DOWNLOAD Sony HCD-GX750 / HCD-RG551 / HCD-RX550 / MHC-GX750 / MHC-RG551S Service Manual ↓ Size: 7.53 MB | Pages: 76 in PDF or view online for FREE

17

6

two coil springs 

     (insulator)

0

two coil springs 

     (insulator)

7

two insulators 

qa

two insulators 

8

two screws 

     (BVTT M2.6)

4

screw 

     (BVTT M2.6)

2

holder (213) ASSY

9

two stoppers (BU)

5

stopper (BU)

qd

optical pick-up

     (KSM-215DCP/C2NP)

3

floating screw

     (+PTPWH M2.6)

qs

1

floating screw 

     (+PTPWH M2.6)

2

tray

3

belt (table)

5

pulley (table)

8

screw

     (+BTTP (M2.6))

0

SENSOR board

7

gear (geneva)

1

floating screw 

     (+PTPWH M2.6)

6

floating screw 

     (+PTPWH M2.6)

4

floating screw 

     (+PTPWH M2.6)

9

CN731

18

6

Remove the two solderings of motor.

8

MOTOR (TB) board

7

table motor assy (M741)

5

two screws

     (+BTTP (M2.6))

4

1

stopper

2

stopper

3

CN742

4

Remove the two solderings of motor.

3

MOTOR (LD) board

1

belt (loading)

5

loading motor assy (M751)

2

two screws

     (+BTTP (M2.6))

19

• A step of AM channels can be changed over between 9 kHz and

10 kHz.

Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function “TUNER”, and press  TUNER/BAND

button to select the BAND “AM”.

3. Press ?/1 button to turn the set OFF.
4. Press  TUNER/BAND  and ?/1 buttons simultaneously, and

the display of  fluorescent indicator tube changes to “AM 9 k
STEP” or “AM 10 k STEP”, and thus the channel step is changed
over.

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning
the set to the customer.

Procedure:
1. Press three buttons x  ,  PLAY MODE/TUNING MODE  ,

and DISC 1 simultaneously.

2. The fluorescent indicator tube displays “COLD RESET” and

the set is reset.

This mode can be used for operation check of CD section and tape
deck section.
• If an error occurred:

The aging operation stops and is displayed status.

• If no error occurs:

The aging operation continues repeatedly.

1.

Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set three discs in tray.  Select ALL DISCS, and REPEAT OFF.
2) Load the tapes recording use into both decks.
3) Press three buttons x ,  PLAY MODE/TUNING MODE  ,

and  EX-CHANGE  simultaneously.

4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [Cold Reset].

2.

Aging mode in CD section

1) Operation during aging mode
• In the agining mode, the program is excuted in the following

sequence.

(1) The disc tray opens and closes.
(2) The disc tray turns to select a disc 3.
(3) The pick-up accesses to the first track, and plays 3 seconds.
(4) The pick-up accesses to the last track, and plays 3 seconds.
(5) The disc tray opens and closes.
(6) The disc tray turns to select a disc 1.
(7) The same operation starts like step (3).
(8) After a disc 1 aging operation, a disc 2 is selected.
(9) When an aging operation of a disc 3 is completed, the display

“AGING 

∗∗∗∗

” value increases.

(10) If no error occurs, the aging operation continues repeatedly.

2) Error display

Step

1

2

3

4

5

6

7

8

9

10

11

12

Operation

Rewind the TAPE A

Rewind the TAPE B

Play the TAPE A (1 minute)

Stop the TAPE A (1 second)

Play the TAPE A (3 minutes)

Rewind(AMS) the TAPE A

F.F.(AMS) the TAPE A

Play the TAPE B (1 minute)

Stop the TAPE B (1 second)

Record the TAPE B (3 minutes)

Rewind(AMS) the TAPE B

F.F.(AMS) the TAPE B

Display

TAPE

AAG-1

TAPE

BAG-2

TAPE

AAG-2

TAPE

AAG-3

TAPE

AAG-4

TAPE

AAG-5

TAPE

AAG-6

TAPE

BAG-2

TAPE

BAG-3

TAPE

BAG-4

TAPE

BAG-5

TAPE

BAG-6

Disc error

Display

Error

E00D01022

Focus error (No disc)

E00D02022

Sub Q error (Focus is good)

E00D02023

TOC reading error

E00D02014

Access error (Unable within regular time)

Mechanism error

Display

Error

E00M__E_0

Error during opening tray

E00M__C_2

EX-CHANGE disc error

E00M__D_0

Error during closing tray

E00M__F_3

EX-OPEN error

E00M__D_5

EX-CLOSE error

E00M__C_2

Chuck-up error

E00M__C_3

Unchucking error

3.

Aging mode in Tape Deck section

1) Operation during aging mode
• In the agining mode, the program is excuted in the following

sequence.

2) Error display
• If error occurred, the display remains like “TAPE BAG-2”.

4.

Exiting from the aging mode

• Be sure to perform Cold Reset to exit from the aging mode.

20

• This mode is used to test the function of the equalizer.

Procedure:
1. Press  ?/1  button to turn the set ON.
2. To enter the test mode, press the three buttons  x ,  PLAY

MODE/TUNING MODE  and  DISC 3  simultaneously.

3. Press the  EQ +  button.

The function of the equalizer is set to “MIN”.

4. Press the  EQ –  button.

The function of the equalizer is set to “MAX”.

5. Press the  PRESET EQ  button.

The function of the equalizer is set to “EQ FLAT”.

6. MASTER VOLUME  up and down.

“VOLUME MIN” “VOLUME 16” “VOLUME MAX” is
displayed.

7. Press the  GROOVE  button.

The message “VACS OFF” or “VACS ON” is displayed.

8. To exit from this mode, press  ?/1  button to turn the set OFF.

• This mode moves the pick-up to the position durable to vibra-

tion. Use this mode when returning the set to the customer after
repair.

Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function “CD”.
3. Press  ?/1  button to turn the set OFF.
4. Press  CD  button and  ?/1   button simultaneously.
5. The “STANDBY” display blinks instantaneously, and the CD

ship mode is set.

Procedure:
1.

Press  ?/1  button to turn the set ON.

2.

Select the function “CD”.

3.

Press  ?/1  button to turn the set OFF.

4.

Press three buttons  x  ,  CD  and  DISPLAY  simultaneously.

5.

The “STANDBY” display blinks instantaneously and CD ship
mode is set.

6.

To fluorescent indicator tube displays “COLD RESET” and
the set is reset.

Procedure:
1.

Press the  ?/1  button to turn the set ON.

2.

Press two buttons of  x  and  Z  simultaneously for five seconds.

3.

The message “LOCKED” is displayed and the tray is locked.
(Even if exiting from this mode, the tray is still locked.)

4.

Press two buttons of  x  and  Z  simultaneously for five seconds
again.

5.

The message “UNLOCKED” is displayed and the tray is
unlocked.

6.

To exit from this mode, press the  ?/1  button to turn the set
OFF.

• All fluorecent segments and LEDs are tested.
• Keyboard check.

Procedure:
1. Press  ?/1  button to turn the set ON.
2. To enter the test mode, press the three buttons  x ,  PLAY

MODE/TUNING MODE  and  ENTER  simultaneously.

3. All segments and LEDs (without STANDBY LED) are turned

on.

4. Press  X  and  ENTER  buttons simultaneously, and the key

check mode is activated.

5. The message “KEY 0 0 0 ” is displayed.

Each time a button is pressed, the key code number is displayed.

6. Press  X  and  ENTER  buttons simultaneously, and the key

count mode is activated.

7. The message “KEYCNT 0” is displayed.

Each time a button is pressed, “KEYCNT 0” value increased.
However, once a button is pressed, it is no longer taken into
account.

8. Press  X  and  ENTER  buttons simultaneously, and the head

phone detect mode is activated.

9. The message “H_P OFF” is displayed when a headphone jack

is not inserted.
“H_P ON ” is displayed when a headphone jack is inserted.

10. Press  X  and  ENTER  buttons simultaneously, and the volume

control detect mode is activated.

11. The message “VOLUME FLAT” is displayed.

“VOLUME UP” is displayed if rotating  MASTER VOLUME
knob clockwise, or “VOLUME DOWN” is displayed if rotating
counterclockwise.

12. To exit from the GC test mode after the head phone detect mode,

press  X  and  ENTER  buttons simultaneously.

• The version or destination is displayed.

Procedure:
1. Press  ?/1  button to turn the set ON.
2. To enter the test mode, press the three buttons  x ,  PLAY

MODE/TUNING MODE  and  DISC 2  simultaneously.

3. The destination is displayed.
4. Press  DISPLAY  buttons simultaneously.
5. The version is displayed.
6. To exit from this mode, press  ?/1  button to turn the set OFF.

• This mode can run the CD sled motor freely. Use this mode, for

instance, when cleaning the pick-up.

Procedure:
1. Press ?/1 button to turn the set ON.
2. Select the function “CD”.
3. To enter the test mode, press three buttons x ,  PLAY MODE/

TUNING MODE  , and  Z  simultaneously.

4. The CD service mode is selected.
5. With the CD in stop status, press   M

 

  button  to move the

pick-up to outside track, or press  m

 

 button to inside track.

6. To exit from this mode, perform as follows:

1) Move the pick-up to the most inside track.
2) Press  ?/1  button to turn the set OFF.

 • Always move the pick-up to most inside track when exiting from

this mode.  Otherwise, a disc will not be unloaded.

• Do not run the sled motor excessively, otherwise the gear can be

chipped.