DOWNLOAD Sony HCD-GX90D / HCD-RV800D Service Manual ↓ Size: 98.94 KB | Pages: 9 in PDF or view online for FREE

5

Disc Type

Disc Type Select

 1. Disc Type Auto Check

 2. Set Disc Type DVD

 3. Set Disc Type CD

 4. Set Disc Type Hybrid

Exit: RETURN

2-1-1.

Disc Type Auto Check

1)

Press the 

[1]

 key on the remote commander to display the Disc

Type Auto Check screen.

2)

Insert a disc and press the 

[ENTER]

  key on the remote

commander.

3)

It judges the type of inserted disc automatically and displays
the disc type and so on as below.

Disc Type Auto Check

 Disc Type

xx

 Layer

xx

 Mirr Time

xx

 Mirr Count

xx

 FZC Count

xx

 PI Reference

xx

 PI Peak xx

 ENTER.Execute

Exit: RETURN

Disc Type

: CD, DVD or Hybrid (SACD)

Layer

: SINGLE, DUAL or HYBRID

Mirr Time

: Mirror time of between disc surface and record

surface when disc type judgment. (hexadecimal
number)

Mirr Count : The number of times which mirror counts between

disc surface and record surface when disc type
judging.

FZC Count : The number of times which focus zero cross points

of each layer when lens down.

PI Reference : The average of PI reference voltage. (hexadecimal

number)

PI Peak

: PI peak level voltage. It performs only when disc

type judgment is successful. (hexadecimal number)

2-1-2.

Disc Type DVD

It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]

: DVD single layer disc (12 cm)

[2]

: DVD dual layer disc (0 layer, 12 cm)

[3]

: DVD dual layer disc (1 layer, 12 cm)

[4]

: DVD-RW disc (12 cm)

[5]

: DVD single layer disc (8 cm)

[6]

: DVD dual layer disc (0 layer, 8 cm)

[7]

: DVD dual layer disc (1 layer, 8 cm)

[8]

: DVD-RW disc (8 cm)

2-1-3. Disc Type CD
It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]

: CD disc (normal speed, 12 cm)

[2]

: CD disc (double speed, 12 cm)

[3]

: CD disc (normal speed, 8 cm)

[4]

: CD disc (double speed, 8 cm)

[5]

: CD-RW disc (normal speed, 12 cm)

[6]

: CD-RW disc (double speed, 12 cm)

[7]

: CD-RW disc (normal speed, 8 cm)

[8]

: CD-RW disc (double speed, 8 cm)

2-1-4.

Disc Type Hybrid

It sets up so that it may judge as a disc type of specification of the
disc with which the set was inserted.

[1]

: SACD Hybrid disc (SACD layer, 12 cm)

[2]

: SACD Hybrid disc (CD layer, normal speed, 12 cm)

[3]

: SACD Hybrid disc (CD layer, double speed, 12 cm)

[4]

: SACD Hybrid disc (SACD layer, 8 cm)

[5]

: SACD Hybrid disc (CD layer, normal speed, 8 cm)

[6]

: SACD Hybrid disc (CD layer, double speed, 8 cm)

 Be sure to perform the disc type setup before performing this item.

Servo Control

 1.LD

off R.Sled FWD

 2.Focus

off L.Sled REV

 3.SPDL

off U.Sled Reset

 4.CLVA

off D.Sled Limit

 5.Trk.

off

 6.Sled

off

 7.Fcs.Srch

off

 8.Fcs.OppL

off

 0.All Servo Off

Exit: RETURN

On this screen, the servo on/off control necessary for replay is
executed. Normally, turn on each servo from 1 sequentially and
when CLVA is turned on, the usual trace mode becomes active. In
the trace mode, DVD sector address or CD time code is displayed.
This is not displayed where the spindle is not locked.
The spindle could run overriding the control if the spindle system is
faulty or RF is not present. In such a case, do not operate CLVA.

[1]

 LD

: Turn on/off the laser.

[2]

 Focus

: Search the focus and turn on the focus.

[3]

 SPDL

: Turn on/off the spindle.

[4]

 CLVA

: Turn on/off normal servo of spindle servo.

[5]

 Trk.

: Turn on/off the tracking servo.

[6]

 Sled

: Turn on/off the sled servo.

[7]

 FCS. Srch : Turn on/off the focus search.

[8]

 FCS. OppL : Turn  on/off  the  focus search to another

(opposite) layer of designated layer in Disc
Type setting. (dual layer disc only)

[10/0]

: All servo off.

[R]

 Sled FWD (right cursor) : Move the sled forward.

[L]

 Sled REV (left cursor)

: Move the sled reverse.

[U]

 Sled FWD (up cursor)

: Reset the sled.

[D]

 Sled REV (down cursor) : Limit in the sled.

6

Track/Layer Jump

 1.  1Tj

FWD R.Lj L0>L1

 2.  1Tj

REV L.Lj L1>L0

 3.500Tj Fine

FWD U.Fj L0>L1

 4.500Tj Fine

REV D.Fj L1>L0

 5.10kTj Dirc

FWD

 6.10kTj Dirc

REV

 7.20kTj Dirc

FWD

 8.20kTj Dirc

REV

 0. All Servo Off

Exit: RETURN

On this screen, track jump, etc. can be performed. Only for the DVD
dual layer disc, the focus jump and layer jump are displayed in the
right field

[1]

 1Tj FWD

: 1 track jump forward.

[2]

 1Tj REV

: 1 track jump reverse.

[3]

 500Tj FWD: 500 track jump (fine search)forward.

[4]

 500Tj REV : 500 track jump (fine search) reverse.

[5]

 10kTj FWD: 10k track jump (direct search) forward.

[6]

 10kTj REV : 10k track jump (direct search) reverse.

[7]

 20kTj FWD: 20k track jump (direct search) forward.

[8]

 20kTj REV : 20k track jump (direct search) reverse.

[10/0]

: All servo off.

Non EEPROM Write Adjust

 1. Focus Offset

 2. Focus Gain

 3. Trk.

Offset Coarse

 4. Trk.

Offset Fine

 5. Trk.

Gain

 6. EQ

Boost

 0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted manually. Select the desired
number 

[1]

  to 

[10/0]

  from the remote commander, and current

setting for the selected item will be displayed, then increase or
decrease numeric value with the O key or  o key. This value is
stored in the EEPROM. If CLV has been applied, the jitter is
displayed for reference for the adjustment.

[1]

 Focus Offset : Adjusts focus offset.

[2]

 Focus Gain : Adjusts focus gain.

[3]

 TRK. Offset : Adjusts tracking offset of the RF amp

(IC001) side.

[4]

 TRK. Offset : Adjusts tracking offset of the DSP (IC401)

side.

[5]

 TRK. Gain : Adjusts track gain.

[6]

 EQ Boost

: Adjusts amount of boost of equalizer.

[10/0]

: All servo off.

EEPROM Write Adjust

 1. Focus

Offset

 2. Focus

Gain

 3. Trk.

Offset Coarse

 4. ——————

 5. Trk.

Gain

 6. EQ

Boost

 0.All Servo Off

Exit: RETURN

On this screen, each item can be adjusted automatically. Select the
desired number 

[1]

  to 

[10/0]

  from the remote commander, and

selected item is adjusted automatically.

[1]

 Focus Offset : Adjusts focus offset.

[2]

 Focus Gain : Adjusts focus gain.

[3]

 TRK. Offset : Adjusts tracking offset of the RF amp

(IC001) side.

[5]

 TRK. Gain : Adjusts track gain.

[6]

 EQ Boost

: Adjusts amount of boost of equalizer.

[10/0]

: All servo off.

Display images are shown as follows, and all two screens are able
to switch by the O key (UP) or  o key (DW).

EEPROM Data 1/2

CD

SL

L0

L1

Focus

Gain

xx

xx

xx

xx

Trk.

Gain

xx

xx

xx

xx

Focus

Offset

xx

xx

xx

xx

Trk.

Offset

xx

xx

xx

xx

EQ.

Boost

xx

xx

xx

xx

PI

Level

xx

xx

--

--

Fcs. Balance

--

xx

--

--

Jitter xx

xx

xx

xx

Mirror Time

xx

xx

xx

--

FE Level

--

xx

--

--

Traverse Lv1.

--

xx

--

--

Next:DW Default:CLR

Exit:RET

EEPROM Data 2/2

CDRW DVDRW

Focus

Gain

xx

xx

Trk.

Gain

xx

xx

Focus

Offset

xx

xx

Trk.

Offset

xx

xx

EQ.

Boost

xx

xx

Next:UP Default:CLR

Exit:RET

On this screen, current servo adjusted data stored in the EEPROM
are displayed. The adjusted data are initialized by pressing the

[CLEAR]

  key,  but be careful that they are not recoverable after

initialization.
Before clearing the adjusted data, make a note of the set data. This
screen will also appear if 

[0]

-All is selected in the Drive Auto

Adjustment. In this case, default setting cannot be made.

7

Disc Check Memory

 1. SL Disc check

 2. SL Disc check

 3. SL Disc check

Exit: RETURN

On this screen, measure the mirror time of chucked disc, and write
to the EEPROM.

Error Rate Display

UC

CR

Address

PI1 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

PI2 Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

PO  Err

Now xx xxxx xxxxxxxx

Max xx xxxx xxxxxxxx

Avg xx xxxx xxxxxxxx

Exit: RETURN

On this screen, measure and display the error rate.

UC : Incorrect value
CR : Correct value

SACD Water Mark Check

 PSP AMP

 PSN

 Start: ENTER

Exit: RETURN

On this screen, measure the PSP AMP value and PSN value of SACD
water mark.

On the Test Mode Menu screen, selecting 

[3]

 executes the aging of

the mechanism deck.

### Aging Test MENU ###

Operation Menu

1. Open/Close Test

Exit: RETURN

1)

On the Aging Test MENU screen, press the 

[1]

  key  on the

remote commander to display the Open/Close Test screen.

2)

Insert discs and press the 

[ENTER]

  key on the remote

commander.

3)

Is starts the aging.
During aging, the disc number, operating status and repeat cycle
are displayed. Aging can be aborted at any time by pressing
the

x

key. After the operation is stopped, press the

x

key or

[RETURN]

 key aging to return to the Aging Test MENU.

On the Test Mode Menu screen, selecting 

[4]

  displays the

information such as servo emergency history.
The history information from last 1 up to 10 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.

### EMG. History ###

  Laser Hours

CD

xxxxhxxm

DVD

xxxxhxxm

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

a.

bb xx xx xx  xx xx xx xx

xx xx xx xx  xx xx xx xx

   Select:1-9

Scroll:UP/DOWN

  (1.Latest EMG.)

Exit: RETURN

xxxxhxxm : The laser on total hours. Data below minutes are

omitted.

a.

: Error number.

bb

: Error code.

xx

: Not used.

• Clearing History Information

Press the 

[DVD DISPLAY]

 and 

[CLEAR]

 keys in this order.

Then both CD and DVD data are cleared.

Press the 

[DVD TOP MENU]

 and 

[CLEAR]

 keys in this order.

Press 

[DVD MENU]

 and 

[CLEAR]

 keys in this order.

The data have been initialized when “Set Up Initialized”
message is displayed. The EMG. History screen will be restored

8

soon.

• Code list of Emergency History

10: Communication to RF AMP (IC001) failed.
11: Each servo for focus, tracking, and spindle is unlocked.
12: Check sum error of EEPROM (IC203).
14: Communication to servo DSP (IC401) failed, or servo DSP

decoder (IC801) is faulty.

15: Communication to DVD decoder (IC701) failed, or DVD

decoder (IC801) is faulty.

16: Communication to DSD decoder (IC801) failed, or DSD

decoder (IC801) is faulty.

20: Initialization of sled servo failed. It is not placed in the ini-

tial position.

23: Sled servo operation error.
24: Made a request to move the sled servo to wrong position.
30: Tracking balance adjustment error.
31: Tracking gain adjustment error.
33: Focus bias adjustment error.
34: Focus gain adjustment error.
35: Equalizer adjustment error.
40: Focus servo does not operate.
41: With a DVD dual layer disc, focus jump failed.
50: CLV (spindle) servo does not operate.
51: Spindle does not stop.
60: Made a request to seek nonexistent address.
61: Seek error of retry more than regulated times.
70: Control data could not be read.
80: Disc reading failed.

On the Test Mode Menu screen, selecting 

[5]

 displays the information

of mechanism deck error history.
The history information from last 1 up to 8 can be scrolled with
the O key or o key. Also, specific information can be displayed
by directly entering that number with ten keys.

### Mecha Error History ###

  1. aa bb cc xx xx xx xx xx

  2. aa bb cc xx xx xx xx xx

  3. aa bb cc xx xx xx xx xx

  4. aa bb cc xx xx xx xx xx

  5. aa bb cc xx xx xx xx xx

  6. aa bb cc xx xx xx xx xx

  7. aa bb cc xx xx xx xx xx

  8. aa bb cc xx xx xx xx xx

Scroll:UP/DOWN

(1.Latest Err.)

Exit: RETURN

aa: Initialization is completed or not.

FF

: Complete.

other number : Not complete.

bb: Operating status of mechanism deck at an error occurred.

(lod sq jcp)
00

: Initializing.

10 to 15 : Open operating.
16 to 19 : Kicking cause open failed.
1A to 1F : Open operating.
20 to 27 : Complete the open operation.
28

: No disc and complete the open operation.

29 to 2F : Complete the open operation.
30 to 3F : Close requesting.
40 to 4F : Open requesting.
50 to 5F : Close operating.
60 to 6F : Complete the chucking operation.
80 to 8F : Complete the release operation.

(BU is home position)

90 to 9F : BU down operating.
A0 to AF : Opening/closing the shutter. Or stationary state in

open/close the shutter is enablement.

B0 to BF : BU up requesting.
C0 to CF : BU down requesting.
D0 to DF : BU upping.
E0 to EF : No disc checking in disc loading.

cc: Operating status of mechanism deck at an error occurred.

(lod oq jcp)
00

: Complete the operation.

10 to 1F : Open operating.
20 to 2F : Close operating.
30 to 3F : Release operating.
60 to 6F : Chucking operating.
70 to 7F : Kicking operating.
80 to 8F : Returning the BU to home position. (after kicking)