Sony HT-DDW980 / STR-K980 Service Manual ▷ View online
SERVICE MANUAL
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
E Model
MULTI CHANNEL AV RECEIVER
9-887-239-01
2006E1678-1
© 2006.05
© 2006.05
Ver. 1.0 2006.05
SPECIFICATIONS
STR-K980
• STR-K980 is the tuner and the amplifier
section in HT-DDW980.
Manufactured under license from Dolby Laboratories.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
“Dolby”, “Pro Logic” and the double-D symbol are trademarks of
Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of
Digital Theater Systems, Inc.
— Continued on next page —
Amplifier section
Power Output
1)
6 ohms 1 kHz, THD 0.7 %
FRONT
2)
: 110
W/ch
CENTER
2)
: 110 W
SUR
2)
: 110
W/ch
Music power output
FRONT
2)
: 140
W/ch
CENTER
2)
: 140 W
SUR
2)
: 140 W/ch
1) Measured under the following conditions:
2) Depending on the sound field settings and the source,
there may be no sound output.
Inputs (Analog)
Inputs (Digital)
Outputs (Analog)
Reproduction frequency range:
28 – 20,000 Hz
Tone
SA-CD/CD,
MD/TAPE, DVD,
VIDEO 1, 2, 3
MD/TAPE, DVD,
VIDEO 1, 2, 3
Sensitivity: 800 mV
Impedance: 50 kohms
Impedance: 50 kohms
DVD (Coaxial)
Sensitivity: –
Impedance: 75 ohms
Impedance: 75 ohms
VIDEO 1, 2
(Optical)
(Optical)
Sensitivity: –
Impedance: –
Impedance: –
MD/TAPE (OUT),
VIDEO 1 (AUDIO
OUT)
VIDEO 1 (AUDIO
OUT)
Voltage: 800 mV
Impedance: 10 kohms
Impedance: 10 kohms
SUB WOOFER
Voltage: 2 V
Impedance: 1 kohm
Impedance: 1 kohm
Gain levels
±6 dB, 1 dB step
FM tuner section
Tuning range
87.5 - 108.0 MHz
Antenna
FM wire antenna
Antenna terminals
75 ohms, unbalanced
Intermediate frequency
10.7 MHz
With 10-kHz tuning scale:
530 – 1,610 kHz
Antenna
Loop antenna
Intermediate frequency
450 kHz
Video section
Inputs/Outputs
Video:
1 Vp-p, 75 ohms
COMPONENT VIDEO:
Y: 1 Vp-p, 75 ohms
P
B
/C
B
/B-Y: 0.7 Vp-p,
75 ohms
P
R
/C
R
/R-Y: 0.7 Vp-p,
75 ohms
80 MHz HD Pass Through
AM tuner section
Tuning range
Area code
Power requirements
MX
127 V AC, 60 Hz
2
STR-K980
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350
°C.
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
also be added to ordinary solder.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK
0
OR DOTTED LINE
WITH MARK
0
ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
General
Power consumption 190 W
Power consumption (during standby mode)
0.2 W
Dimensions (w/h/d) (Approx.)
430
157.5 316 mm
including projecting parts
and controls
and controls
Mass (Approx.)
8.0 kg
×
×
Design and specifications are subject to
change without notice.
change without notice.
Power requirements
Area code
Power requirements
MX
127 V AC, 60 Hz
CENTER
SURROUND
FRONT
R
R
L
L
+
–
+
–
SPEAKERS
SPEAKERS
+
–
About area codes
The area code of the receiver you purchased is
shown on the lower right portion of the rear panel
(see the illustration below).
shown on the lower right portion of the rear panel
(see the illustration below).
Any differences in operation, according to the area
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
code, are clearly indicated in the text, for example,
“Models of area code AA only”.
Area code
• Abbreviation
MX
: Mexican model
3
STR-K980
TABLE OF CONTENTS
1.
GENERAL
...................................................................
4
2.
TEST MODE
............................................................... 13
3.
DIAGRAMS
3-1.
Block Diagram – MAIN Section – .................................. 16
3-2.
Block Diagram – DISPLAY/POWER Section – ............. 17
3-3.
Printed Wiring Board – DIGITAL Board (Side A) – ...... 18
3-4.
Printed Wiring Board – DIGITAL Board (Side B) – ...... 19
3-5.
Schematic Diagram – DIGITAL Board (1/5) – .............. 20
3-6.
Schematic Diagram – DIGITAL Board (2/5) – .............. 21
3-7.
Schematic Diagram – DIGITAL Board (3/5) – .............. 22
3-8.
Schematic Diagram – DIGITAL Board (4/5) – .............. 23
3-9.
Schematic Diagram – DIGITAL Board (5/5) – .............. 24
3-10. Printed Wiring Board – MAIN Board – ......................... 25
3-11. Schematic Diagram – MAIN Board (1/3) – ................... 26
3-12. Schematic Diagram – MAIN Board (2/3) – ................... 27
3-13. Schematic Diagram – MAIN Board (3/3) – ................... 28
3-14. Printed Wiring Boards
3-11. Schematic Diagram – MAIN Board (1/3) – ................... 26
3-12. Schematic Diagram – MAIN Board (2/3) – ................... 27
3-13. Schematic Diagram – MAIN Board (3/3) – ................... 28
3-14. Printed Wiring Boards
– DISPLAY Board, POWER Board – ............................. 29
3-15. Schematic Diagram
– DISPLAY Board, POWER Board – ............................. 30
3-16. Printed Wiring Board – STANDBY Board – ................. 31
3-17. Printed Wiring Board – SPEAKER C/SB Board – ........ 32
3-18. Schematic Diagram
3-17. Printed Wiring Board – SPEAKER C/SB Board – ........ 32
3-18. Schematic Diagram
– SPEAKER C/SB Board, STANDBY Board – ............. 33
3-19. Printed Wiring Boards – ADCC Board, VIDEO 3 Board,
SPEAKER B Board – ...................................................... 35
3-20. Schematic Diagram – ADCC Board, VIDEO 3 Board,
SPEAKER B Board – ...................................................... 35
3-21. Printed Wiring Boards
– VIDEO Board, HEADPHONE Board – ....................... 36
3-22. Schematic Diagram
– VIDEO Board, HEADPHONE Board – ....................... 37
4.
EXPLODED VIEWS
4-1.
Front Panel Section ......................................................... 45
4-2.
Chassis Section ................................................................ 46
5.
ELECTRICAL PARTS LIST
.................................. 47
4
STR-K980
SECTION 1
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Panel frontal
Para extraer la cubierta
Pulse PUSH.
Cuando extraiga la cubierta, manténgala fuera
del alcance de los niños.
Cuando extraiga la cubierta, manténgala fuera
del alcance de los niños.
Receptor
?/1
AUTO CAL MIC
PHONES
VIDEO 3 IN/PORTABLE AV IN
VIDEO
L AUDIO R
MEMORY/
ENTER
TUNING
MODE
TUNING
2CH
A.F.D.
MOVIE
MUSIC
MODE
X-ROUND
SPEED
DISPLAY
INPUT MODE
INPUT SELECTOR
MASTER VOLUME
SPEAKERS
(ON/OFF)
1
3
2
5
7
6
4
8
9
0
qa
qk
qs
qd
qf
qg
qh
PUSH
qj
Nombre
Función
A ?
/
1
Púlselo para encender o
apagar el receptor.
apagar el receptor.
B
SPEAKERS
(ON/OFF)
Púlselo para encender y
apagar los altavoces y el
altavoz potenciador de
graves.
apagar los altavoces y el
altavoz potenciador de
graves.
C
Pantalla
En la pantalla aparece el
estado actual del dispositivo
seleccionado o de una lista
de elementos seleccionables.
estado actual del dispositivo
seleccionado o de una lista
de elementos seleccionables.
D
Sensor de
mando a
distancia
Recibe señales del mando a
distancia.
distancia.
E
DISPLAY
Púlselo para seleccionar la
información que se muestra
en la pantalla.
información que se muestra
en la pantalla.
F
INPUT MODE
Púlselo para seleccionar el
modo de entrada cuando los
mismos dispositivos están
conectados a las tomas
digital y analógica.
modo de entrada cuando los
mismos dispositivos están
conectados a las tomas
digital y analógica.
G
MASTER
VOLUME
VOLUME
Gírelo para ajustar el nivel
de volumen de todos los
altavoces al mismo tiempo.
de volumen de todos los
altavoces al mismo tiempo.
H
X-ROUND
SPEED
Púlselo para ajustar la
velocidad del efecto
velocidad del efecto
X-ROUND.
X-ROUND
MODE
MODE
Púlselo para seleccionar el
modo X-ROUND.
modo X-ROUND.
I
INPUT
SELECTOR
SELECTOR
Gírelo para seleccionar la
fuente de entrada que desea
reproducir.
fuente de entrada que desea
reproducir.
J
MOVIE,
MUSIC
Púlselo para seleccionar
campos de sonido (MOVIE,
MUSIC).
campos de sonido (MOVIE,
MUSIC).
K
A.F.D.
Púlselo para seleccionar el
modo A.F.D..
modo A.F.D..
L
2CH
Púlselo para seleccionar el
modo 2CH STEREO.
modo 2CH STEREO.
M
TUNING +/–
Púlselo para buscar una
emisora.
emisora.
N
TUNING MODE
Púlselo para seleccionar el
modo de sintonización.
modo de sintonización.
O
MEMORY/
ENTER
ENTER
Púlselo para almacenar una
emisora o introducir la
selección cuando seleccione
los ajustes.
emisora o introducir la
selección cuando seleccione
los ajustes.
Nombre
Función
P
Tomas VIDEO 3
IN/PORTABLE
AV IN
IN/PORTABLE
AV IN
Para conectar una
videocámara o una consola
de videojuegos.
videocámara o una consola
de videojuegos.
Q
Toma AUTO
CAL MIC
CAL MIC
Permite realizar la conexión
con el micrófono
optimizador ECM-AC2
suministrado para efectuar
la función de calibración
automática.
con el micrófono
optimizador ECM-AC2
suministrado para efectuar
la función de calibración
automática.
R
Toma PHONES
Permite conectar unos
auriculares.
auriculares.