 

o Change Value

RETURN  Return to previous menu

 

This is the detail of error code.

 

This is the laser time when an error occurred.

Press the [

 DISPLAY] button and then press the [CLEAR] 

button. The data for both CD and DVD data are reset.

Press the [DVD TOP MENU] button and then press the [CLEAR] 
button.
The error code for all emergency history would be reset.

Press the [DVD/TUNER MENU] button and then press the 
[CLEAR] button on the remote commander.

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

Example of Error code

1.  01  05  04  04

00  92  46  00

00  00  00  00

00  00  23  45

Emg. History Check

1.  01  05  04  04

Laser Hours

CD

0h

0min

DVD

0h

0min

00  92  46  00

00  00  00  00

00  00  23  45

2.  02  02  01  01

00  A9  4B  00

00  00  00  00

00  00  23  45

Next   Next Page

Prev  Prev Page

O  Return to Top Menu

Emg. History Check

1.  00  00  00  00

Laser Hours

CD

999h

59min

DVD

999h

59min

00  00  00  00

00  00  00  00

00  00  00  00

2.  00  00  00  00

00  00  00  00

00  00  00  00

00  00  00  00

Next   Next Page

Prev   Prev Page

O  Return to Top Menu

Emg. History Check

Initialize setup data...

Laser Hours

CD

999h

59min

DVD

999h

59min

Next   Next Page

Prev   Prev Page

O  Return to Top Menu

Press the [0] button on the remote commander.

 

To check the version information, please follow the following 
procedure.

1.  From the Top Menu of Remocon Diagnosis Menu, select “4. 

Version information” by pressing the [4] button on the remote 
commander. The following screen appears on the on-screen 
display.

To return to the Top Menu of Remocon Diagnosis Menu, press 
the [0] button on the remote commander.

Version information

O  Return to Top Menu

Firm (Main) :  Ver. xxxxx
Firm (Sub) :  xxxxx
RISC :   xxxxx
8032 :   xxxxx
Audio DSP :  xxxxx
Servo DSP :  xxxxx

Procedure:
1.  Connect the oscilloscope to CN302 pin 17 (RFMON) and 

CN302 pin 1 (GND) on the MOTHERBOARD board.

2. Press 

the 

[

?/1

] button to turn the power on, and press the [CD]

(SHAKE99)/[DVD/CD](HCDSHAKE100) button to select 
CD/DVD function.

3.  Set the test disc (CD: YEDS-18), (DVD: HLX-503 (NTSC) 

or HLX-504 (PAL) on the tray and press [u] button to 
playback.

4. Confi rm that oscilloscope waveform is as shown in the fi gure 

below (eye pattern).

 

A good eye pattern means that the diamond shape (

) in the 

center of the waveform can be clearly distinguished.

1.  Turn the power on.
2.  Input the following signal from Signal Generator to FM
 

antenna input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation 

: 75 kHz

Modulation 

: 1 kHz

ANT input 

: 35 dBu (EMF)

Note:  Please use 75 ohm “coaxial cable” to connect SG and the 
 

  set. You cannot use video cable for checking. 

 

  Please use SG whose output impedance is 75 ohm.

3.  Set to FM tuner function and scan the input FM signal with
 automatic 

scanning.

4. Confi rm that input Frequency of A, B and C detected and
 

automatic scanning stops.

The stop of automatic scanning means “The station signal is
received in good condition”.

0 dB = 1 

ȝV

[TEST DISC LIST]
Use the following test disc on test mode.
• CD: 

YEDS-18 (PART No. 3-702-101-01)

   

or

     

PATD-012 (PART No. 4-225-203-01)

• DVD (SL)
  NTSC 

HLX-503 (PART No. J-6090-069-A)

   

or

     

HLX-504 (PART No. J-6090-088-A)

  PAL 

HLX-506 (PART No. J-6090-077-A)

• DVD (DL)
  NTSC 

HLX-501 (PART No. J-6090-071-A)

   

or

     

HLX-505 (PART No. J-6090-089-A)

  PAL 

HLX-507 (PART No. J-6090-078-A)

Note:  When the BASE UNIT is replaced, perform the Execute 

IOP measurement 

 

(Refer to page 18).

CN302

pin 1 (GND)

pin 17 (RFMON)