DOWNLOAD Sony HCD-GNV111D / HCD-GNV99D / MHC-GNV111D / MHC-GNV99D Service Manual ↓ Size: 9.95 MB | Pages: 100 in PDF or view online for FREE

25

5. Wait until a hexadecimal number appear.

Manual Adjust

1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. ED:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:

Change Value
[0] Return to previous menu

6. Convert data from hexadecimal to decimal using conversion

table.

7. Press [RETURN] to return back to previous menu.

8. Press [0] to return to Top Menu and power OFF the DVD Player.

Information of Emergency History.

1. In standby mode, press [TOP MENU], [CLEAR], 

?/1

 buttons to

enter Remocon Diagnosis Mode.

2. Select “3. Emergency History”.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next] Next Page [Prev] Prev Page

3. Laser Hours

DVD Laser ON time. (Total ON time)
CD Laser ON time. (Total ON time)

4. Emergency History

The history information from last “1” to “10” can be
scrolled with [NEXT] button or [PREV] button.

5. Error code

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

6. Error code list

01: Communication error (No reply from syscon)
02: Syscon hung up
03: Power OFF request when syscon hung up
19: Thermal shutdown
24: MoveSledHome error
25: Mecha move error (5 Changer)
26: Mecha move stack error
30: DC Motor adjustment error
31: DPD offset adjustment error
32: TE Balance adjustment error
33. TE Sensor adjustment error
34. TE loop gain adjustment error
35. FE loop gain adjustment error
36. Bad jitter after adjustment
40. Focus NG
42. Focus Layer Jump NG
52. Open kick spindle error
51: Spindle stop error
60: Focus on error
61: Seek fail error
62: read Qdata/ID error
70: Lead In Data Read Fail
71: TOC read time out (CD)
80: Can’t Buffering
81: Unknown media type

7. Error code parameters

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

This is the detailed contents od error information

8. Laser hours at error happend.

Example of Error code

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

This is Laser hours when an error happaned.

9. How to Clearing laser hours

Press [DISPLAY], [CLEAR] buttons in this order.
Both CD and DVD data are cleared.

Emg. History Check

Laser Hours

CD

0h

0min

DVD

0h

0min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next] Next Page [Prev] Prev Page
[0] Return to Top Menuas

26

10. How to Clearing Emergency code

Press [TOPMENU], [CLEAR] buttons in this order.
All emergency code are cleared.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 00 00 00 00

00 00 00 00

00 00 00 00

00 00 00 00

2. 00 00 00 00

00 00 00 00

00 00 00 00

00 00 00 00

[Next] Next Page [Prev] Prev Page

11. Press [0] button, return to TOP MENU.

How to initializing setup data.

1. In standby mode, press [TOP MENU], [CLEAR], 

?/1

  buttons

to enter Remocon Diagnosis Mode.

2. Select “3. Emergency History”.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next] Next Page [Prev] Prev Page

3. Initializing setup data

Press [MENU], [CLEAR] buttons in this order.
The data have been initialized when “Initialize setup data...”
mesage is displayed.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

Initialize setup data ...

[Next] Next Page [Prev] Prev Page

4. The Emergency history display screen will be restored soon.

Emg. History Check

Laser Hours

CD

999h

59min

DVD

999h

59min

1. 01 05 04 04

00 92 46 00

00 00 00 00

00 00 23 45

2. 02 02 01 01

00 A9 4B 00

00 00 00 00

00 00 23 45

[Next] Next Page [Prev] Prev Page

5. Press [0] button, return to TOP MENU.

Information of firmware version.

1. In standby mode, press [TOP MENU],  [CLEAR],  [POWER]

buttons to enter Remocon Diagnosis Mode.

2. Select “4. Version Information”.

Version information

Firm (Main) : Ver. xxxxx
Firm (Sub) : xxxxx
RISC : xxxxx
8032 : xxxxx
Audio DSP : xxxxx
Servo DSP : xxxxx

[0] Return to Top Menu

3. Press [0] button, return to TOP MENU.

27

1. Clean the following parts with a denatured alcohol-moistened

swab:
record/playback heads pinch rollers
erase head

rubber belts

capstan

idlers

2. Demagnetize the record/playback head with a head

demagnetizer.

3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to

the parts adjusted.

5. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

3.06 N • m to 6.96 N • m

FWD

CQ-102C

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

FWD

0.19 N • m to 0.58 N • m

back tension

CQ-102C

2 to 6 g • cm

(0.02 – 0.08 oz • inch)

 3.06 N • m to 6.96 N • m

REV

CQ-102RC

31 to 71 g • cm

(0.43 – 0.98 oz • inch)

0.19 N • m to 0.58 N • m

REV

CQ-102RC

2 to 6 g • cm

back tension

(0.02 – 0.08 oz • inch)

6.96 N • m to 14.02 N • m

FF/REW

CQ-201B

71 to 143 g • cm

(0.98 – 1.99 oz • inch)

9.80 N • m

FWD tension

CQ-403A

100 g or more

(3.53 oz or more)

9.80 N • m

REV tension

CQ-403R

100 g or more

(3.53 oz or more)

Mode

Torque meter

Meter reading

0 dB=0.775 V

1. Demagnetize the record/playback head with a head

demagnetizer.

2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the

parts adjust.

4. The adjustments should be performed with the rated power

supply voltage unless otherwise noted.

5. The adjustments should be performed in the order given in

this service manual.  (As a general rule, playback circuit
adjustment should be completed before performing recording
circuit adjustment.)

6. The adjustments should be performed for both L-CH and R-

CH.

7. Switches and controls should be set as follows unless otherwise

specified.

• Test Tape

Note:  Perform this adjustments for both decks

1. Mode:  Playback

P-4-A100

10 kHz, –10 dB

Azimuth Adjustment

set

MAIN board
CN510
Pin 

1

 (L-CH)

Pin 

3

 (R-CH)

MAIN board
CN510
Pin 

2

 (GND)

+
–

level meter

test tape
P-4-A100
(10 kHz, –10 dB)

2. Turn the adjustment screw and check output peaks. If the peaks

do not match for L-CH and R-CH, turn the adjustment screw
so that outputs match within 1dB of peak.

Screw
position

L-CH
peak

within
1dB

Output
level

L-CH
peak

R-CH
peak

within
1dB

Screw
position

R-CH
peak

28

[TEST DISC LIST]
Use the following test disc on test mode.
• CD:

YEDS-18 (PART No. 3-702-101-01)

or

PATD-012 (PART No. 4-225-203-01)

• DVD (SL)
   NTSC

HLX-503 (PART No. J-6090-069-A)

or

HLX-504 (PART No. J-6090-088-A)

   PAL

HLX-506 (PART No. J-6090-077-A)

• DVD (DL)
   NTSC

HLX-501 (PART No. J-6090-071-A)

or

HLX-505 (PART No. J-6090-089-A)

   PAL

HLX-507 (PART No. J-6090-078-A)

1. Connect an oscilloscope to CN105 pin 6  (RFMON) and

CN105 pin 3 (GND) on the DMB10 board.

2. Turn the power on.
3. Set the test disc (DVD: HLX-503 (NTSC) or HLX-504 (PAL),

CD: YEDS-18) on the tray and press  H  button to playback.

4. Confirm that oscilloscope waveform is clear and check

RFMON signal level is correct or not.

A clear RFMON signal waveform means that the shape “

◊” can be

clearly distinguished at the center of the waveform.

Checking Location: DMB10 board (Side A)

+
–

CN105 pin 

6

 (RFMON)

CN105 pin 

3

 (GND)

oscilloscope 

DMB10 board

VOLT/DIV: 200 mV

TIME/DIV: 500 ns

RFMON signal waveform

level: 0.58 to 1.23 Vp-p (DVDSL)

          0.57 to 1.1 Vp-p (CD)

IC102

IC101

IC104

IC201

CN105

CN106

CN105 pin 

3

 (GND)

CN105 pin 

6

 (RFMON)

1

6

3. Mode:  Playback

4. After the adjustments, apply suitable locking compound to

the pats adjusted.

Adjustment Location:  Playback Head (Deck A).

Record/Playback/Erase Head (Deck B).

MAIN
board
CN510
set

test tape
P-4-A100
(10 kHz, –10 dB)

pin 

3

oscilloscope

L-CH

R-CH

V

H

waveform of oscilloscope

in phase 45

°

90

°

135

°

180

°

good

wrong

pin 

2

pin 

1

L

R

forward

reverse

Do not use exiting test disc for DVD.

Confirmation of mirror time adjustment and IOP adjustment
(Refer to page 24 of the TEST MODE)
• Execute this adjustment when exchange the BASE UNIT.