Sony HCD-S500HDE / NAS-SC500PK / SS-S500HDE Service Manual ▷ View online
HCD-S500HDE/SS-S500HDE
5
HOW TO DRAW OUT FORCIBLY THE DISC TRAY
In the event that the disc tray does not come out due to any fail-
ure, three methods are available to draw it out forcibly. Use either
method described below according to the symptom.
In the event that the disc tray does not come out due to any fail-
ure, three methods are available to draw it out forcibly. Use either
method described below according to the symptom.
METHOD 1
If the power did not turn on or if the power is OFF:
1. With the power cord unplugged, remove the panel (side L) /
If the power did not turn on or if the power is OFF:
1. With the power cord unplugged, remove the panel (side L) /
(side R) assembly, panel (top), and panel (front). (See “How to
Remove 2-2, 2-3 (page 8), 2-6 (page 10)”)
Remove 2-2, 2-3 (page 8), 2-6 (page 10)”)
2. As shown in the fi gure, insert a thin rod into the hole at the
lower part of CD block, and push it in the arrow
A direction.
"
Note:
This illustration shows the
disc tray as viewed from
the
bottom.
CD section
thin rod
hole
cushion (CD)
Insert a thin rod into the
hole and push it in the
arrow " direction.
hole and push it in the
arrow " direction.
(Disc tray will come out)
disc tray
Peel the cushion (CD) a
little when it hides the hole.
little when it hides the hole.
METHOD 2
If the CD-ROM drive is turned on but the mother board does not
start:
1. Insert a thin fl at-head screwdriver into a round hole at the bot-
If the CD-ROM drive is turned on but the mother board does not
start:
1. Insert a thin fl at-head screwdriver into a round hole at the bot-
tom of the set.
2. Through a hole at the bottom of CD-ROM drive, short the
points (patterns) on the board of CD-ROM drive.
round hole
round hole
flat-head screwdriver
pattern
Short across patterns with a flat-head screwdriver.
disc tray
flat-head screwdriver
METHOD 3
If the mother board starts but the system software is abnormal:
Plug in the power cord while pressing the [
If the mother board starts but the system software is abnormal:
Plug in the power cord while pressing the [
Z] button.
Note: This method is same as “CD Start Mode” of test modes. Load the
start disc and close the disc tray, and if the start disc is not recog-
nized, start the CD as usual.
nized, start the CD as usual.
;button
power cord
HCD-S500HDE/SS-S500HDE
6
DISCHARGE PROCESSING
1. Switching power block on primary side of MAIN board
1. Switching power block on primary side of MAIN board
Though high voltage of 280 V is applied to the electrolytic
capacitor (C205), in about 3 seconds after the AC cord was
unplugged, the voltage will lower to 3 to 4 V.
capacitor (C205), in about 3 seconds after the AC cord was
unplugged, the voltage will lower to 3 to 4 V.
However, in the case of standalone MAIN board, the discharge
time will be long because of small load.
time will be long because of small load.
The voltage at this time is about 290 V.
The voltage becomes half in about 20 seconds after the AC
cord was unplugged. After that, in about 5 seconds, the voltage
will lower to about 3 V rapidly.
cord was unplugged. After that, in about 5 seconds, the voltage
will lower to about 3 V rapidly.
Then, the discharge slows and accordingly the forced dis-
charge processing is necessary.
• Forced discharge processing method
Connect a resistor such as 100 Ω/3 W to the terminals of
• Forced discharge processing method
Connect a resistor such as 100 Ω/3 W to the terminals of
C205 and execute the discharge processing. (Discharge for
about 10 seconds)
about 10 seconds)
Note: The potential of about 145 V exists across aluminum case of C205.
You could get an electric shock if you touch the aluminum case of
C205.
C205.
2. Power block on secondary side of MAIN board
In about 3 seconds after the AC cord was unplugged, almost all
potentials will lower to below 3 V, but after that the discharge
slows and accordingly the forced discharge processing is nec-
essary.
• Forced discharge processing method
Connect a resistor such as 100 Ω/3 W to the terminals of
potentials will lower to below 3 V, but after that the discharge
slows and accordingly the forced discharge processing is nec-
essary.
• Forced discharge processing method
Connect a resistor such as 100 Ω/3 W to the terminals of
C308 and C310, and execute the discharge processing. (Dis-
charge for about 5 seconds)
charge for about 5 seconds)
For electrolytic capacitors other than C205, 308 and 310, the
discharge processing is executed simultaneously with the
above discharge processing, and therefore the forced discharge
processing is not necessary.
discharge processing is executed simultaneously with the
above discharge processing, and therefore the forced discharge
processing is not necessary.
100
Ω/3 W
C310
C308
C205
100
Ω/3 W
100
Ω/3 W
– MAIN Board (Conductor Side) –
HCD-S500HDE/SS-S500HDE
7
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
2-1. DISASSEMBLY FLOW
SET
2-2. LID (WM)
PANEL (SIDE L/R) ASSY
(Page 8)
2-6. FRONT PANEL BLOCK
(Page 10)
2-10. SP/DMPORT BOARD,
MAIN BOARD
(Page 12)
2-12. FAN, (DC) (M101),
CHASSIS (MID)
(Page 13)
2-11. HARD DISK DRIVE
(Page 12)
2-13. CD BLOCK
(Page 13)
2-14. CD-ROM DRIVE (CD-5010A-020)
(Page 14)
2-7. KNOB (VOL-L) ASSY,
FRONT PANEL BOARD
(Page 10)
2-3. COVER (BASE) BLOCK,
PANEL (TOP) BLOCK
(Page 8)
2-4. TOP PANEL BOARD,
LCD BLOCK
(Page 9)
2-5. LCD MODULE
(Page 9)
2-9. MOTHER BOARD
(Page 11)
2-8. CHASSIS (TOP)
(Page 11)
HCD-S500HDE/SS-S500HDE
8
Note: Follow the disassembly procedure in the numerical order given.
2-2. LID (WM), PANEL (SIDE L/R) ASSY
Note: This illustration sees the set from back.
2-3. COVER (BASE) BLOCK, PANEL (TOP) BLOCK
#
"
Remove the panel (side L) assy
in the direction of ".
Remove the panel (side R) assy
in the direction of #.
two screws
(BVTT3
× 6)
two screws
(BVTT3
× 6)
two screws
(BVTT3
× 6)
two screws
(BVTT3
× 6)
lid (WM)
Push the “PUSH” in the
direction of arrow.
RM
cover (base) block
wire (flat type) (15 core)
(CN8)
two screws
(BV3
× 8)
RI two screws
(BV3
× 8)
screw
(BVTP3
× 8)
RI two screws
(BV3
× 8)
connector
(CN4002)
connector
(CN4004)
connector
(CN702)
RE connector (CN3002)
RG ferrite core
connector
(CN13)
RT earth terminal
RL two earth terminals
RH three screws
(BV3
× 8)
RB three screws
(BV3
× 8)
three claws
three claws
RK screw
(BV3
× 8)
X panel (top) block
earth terminal
Click on the first or last page to see other HCD-S500HDE / NAS-SC500PK / SS-S500HDE service manuals if exist.