Sony HCD-RX80 / MHC-RX80 Service Manual ▷ View online
– 33 –
TUNER SECTION
0 dB=1 µV
Note: As a front-end (FE1) is difficult to repair if faulty, replace it
with new one.
AM Section Adjustment
Setting:
AM Tuned Level Adjustment
Band: AM or MW
Procedure:
1. Set the output of SSG so that the input level of the set becomes
Procedure:
1. Set the output of SSG so that the input level of the set becomes
55 dB.
2. Tune the set to 999 kHz.
3. Adjust RV41 to the point (moment) when the TUNED indicator
3. Adjust RV41 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location : TCB board
FM Section Adjustment
Note: This adjustment should be performed after the AM Tuned
Level Adjustment due to the same adjustment element.
Setting:
AM RF SSG
loop antenna
set
loop antenna
(Supplied accessories)
60 cm
AM ANTENNA
terminal (TM1)
30% amplitude
modulation by
400 Hz signal
Field strength dB (
µ
V/m) =SSG output level dB (
µ
V/m) –26 dB.
FM Tuned Level Adjustment
Band: FM
Procedure:
1. Supply a 25 dBµ 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV42 to the point
Procedure:
1. Supply a 25 dBµ 98 MHz signal from the ANTENNA terminal.
2. Tune the set to 98 MHz.
3. If the TUNED indicator does not light, adjust RV42 to the point
(moment) when the TUNED indicator will change from going
off to going on.
off to going on.
Adjustment Location: TCB board
Adjustment Location:
[TCB BOARD] (Component Side)
RV42
IC41
RV41
TM1
FE1
Carrier frequency : 98 MHz
Modulation : AUDIO 1 kH, 75 kHz
deviation (100%)
Modulation : AUDIO 1 kH, 75 kHz
deviation (100%)
FM ANTENNA terminal
(TM1) (75
(TM1) (75
Ω
open)
75
Ω
coaxial
set
FM RF stereo signal
generator
generator
– 34 –
FM Polar Adjustment (EE, CIS model only)
Connection 1:
Procedure :
1. Set the modulation of FM RF SSG to AUDIO 1 kHz, 10 kHz
deviation according to "Connection 1".
2. Tune the set to 69 MHZ.
3. Adjust the RV1702 so that the reading of frequency counter
3. Adjust the RV1702 so that the reading of frequency counter
connected to TP1702 becomes within 31.25 kHz ± 0.05 kHz.
(VCO adjustment)
(VCO adjustment)
4. Then record the reading of the level meter connected to TP1701
5. Set the modulation of FM RF SSG to AUDIO 31.25 kHz, 10
5. Set the modulation of FM RF SSG to AUDIO 31.25 kHz, 10
kHz deviation according to "Connection 2".
6. Tune the set to 69 MHz.
7. Set the CT1701 to be mechanical center.
8. Adjust the L1701 so that the reading of the level meter con-
7. Set the CT1701 to be mechanical center.
8. Adjust the L1701 so that the reading of the level meter con-
nected to TP1701 become maximum.
Then adjust the CT1701 so that the reading of the level meter
connected to TP1701 becomes maximum. (SUB CARRIER
PEAK Adjustment)
Then adjust the CT1701 so that the reading of the level meter
connected to TP1701 becomes maximum. (SUB CARRIER
PEAK Adjustment)
9. Adjust the RV1701 so that the level at the moment becomes 14
dB higher value than the level recorded in step 4. (SUB CAR-
RIER LEVEL Adjustment)
RIER LEVEL Adjustment)
FM ANTENNA terminal
(75
(75
Ω
)
75
Ω
coaxial
set
FM RF SSG
Carrier frequency : 69 MHz
Output level
Output level
: 1 mV (60 dBµ) (at 75
Ω
open)
Modulation
: AUDIO 1 kHZ, 10 kHz deviation
Connection 2:
FM ANTENNA terminal
(75
(75
Ω
)
75
Ω
coaxial
set
FM RF SSG
AF OSC
Audio 31.25 kHz
external
modulation
terminal
modulation
terminal
Carrier frequency : 69 MHz
Output level
Output level
: 1 mV (60 dBµ) (at 75
Ω
open)
Modulation
: AUDIO 31.25 kHZ, 10 kHz deviation
(EXTERNAL MODULATION)
Adjustment Location :
EE, CIS model :
EE, CIS model :
[TCB BOARD] (Component Side)
RV41
IC1701
RV42
RV1701
CT1701
TP1702
(VCO)
(VCO)
(FILTER) TP1701
TM1
FE1
+
–
–
FREQUENCY COUNTER
+
–
–
LEVEL METER
IC41
L1701
RV1702
RV41
AM tuned level
Adjustment
AM tuned level
Adjustment
RV1701, TP1701
Sub carrier level
Adjustment
Sub carrier level
Adjustment
RV1702, TP1702
VCO Adjustment
VCO Adjustment
RV42
FM tuned level
Adjustment
FM tuned level
Adjustment
CT1701, L1701, TP1701
Sub carrier peak
Adjustment
Sub carrier peak
Adjustment
• Abbreviation
EE: East European model
– 35 –
CD SECTION
Note:
1. CD Block is basically designed to operate without adjustment.
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent
3. Use an oscilloscope with more than 10M impedance.
4. Clean the object lens by an applicator with neutral detergent
when the signal level is low than specified value with the fol-
lowing checks.
lowing checks.
5. Adjust the focus bias adjustment when optical block is replaced.
Focus Bias check
Procedure:
1. Connect oscilloscope to test point TP (RF). (GND terminal :
1. Connect oscilloscope to test point TP (RF). (GND terminal :
VC)
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that the shape “≈” can be clearly distinguished at the
3. Put disc (YEDS-18) in and playback.
4. Confirm that the shape “≈” can be clearly distinguished at the
center of the waveform and check the RF signal level.
• RF signal
S Curve Check
Procedure:
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
1. Connect oscilloscope to test point TP (FEO).
2. Connect between test point TP (FOK) and GND by lead wire.
3. Turn Power switch on.
4. Put disc (YEDS-18) in and turned Power switch on again and
actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
table is moving in and out.)
5. Check the oscilloscope waveform (S-curve) is symmetrical be-
tween A and B. And confirm peak to peak level within 3±1 Vp-p.
S-curve waveform
6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of
Note: • Try to measure several times to make sure than the ratio of
A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the bright-
ness to obtain best waveform.
RF Level Check
Procedure:
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig-
1. Connect oscilloscope to test point TP (RF) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF sig-
nal level is correct or not.
Note:
Clear RF signal waveform means that the shape “≈” can be
clearly distinguished at the center of the waveform.
clearly distinguished at the center of the waveform.
• RF signal
+
–
–
BD board
TP (FEO)
TP (VC)
TP (VC)
oscilloscope
+
–
–
BD board
TP (RF)
VC
oscilloscope
(DC range)
A
B
symmetry
within 3
±
1 Vp-p
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
TIME/DIV: 500 ns
level:
1.3
1.3
±
0.3 Vp-p
VOLT/DIV: 200 mV
TIME/DIV: 500 ns
TIME/DIV: 500 ns
level:
1.3
1.3
±
0.3 Vp-p
+
–
–
BD board
TP (RF)
TP (VC)
TP (VC)
oscilloscope
– 36 –
E-F Balance (1 Track Jump) check
(Without remote commander)
(Without remote commander)
Procedure:
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the “
1. Connect oscilloscope to test point TP (TEO) on BD board.
2. Turned Power switch on.
3. Put disc (YEDS-18) in to play the number five track.
4. Press the “
P (Pause)” button. (Becomes the 1 track jump mode)
5. Check the level B of the oscilloscope's waveform and the A (DC
voltage) of the center of the Traverse waveform.
Confirm the following:
Confirm the following:
A – B
2 (A + B)
×
100 = ±7 (%)
1 track jump waveform
Adjustment Location:
[BD BOARD] (Conductor Side)
+
–
–
BD board
TP (TEO)
TP (VC)
TP (VC)
oscilloscope
IC103
CNU102
IC101
IC
I02
I02
RF
FOK
VC
FEO
TEO
GND
CNU101
GND
Center of the waveform
B
level : 500 mV
±
100 mVp-p
symmetry
A (DC voltage)
0V
Click on the first or last page to see other HCD-RX80 / MHC-RX80 service manuals if exist.