Sony HCD-GZX33D / HCD-GZX55D / HCD-GZX88D Service Manual ▷ View online
HCD-GZX33D/GZX55D/GZX88D
13
SECTION 3
TEST MODE
[PANEL TEST MODE]
•
•
This mode is used to check the fl uorescent indicator tube,
LEDs, keys, [MASTER VOLUME/DJ CONTROL] jog,
model, destination and software version.
LEDs, keys, [MASTER VOLUME/DJ CONTROL] jog,
model, destination and software version.
Procedure:
1. Press [ENTER] button and [MUSIC] button simultaneously
and hold 3 seconds.
2. All LEDs and segments in fl uorescent indicator tube are
lighted up. All RGB LEDs are lighted up in white color.
3. When you want to enter to the software version display mode,
press [+ PRESET+] button.
** If display shown information below, please proceed
with [MODEL & DEST WRITE] mode to write model &
destination.
with [MODEL & DEST WRITE] mode to write model &
destination.
“GSX8D(T)” is shown for HCD-GZX33D/GZX55D/GZX88D.
The model information appears on the fl uorescent indicator
tube.
tube.
•
“GSX3D” is shown for HCD-GZX33D.
•
“GSX5D” is shown for HCD-GZX55D.
•
“GSX8D” is shown for HCD-GZX88D.
Press
[+ PRESET+] button again to view the destination
information.
4. During the destination information display, press [+
PRESET+] button. Each time [+ PRESET+] button is
pressed, the fl uorescent indicator tube shows the version of
each category software in the following sequence: SC, MTK,
UI, PF, SYS, CD, CDMA, CDMB, ST, TA, TAS, TM, BTM,
BT, NFC, and return back to model information display.
pressed, the fl uorescent indicator tube shows the version of
each category software in the following sequence: SC, MTK,
UI, PF, SYS, CD, CDMA, CDMB, ST, TA, TAS, TM, BTM,
BT, NFC, and return back to model information display.
5. When
[ ] button is pressed while the version numbers are
being displayed except model and destination, the date of
the software creation appears. When [ ] button is pressed
again, the display returns to the software version display.
the software creation appears. When [ ] button is pressed
again, the display returns to the software version display.
6. Press [– PRESET–] button, the key check mode is activated.
7. In the key check mode, the fl uorescent indicator tube displays
7. In the key check mode, the fl uorescent indicator tube displays
“K 0 V0”.
Each time a button is pressed, “K” value increases. However,
once a button has been pressed, it is no longer taken into
account.
once a button has been pressed, it is no longer taken into
account.
“V” value increases in the manner of 0, 1, 2, 3 ... if [MASTER
VOLUME/DJ CONTROL] knob is turned clockwise, or it
decreases in the manner of 0, 9, 8, 7 ... if [MASTER VOLUME
/ DJ CONTROL] knob is turned counterclockwise.
VOLUME/DJ CONTROL] knob is turned clockwise, or it
decreases in the manner of 0, 9, 8, 7 ... if [MASTER VOLUME
/ DJ CONTROL] knob is turned counterclockwise.
8. When [ENTER] button is pressed after all LEDs and segments
in fl uorescent indicator tube light up, alternate segments in
fl uorescent indicator tube and LEDs would light up, all RGB
LEDs would light up in red color. If you press [ENTER]
button again, another half of alternate segments in fl uorescent
indicator tube and LEDs would light up, all RGB LEDs would
light up in green color. Pressing [ENTER] button again
would cause all segments in fl uorescent indicator tube and
LEDs light up, all RGB LEDs would light up in blue color.
Pressing [ENTER] button again would turn off all segments
in fl uorescent indicator tube and all LEDs including RGB
LEDs.
fl uorescent indicator tube and LEDs would light up, all RGB
LEDs would light up in red color. If you press [ENTER]
button again, another half of alternate segments in fl uorescent
indicator tube and LEDs would light up, all RGB LEDs would
light up in green color. Pressing [ENTER] button again
would cause all segments in fl uorescent indicator tube and
LEDs light up, all RGB LEDs would light up in blue color.
Pressing [ENTER] button again would turn off all segments
in fl uorescent indicator tube and all LEDs including RGB
LEDs.
9. To release from this mode, press the buttons in the same
manner as step 1, or disconnect the power cord.
[USER RESET]
• The user reset clears all data including preset data stored in
• The user reset clears all data including preset data stored in
the data fl ash to initial conditions exclude history mode data.
Procedure:
1. Press
[&/1] button to turn on the system.
2. Press
[ ] button and [LED COLOR] button simultaneously
for 3 seconds.
3. “RESET” appears on the fl uorescent indicator tube. After
that, the fl uorescent indicator tube becomes blank for a while,
and the system is reset.
and the system is reset.
[COLD RESET]
• The cold reset clears all data including preset data stored in
• The cold reset clears all data including preset data stored in
the data fl ash to initial conditions included history mode data.
Execute this mode when returning the set to the customer.
Execute this mode when returning the set to the customer.
Procedure:
1. Press
[&/1] button to turn on the system.
2. Press
[ ] button and [AUDIO IN] button simultaneously for
3 seconds.
3. “COLD RESET” appears on the fl uorescent indicator tube.
After that, the fl uorescent indicator tube becomes blank for a
while, and the system is reset.
while, and the system is reset.
[CD/DVD SHIP MODE (WITH MEMORY CLEAR)]
• This mode moves the optical pick-up to the position durable
• This mode moves the optical pick-up to the position durable
to vibration and clears all data including preset data stored in
the data fl ash to initial conditions during the next AC-In. Use
this mode when returning the set to the customer after repair.
the data fl ash to initial conditions during the next AC-In. Use
this mode when returning the set to the customer after repair.
Procedure:
1. Press
[\/1] button to turn on the system.
2. Select DVD/CD function.
3. Press [DVD/CD] and [SOUND FLASH] button simultaneously
3. Press [DVD/CD] and [SOUND FLASH] button simultaneously
for 3 seconds. The system turns off automatically.
4. A message “MECHA LOCK” is displayed on the fl uorescent
indicator tube and the CD/DVD ship mode is set.
[CD/DVD TRAY LOCK MODE]
• This mode let you lock the disc tray. When this mode is
• This mode let you lock the disc tray. When this mode is
activated, the disc tray will not open when [ZOPEN/CLOSE]
button is pressed. The message “LOCKED” will be displayed
on the fl uorescent indicator tube. This mode only applied
when there is disc(s) on the tray.
button is pressed. The message “LOCKED” will be displayed
on the fl uorescent indicator tube. This mode only applied
when there is disc(s) on the tray.
Procedure:
1. Press
[\/1] button to turn on the system.
2. Select DVD/CD function.
3. Press
3. Press
[ ] button and [ENTER] button simultaneously and
hold down until “LOCKED” or “UNLOCKED” displayed on
the fl uorescent indicator tube (around 5 seconds).
the fl uorescent indicator tube (around 5 seconds).
[CDM AGING MODE]
•
•
This mode is used for CDM aging.
Procedure:
1. Press
[\/1] button to turn on the system.
2. Select DVD/CD function.
3. Open the disc tray, insert a disc and close the tray.
4. Press [DVD/CD] button and [BASS BAZUCA] button
3. Open the disc tray, insert a disc and close the tray.
4. Press [DVD/CD] button and [BASS BAZUCA] button
simultaneously for 3 seconds.
5. The fl
uorescent indicator tube displays Aging Display
“AG xxxx/yyyy”.
“xxxx” represents the error counter
(Maximum Value of “xxxx” = 9999)
“yyyy” represents the cycle counter
(Maximum Value of “yyyy” = 9999)
6. Press
[+ PRESET+] or [– PRESET–] to search for Aging
History Error Display.
The
fl uorescent indicator tube displays “Mx E1E2E3E4”.
x: error history number
E1: Loading sequence JCP high
E2: Loading sequence JCP low
E3: Loading operation JCP
E4: Cam position operation JCP
7. Press [ENTER] to Aging Display
To release from this mode, press [\/1] button or perform COLD
RESET operation.
RESET operation.
HCD-GZX33D/GZX55D/GZX88D
14
[HISTORY MODE]
•
•
This mode is used to check important data stored in the system
when PROTECTOR happen.
when PROTECTOR happen.
Procedure:
1. During demo mode, press [ENTER] button and [LED
PATTERN] for 5 seconds to mode in to history mode.
2. Press the [TUNING + >] or [TUNING – .] button to
check history data stored.
To release from this mode, press [\/1] button.
Display on fl uorescent indicator tube
Description
P
R
O
C
O
U
N
T
※ ※
No of time protector happen (0 ~ 99)
P
R
O
T
Y
P
E
※ ※ ※ ※
Indication protector type (refer protector kind test mode)
Protector type
Protector Error Code
AMPL
E01
PWR2
E03
SPK
E04
TEMP
E05
FAN
E06
T
1
※ ※ ※ ※ ※
H
※ ※
M
Single Power On Time until protector happened
(0~99999 hours, 0~99Min)
(0~99999 hours, 0~99Min)
T
2
※ ※ ※ ※ ※
H
※ ※
M
Total Power On Time [ no consider protector happen ]
(0~99999 hours, 0~99Min)
(0~99999 hours, 0~99Min)
F
U
N
C
※ ※ ※ ※ ※ ※ ※
Input Function during protector happened
V
O
L
※ ※ ※
Volume setting (MIN / 1 - 50 / MAX)
A
T
T
※ ※ ※
Actual attenuation (-87 … 0)
E
Q
L
O
W
※ ※ ※
Low EQ level (-6 … 0 … +6)
E
Q
M
I
D
※ ※ ※
Mid EQ level (-6 … 0 … +6)
E
Q
H
I
G
H
※ ※ ※
High EQ level (-6 … 0 … +6)
V
A
C
S
※ ※
VACS level (0 ... 5)
A
P
V
A
C
S
※ ※
AP VACS level (0 … 7)
S
W
※ ※ ※
Subwoofer setting (OFF / 0 / 4 / 7 / 10)
S
U
R
R
※ ※ ※
Surround setting (OFF / ON)
D
J
※ ※ ※ ※ ※ ※
※ ※
DJ Effect setting
DJ Mode: OFF/ISOLAT/FLANGE/PHASER/FLASH
DJ Setting Value: 1~ 40
DJ Mode: OFF/ISOLAT/FLANGE/PHASER/FLASH
DJ Setting Value: 1~ 40
B
A
Z
U
C
A
※ ※ ※
Bass Bazuca setting (OFF / ON)
HCD-GZX33D/GZX55D/GZX88D
15
[PROTECT KIND CHECK TEST MODE]
• This mode is used to check types of protect occurred during
• This mode is used to check types of protect occurred during
protector on.
Procedure:
1. During protection on, fl uorescent indicator tube shows
blinking message “PROTECT EXX” where “EXX” represent
the error code.
the error code.
2. Press
[ ] button & [PRESET– –] button simultaneously.
3. Fluorescent indicator tube display will toggle between
“PROTECT” message & protector kind message display.
Below table explains on protector kind.
Below table explains on protector kind.
Error
Code
Code
Protector Message
Description
E01
“AMP OCP”
The over current condition to
MOSFET occurs by defect
of MOSFET or defect of PS
output line.
MOSFET occurs by defect
of MOSFET or defect of PS
output line.
E03
“POWER SUPPLY”
Defect of power supply circuit
to AMP
to AMP
E04
“DC DETECT”
DC appears in SP terminal
by defect of AMP IC and
MOSFET.
by defect of AMP IC and
MOSFET.
E05
“THERMISTOR”
Unusual heat up of MOSFET
by improper assembly of heat
sink, destruction of MOSFET
etc.
by improper assembly of heat
sink, destruction of MOSFET
etc.
E06
“FAN BLOCK”
Defect of DC FAN and DC
FAN driver circuit
FAN driver circuit
To release from this mode:
Press [] button & [PRESET– –] button simultaneously again
or unplug & re-plug in the power cord.
Press [] button & [PRESET– –] button simultaneously again
or unplug & re-plug in the power cord.
If speaker does not have output even if the set status is not in
PROTECT mode, the following defect might be possible:
PROTECT mode, the following defect might be possible:
Defects
Possible cause
RESET defect
Reset signal status from micom is not ‘H’.
If the PROTECT mode is “POWER SUPPLY”, there is
possibility of unusual power supply of any of the AMP IC or
Pre-amplifi er.
Pre-amplifi er.
[MODEL & DEST WRITE MODE]
•
•
This mode is used to set software model & destination.
• This mode is only available when no permanent model &
destination is stored.
Procedure:
1. Press [ENTER] button & [FOOTBALL] button simultaneously
and hold for 5 seconds.
2. Fluorescent indicator tube display will show “M XXXXX”.
3. Press
3. Press
[+ PRESET+] / [PRESET– –] button to select the
model based on the set’s model.
Product Code
F. Tube display
HCD-GZX33D
“M GSXD3”
HCD-GZX55D
“M GSXD5”
HCD-GZX88D
“M GSXD8”
4. Press [ENTER] button.
5. Fluorescent indicator tube display will show “D XXXXX”.
6. Press
5. Fluorescent indicator tube display will show “D XXXXX”.
6. Press
[+ PRESET+] / [PRESET– –] button to select the
destination based on the set’s country.
Area Code
Country
F. Tube display
J1
Japan
“D J”
JE1
Tourist
“D JE”
U2/CA2
America, Canada
“D NA”
CEL/CE1/
CE2
CE2
Europe (general)
“D CE2”
CEK
U.K.
“D CEK”
RU1/RU3
Russia
“D RU”
AU1
Australia
“D AU”
CN1
China
“D CN”
E12
India, Pakistan, Morocco
“D E12”
E3/E93/
SA2/E15
SA2/E15
Middle East, Africa
(South Africa), Iran
(South Africa), Iran
“D E3”
E4
Africa
“D E12”
EA3
Saudi Arabia
“D EA3”
HK1/
HK2/PL1/
SP1/SP2/
SP6/TH1
HK2/PL1/
SP1/SP2/
SP6/TH1
Hong Kong, Philippines,
Singapore, Malaysia,
Thailand
Singapore, Malaysia,
Thailand
“D ASIA”
KR2
Korea
“D KR”
TW2
Taiwan
“D TW”
E2, E32,
E51, AR2
E51, AR2
Latin America (general),
Chile, Peru, Argentina
Chile, Peru, Argentina
“D LATIN”
BR1
Brazil
“D BR”
MX2,
MX4
MX4
Mexico
“D MX”
7. Press [ENTER] button to confi rm the selection.
8. “RESET” appears on the fl uorescent indicator tube. After that,
8. “RESET” appears on the fl uorescent indicator tube. After that,
the fl uorescent indicator tube becomes blank for a while, and
the system is reset.
the system is reset.
9. Mode in [PANEL TEST MODE] again to confi rm on the
model & destination.
HCD-GZX33D/GZX55D/GZX88D
16
[DVD COLOR SYSTEM MODE]
•
•
This mode let you change the color system of the video output
from PAL to NTSC or vice-versa.
from PAL to NTSC or vice-versa.
Procedure:
1. Press the [\/1] button to turn on the system.
2. Press the [DVD/CD] button.
3. Press the [DVD/CD] button and [LED COLOR] button
2. Press the [DVD/CD] button.
3. Press the [DVD/CD] button and [LED COLOR] button
simultaneously and hold for 3 seconds.
4. The message “COLOR PAL” or “COLOR NTSC” appears on
the fl uorescent indicator tube.
•
To release from DVD Color System Mode
1. Once the color system has been selected, the mode is fi xed
there after. If you wish to change the mode again, perform the
above item 2 again.
above item 2 again.
[DVD SERVICE MODE]
• This mode let you make diagnosis and adjustment easily by
• This mode let you make diagnosis and adjustment easily by
using the remote commander and the TV. The instructions,
diagnostic results, etc. are given on the on-screen display.
diagnostic results, etc. are given on the on-screen display.
•
TEST DISC LIST
Be sure to use the DVD disc that matches the signal standards
of your region.
of your region.
• CD
YEDS-18
(Part No.: 3-702-101-01)
PATD-012
(Part No.: 4-225-203-01)
• DVD SL (Single Layer)
NTSC : HLX-503 (Part No.: J-6090-069-A)
HLX-504 (Part No.: J-6090-088-A)
PAL :
HLX-506 (Part No.: J-6090-077-A)
• DVD DL (Double Layer)
NTSC : HLX-501 (Part No.: J-6090-071-A)
HLX-505 (Part No.: J-6090-089-A)
PAL :
HLX-507 (Part No.: J-6090-078-A)
•
Procedure to enter to DVD Service Mode:
1. Press the [\/1] button to turn on the system.
2. Press the [DVD/CD] button.
3. Press the [DVD/CD] button and [+ PRESET+] button
2. Press the [DVD/CD] button.
3. Press the [DVD/CD] button and [+ PRESET+] button
simultaneously and hold 3 seconds.
4. The message “SERVICE IN” appears on the fl uorescent
indicator tube.
The display of the “Model Name” of the “Remocon Diagnosis
Menu” change with the model and the destination appears on
screen display. Refer to below on the model name.
Menu” change with the model and the destination appears on
screen display. Refer to below on the model name.
HCD-GZX88D:
GSX8D
HCD-GZX55D:
GSX5D
HCD-GZX33D:
GSX3D
*1: Changes depending on destination
5. To execute each function, press its number by using numeric
button on the remote commander.
6. To release from this mode, press the [\/1] button to turn off
the system.
•
Execute IOP Measurement
In order to execute IOP measurement, the following standard
procedures must be followed.
procedures must be followed.
1. From the Top Menu of Remocon Diagnosis Menu, select
“2. Drive Manual Operation” by pressing the [2] button on
the remote commander. The following screen appears on the
onscreen display.
the remote commander. The following screen appears on the
onscreen display.
2. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The following screen appears on the
on-screen display.
on-screen display.
3. Select “6. Iop:” by pressing the [6] button on the remote
commander.
4. Wait until a hexadecimal number appears in the on-screen
display as below:
5. Convert data from hexadecimal to decimal by using
conversion table.
6. Please
fi nd the label on the rear of the BU (Base Unit).
The default IOP value is written in the label.
7. Subtract between these two values.
8. If the remainder is smaller than 93 (decimal), then it is OK.
8. If the remainder is smaller than 93 (decimal), then it is OK.
However if the value is higher than 93, then the BU is defective
and need to be change.
and need to be change.
9. Press the [RETURN] button on the remote commander to
return to previous menu.
10. Press the [0] button on the remote commander to return to the
Top Menu of Remocon Diagnosis Menu.
11. Press the [\/1] button to turn off the system.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
Model Name
IF-con
Syscon
IF-con
Syscon
: GSX8D_ XX
*1
: Ver. XX.XX (XXXX)
: Ver. X.XXX
: Ver. X.XXX
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu
2. Track/Layer Jump
3. Manual Adjustment
4. Mecha test mode
5. MIRR time Adjust
0. Return to Top Menu
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:
O
o Change Value
RETURN Return to previous menu
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eg Boost Adjust:
6. Iop. ED
7. TRV. Level:
8. S curve (FE) Level:
9. RFL (PI) Level:
0. MIRR Time:
O
o Change Value
RETURN Return to previous menu
Click on the first or last page to see other HCD-GZX33D / HCD-GZX55D / HCD-GZX88D service manuals if exist.