DOWNLOAD Sony HCD-GNZ77D / HCD-GNZ88D / MHC-GNZ77D / MHC-GNZ88D Service Manual ↓ Size: 10.98 MB | Pages: 116 in PDF or view online for FREE

17

5

Remove the two solders of motor.

4

MOTOR (TB) board

2

stopper

2

stopper

6

table motor assy (M741)

table assy

3

two screws

     (+BTTP (M2.6))

1

4

Remove the two solders of motor.

3

MOTOR (LD) board

1

belt (loading)

5

loading motor assy (M751)

2

two screws

     (+BTTP (M2.6))

18

2

two insulator screws

4

two insulators

5

two insulators

3

two insulator screws

6

pick-up unit

7

holder (310)

1

floating screw

     (+PTPWH M2.6)

6

DRIVER board

2

SW board

3

CN704 (2P)

4

CN703 (4P)

7

CN702 (5 core)

5

two screws

     (+BTTP (M2.6))

1

 screw

     (+BTTP (M2.6))

19

• This mode is used to check the fluorescent indicator tube, LEDs,

keys, VOLUME jog, model, destination, software version and
VACS level.

Procedure:
1. Press  

x

  button, [ILLUMINATION] button and [DISC 2] button

simultaneously.

2. All LEDs and segments in fluorescent indicator tube are lighted

up. All LEDs are lighted up in red color where the SUB
WOOFER ON/OFF LED is lighted up in green color.

3. When you want to enter to the software version dispaly mode,

press [DISC 1] button. The model information appears on the
fluorescent indicator tube. Press [DISC 1] button again to view
the destination information.

4. Each time [DISC 1] button is pressed, the display changes from

MC version, SYS version, UI version, DVD version, CDMA
version, CDMB version, ST version, TA version, TM version,
TC version in this order, and returns to the model version display.

5. When [DISC 3] button is pressed while the version numbers are

being displayed except model and destination, the date of the
software creation appears. When [DISC 3] button is pressed
again, the display returns to the software version display. When
[DISC 1] button is pressed while the date of the software creation
is being displayed, the date of the software creation is displayed
in the same order of software version display.

6. Press [DISC 2] button, the key check mode is activated.
7. In the key check mode, the fluorescent indicator tube displays

“K 0 V0”.
Turn the [OPERATIONAL DIAL] clockwise; “K” value increases
by one. Turn the [OPERATIONAL DIAL] counterclockwise; “K”
value increases by one. Each time a button is pressed, “K” value
increases. Press other keys on main unit to check whether the
key is detected. However, once a button has been pressed, it is
no longer taken into account.
“V” value increases in the manner of 0, 1, 2, 3 ... if [VOLUME]
knob is turned clockwise, or it decreases in the manner of 0, 9,
8, 7 ... if [VOLUME] knob is turned counterclockwise.

8. When [DISC 3] button is pressed after all LEDs and segments in

fluorescent indicator tube light up, the fluorescent indicator tube
displays “VACS A”. A is VACS level which is triggered by signal
level.

9. When [DISC SKIP/EX-CHANGE] button is pressed after all LEDs

and segments in fluorescent indicator tube light up, alternate
segments in fluorescent indicator tube would light up. If you
press [DISC SKIP/EX-CHANGE] button again, another half of
alternate segments in fluorescent indicator tube would light up.
When [DISC SKIP/EX-CHANGE] button is pressed again, all
segments lights off. Press [DISC SKIP/EX-CHANGE] button again
would cause all segments lights up.

10. To  release from this mode, press three buttons in the same

manner as step 1, or disconnect the power cord.

• This mode is used to check operations of the respective sections

of Amplifier and Tape.

• To enter Common Test Mode

1. Press  

x

  button, [ILLUMINATION] button and [DISC 3] button

simultaneously.

2. The DVD ring indicators and the line below DVD ring indicator

flash synchronously on the fluorescent indicator tube. The
function is changed to TV where the function is changed to
DVD.

• Check of Amplifier

1. Press [EQ BAND/MEMORY] button repeatedly until a message

“GEQ MAX” appears on the fluorescent indicator tube. GEQ
increases to its maximum.

2. Press [EQ BAND/MEMORY] button repeatedly until a message

“GEQ MIN” appears on the fluorescent indicator tube. GEQ
decreases to its minimum.

3. Press [EQ BAND/MEMORY] button repeatedly until a message

“GEQ FLAT” appears on the fluorescent indicator tube. GEQ
is set to flat.

4. When the [VOLUME]  knob is turned clockwise even slightly,

the sound volume increases to its maximum and a message
“VOLUME MAX” appears on the fluorescent indicator tube.

5. When the [VOLUME]  knob is turned counterclockwise even

slightly, the sound volume decreases to its minimum and a
message “VOLUME MIN” appears on the fluorescent indicator
tube.

• Tape function

1. When a tape is inserted in Deck B and recording is started, the

function is changed to TV automatically. The function is change
to DVD automatically when a tape is inserted in Deck B and
recording is started. When [CD SYNC] button is pressed during
recording in function, ALC (Automatic Logic Control) is turned
on.

2. During recording, press  

m

  button will stop the recording and

the function is changed to TAPE B and rewind the tape in Deck
B until the recording start position and playback of the tape in
Deck B is started. If the [REC PAUSE/START] button is pressed
for a pause and pressed again to resume recording during
recording time, when the tape is rewind, the tape will be rewind
until the position where the pause is applied.

• To release from Common Test mode

1. To release from this mode, press  

?

/

1

  button.

2. The cold reset is enforced at the same time.

• The cold reset clears all data including preset data stored in the

RAM to initial conditions. Execute this mode when returning
the set to the customer.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press  

x

    button,  [ILLUMINATION]  button, and  

?

/

1

    button

simultaneously.

3. The message “COLD RESET” appears on the fluorescent

indicator tube. Then, the fluorescent indicator tube becomes
blank for a while, and the system is reset.

• This mode is used to switch on and off the VACS (Variable

Attenuation Control System).

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press  

x 

 button, [DIRECTION] button and [DISC 1]

simultaneously. The message “VACS OFF” or “VACS ON”
appears on the fluorescent indicator tube.

• The step interval of AM channels can be toggled between 9 kHz

and 10 kHz. This mode is not available for Saudi Arabia and
Russia models.

20

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press [TUNER/BAND] button repeatedly to select the “AM”.
3. Press  

?

/

1

  button to turn off the system.

4. Press [ILLUMINATION] button and  

?

/

1

  button simultaneously.

The system will turn on automatically. The message “AM 9K
STEP” or “AM 10K STEP” appears on the fluorescent indicator
tube and thus the channel step is changed.

• This mode moves the optical pick-up to the position durable to

vibration and clears all data including preset data stored in the
RAM to initial conditions. Use this mode when returning the
set to the customer after repair.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Select DVD function.
3. Press  

x

  button, [DIRECTION] button and  

?

/

1

  button

simultaneously during “DVD NO DISC” condition. The system
will turn off automatically.

4. After the “STANDBY” blinking display finishes, a message

“MECHA LOCK” appears on the fluorescent indicator tube and
the DVD ship mode is set.

• This mode moves the optical pick-up to the position durable to

vibration. Use this mode when returning the set to the customer
after repair.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Select DVD function.
3. Press [DVD] button and  

?

/

1

  button simultaneously during “DVD

NO DISC” condition. The system will turn off automatically.

4. After the “STANDBY” blinking display finishes, a message

“MECHA LOCK” appears on the fluorescent indicator tube and
the DVD ship mode is set.

• This mode let you lock the disc tray. When this mode is

activated, the disc tray will not open when [OPEN/CLOSE]
button or [DISC SKIP/EX-CHANGE] button is pressed. The
message “LOCKED” will appears on the fluorescent indicator
tube.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Select DVD function.
3. Press  

x

  button and [OPEN/CLOSE] button simultaneously and

hold down until “LOCKED” or “UNLOCKED” appears on the
fluorescent indicator tube (around 5 seconds).

• This mode prevents the system from turning off automatically

when TCM is not connected. Therefore, measurements can be
done even when TCM is not connected during production.

Procedure:
1. When the system is turned off, press [EQ BAND/MEMORY]

button, [TAPE A/B] button and  

?

/

1

  button simultaneously. The

system will turn on automatically.

2. The message “TCM OFFLINE” will appears on the fluorescent

indicator tube.

• To release from TCM Offline Mode

To release from this mode, perform “COLD RESET” or turn off
the power supply.

• This mode let you switch from TV to SAT and vice-versa.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Select TV function.
3. Press  [TV/SAT]  button and  

?

/

1

    button simultaneously. The

function will change to SAT. Press the same buttons again to
change from SAT to TV.

• This mode let you change the color system of the video output

from PAL to NTSC or vice-versa. This mode is not available for
Latin American and Russian models.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Select DVD function.
3. Press  

?

/

1

  button again to turn off the system.

4. Press  

X

  button and  

?

/

1

  button simultaneously. The system

will turn on automatically.
The message “COLOR PAL” or “COLOR NTSC” appears on
the fluorescent indicator tube.

• This mode let you disable the remote commander reception.

When this mode is activated, the system will not response if the
button on the remote commander is pressed. The message “RM
DISABLE” appears on the fluorescent indicator tube.
This mode is essential for conducting test and repairing when
no interruption from the other remote commander is expected.
This mode is cancelled automatically when the system is turned
off.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press  

x

  button, [DIRECTION] button and [DISC 3] button

simultaneously until “SIRCS ON” or “SIRCS OFF” appears on
the fluorescent indicator tube.

• This mode let you change the format of the video output from

the COMPONENT OUT jacks among PROGRESSIVE AUTO,
PROGRESSIVE VIDEO and INTERLACE.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press [DVD] button and [DISPLAY] button simultaneously. “P

AUTO” or “P VIDEO” or “INTERLACE” appears on the
fluorescent indicator tube.

• This mode is used to display the MTK firmware version.

Procedure:
1. Press  

?

/

1

  button to turn on the system.

2. Press [DVD] button to switch to DVD function.
3. Press  

?

/

1

  button again to turn off the system.

4. Press  

x

    button and  

?

/

1

    button. The system turns on

automatically.

5. The version of MTK firmware appears on the TV screen.

• This mode let you make diagnosis and adjustment easily by

using the remote commander and the TV. The instructions,
diagnostic results, etc. are given on the on-screen display.