Sony HCD-SB500W Service Manual ▷ View online
5
HCD-SB500W
SECTION 1
SERVICING NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
RELEASING THE DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
disc in the store is equipped.
Releasing Procedure :
Press two buttons of
Press two buttons of
A
and
x
simultaneously for five seconds.
The message “UNLOCKED” is displayed and the tray is unlocked.
Note:
When “LOCKED” is displayed, the tray lock is not released by turning
power on/off with the
power on/off with the
I/
1
button.
NOTE OF REPLACING THE DMB07 BOARD
When replacing the DMB07 board, since the adjustment value is
not set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
not set up correctly, “Drive Auto Adjustment” can’t be performed.
In this case, initialize Memory in the following procedures.
Procedure:
1. Set the test mode. (See page 15)
2. Press the [2] key of the remote commander, and set the “DRIVE
2. Press the [2] key of the remote commander, and set the “DRIVE
MANUAL OPERATION”. (See page 18)
3. Press the [6] key of the remote commander, and set the “2-6,
Memory Check”. (See page 20)
4. Press the [CLEAR] key of the remote commander, and initialize
Memory.
•
MODEL IDENTIFICATION
MODEL
PART No.
AEP, UK models
2-067-992-0[]
Korean model
2-067-992-1[]
Singapore model
2-067-992-2[]
Hong Kong model
2-067-992-3[]
Australian model
2-067-992-4[]
Russian model
2-067-992-5[]
PART No.
– Back Panel –
6
HCD-SB500W
DECISION TO PASS OR FAIL OF THE OPTICAL
PICK-UP BLOCK
PICK-UP BLOCK
Connection:
Procedure:
1. Connect an oscilloscope to test point 1 pin and 3 pin of
CN901 on the DMB07 board.
2. Turn the power on.
3. Put the disc (LUV-P01) (Part No.: 4-999-032-01) (CD) in to
3. Put the disc (LUV-P01) (Part No.: 4-999-032-01) (CD) in to
playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
5. Put the disc (TDV-520CSO) (Part No.: J-2501-236-A) (DVD)
is to playback.
6. Perform confirmation in the same manner as step 4.
Note:
A clear RF signal waveform means that the shape “
◊” can be clearly
distinguished at the center of the waveform.
Checking Location:
DMB07 board
CN901
1
pin
CN901
3
pin
+
–
–
oscilloscope
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
TIME/DIV: 500 ns
CD: 1.05
±
0.2 Vp-p
DVD: 1.09
±
0.2 Vp-p
RF signal waveform
– DMB07 Board (Component Side) –
CN901
IC701
IC207
IC801
1
7
7
HCD-SB500W
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Front Panel
A "
/
1
(power)
B
Disc tray
C A
(open/close)
D H
(play)
E X
(pause)
F x
(stop)
G .
/
>
, PRESET –/+
H
FUNCTION
I
VOLUME –/+
J
PHONES jack
K
Front panel display
L
STANDBY indicator
M
(remote sensor)
STANDBY
PHONES
VOLUME
PRESET
FUNCTION
Rear Panel
1
SPEAKER jacks
2
DIR-T1 jack
3
VIDEO AUDIO IN L/R jacks
4
COMPONENT VIDEO OUT jacks
6
MONITOR OUT (VIDEO/S VIDEO) jacks
7
AM terminals
8
FM 75 COAXIAL jack
9
SAT AUDIO IN L/R jacks
FRONT L
WOOFER
CENTER
SPEAKER
FRONT R
WOOFER
AUDIO IN
L
R
AUDIO IN
L
R
VIDEO
SAT
COAXIAL
AM
FM
75
DIR-T1
Y
P
B
/C
B
P
R
/C
R
COMPONENT VIDEO OUT
MONITOR OUT
S VIDEO (DVD ONLY)
VIDEO
5
EURO AV OUTPUT (TO TV) jack
OUTPUT(TO TV)
EURO AV
(except AEP, UK models)
(AEP, UK models only)
(except AEP, UK models)
1
2
3
4
6
7 8
9
5
8
HCD-SB500W
Remote
A
SONY TV DIRECT
B
SLEEP
C
TUNER/BAND
D
MUTING
E
TUNER MENU
F
PLAY MODE
G
REPEAT
H
FM MODE
I
TV
J
AUDIO
K
ANGLE
L
SUBTITLE
M .
/
>
, PRESET –/+
N H
PLAY
O X
PAUSE
P
DVD TOP MENU/ALBUM–
Q C
/
X
/
x
/
c
/ENTER
R
DVD DISPLAY
S
TV CH +/–
T
TV VOL +/–
U
TV
[
/
1
(on/standby)
V "
/
1
(standby)
W Z
(open/close)
X
DSGX
Y
AUTO FORMAT DIRECT
Z
MODE
wj
NIGHT MODE
wk
FUNCTION
wl
Number buttons
e;
ENTER
ez
m
/
M
/
/
SLOW, TUNING –/+
es
x
STOP
ed
DISPLAY
ef
DVD MENU/ALBUM+
eg
VOLUME +/–
eh
O
RETURN
ej
TV/VIDEO
ek
CLEAR
el
DIMMER
r;
DVD SETUP
1
2
3
4
5
8
0
6
7
10
9
Click on the first or last page to see other HCD-SB500W service manuals if exist.