Sony HCD-DX60AV / HCD-RG70AV / MHC-DX60AV / MHC-RG70AV Service Manual ▷ View online
HCD-DX60AV/RG70AV
11
2-6.
TAPE MECHANISM DECK
2-7.
BACK PANEL SECTION
3
Tape mechanism deck
1
five screws
(+BVTP 2.6
×
8)
1
screw
(+BVTP 2.6
×
8)
2
harness
3
seven screws
(+BVTP 3
×
10)
1
connector (CN506)
1
connector (CN901)
1
connector (CN2)
4
two screws
(+BVTP 3
×
10)
5
back panel section
2
connector
(CN408)
HCD-DX60AV/RG70AV
12
qs
0
two screws (+PTPWH M2.6)
2
screw (+PTPWH M2.6)
qa
screws (DIA. 12)
8
two screws (M2.6)
7
BD board
6
Remove four solders.
qd
two insulators
3
holder BU assy
qd
two insulators
9
two stoppers (BU)
5
screw (M2.6)
4
wire (flat type)
(16 core)
(16 core)
qf
base unit
(BU-K6BD38)
(BU-K6BD38)
1
wire (flat type)
(19 core)
(19 core)
(CN101)
2-8.
MAIN BOARD
2-9.
BASE UNIT (BU-K6BD38)
1
two screws (+BVTP 3
×
10)
2
MAIN board
MAIN board
HCD-DX60AV/RG70AV
13
2-10. DRIVER BOARD, MOTOR BOARD, ADDRESS SENSOR BOARD
qa
Pull-out the table.
6
two
screws (BTTP M2.6)
qs
screw (+PTPWH 2.6
×
8)
qd
tray
1
screw (BTTP M2.6)
qf
screw (BTTP M2.6)
7
0
MOTOR board
qg
ADDRESS SENSOR board
4
driver board
2
5
Remove the two solderings of motor.
9
connector
3
wire (flat type)
(8 core)
(8 core)
(CN702)
8
wire (flat type)
(8 core)
(8 core)
(CN721)
14
HCD-DX60AV/RG70AV
SECTION 3
TEST MODE
[MC Cold Reset]
• The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning
the set to the customer.
the set to the customer.
Procedure:
1. Press three buttons
1. Press three buttons
x
,
ENTER
, and
I/1
simultaneously.
2. The fluorescent indicator tube displays “COLD RESET” and
the set is reset.
[CD Ship Mode]
• This mode moves the pickup to the position durable to vibra-
tion. Use this mode when returning the set to the customer after
repair.
repair.
Procedure:
1. Press
1. Press
I/1
button to turn the set ON.
2. Press
CD
button and
I/1
button simultaneously. (Until
“STANDBY” appears)
3. When you release the buttons, a message “LOCK” is displayed
on the fluorescent indicator tube, and the CD ship mode is set.
[MC Hot Reset]
• This mode resets the set with the preset data kept stored in the
memory. The hot reset mode functions same as if the power
cord is plugged in and out.
cord is plugged in and out.
Procedure:
1. Press three buttons
1. Press three buttons
x
,
ENTER
, and
DISPLAY
simultaneously.
2. The fluorescent indicator tube becomes blank instantaneously,
and the set is reset.
[CD Service Mode]
• This mode can run the CD sled motor freely. Use this mode, for
instance, when cleaning the pickup.
Procedure:
1. Press
1. Press
I/1
button to turn the set ON.
2. Select the function “CD”.
3. Press three buttons
3. Press three buttons
x
,
ENTER
, and
Z OPEN/CLOSE
simul-
taneously.
4. The CD service mode is selected.
5. With the CD in stop status, press and hold the
5. With the CD in stop status, press and hold the
>
button to
move the pickup to outside track, or press and hold
the
the
.
button to inside track.
6. To exit from this mode, perform as follows:
1) Move the pickup to the most inside track.
2) Press three buttons in the same manner as step 2.
2) Press three buttons in the same manner as step 2.
Note:
• Always move the pickup to most inside track when exiting from
this mode. Otherwise, a disc will not be unloaded.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[Change-over of AM Tuner Step between 9 kHz and
10 kHz]
10 kHz]
• A step of AM channels can be changed over between 9 kHz and
10 kHz.
Procedure:
1. Press
1. Press
I/1
button to turn the set ON.
2. Select the function “TUNER”, and press
TUNER/BAND
button to select the BAND “AM”.
3. Press
I/1
button to turn the set OFF.
4. Press
ENTER
and
I/1
buttons simultaneously, and the display
of fluorescent indicator tube changes to “AM 9 k STEP” or
“AM 10 k STEP”, and thus the channel step is changed over.
“AM 10 k STEP”, and thus the channel step is changed over.
[GC Test Mode]
• This mode is used to check the software version, fluorescent
indicator tube, LED, keyboard, headphone and volume.
Procedure:
1. Press three buttons
1. Press three buttons
x
,
ENTER
, and
DISC 2
simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3. When
3. When
ENTER
and
DISC 2
buttons are pressed simultaneously,
the key number check mode is activated. Key numbers of each
key series are displayed and the key check mode is activated.
key series are displayed and the key check mode is activated.
4. In the key check mode, the fluorescent indicator tube displays
“KEY 000”.
5. When
ENTER
and
DISC 2
buttons are pressed simultaneously,
the key count mode is activated. In this mode, the fluorescent
indicator tube displays “KEYCNT 00”. When each button is
pressed, the key series number increases first, then key value
increases next. However, once a button is pressed, key value is
no longer counted up with the same button.
indicator tube displays “KEYCNT 00”. When each button is
pressed, the key series number increases first, then key value
increases next. However, once a button is pressed, key value is
no longer counted up with the same button.
6. When
ENTER
and
DISC 2
buttons are pressed simultaneously,
the headphone check mode is activated. “H_P ON” is displayed
when headphones are connected, and “H_P OFF” is displayed
when no headphones are connected.
when headphones are connected, and “H_P OFF” is displayed
when no headphones are connected.
7. When
ENTER
and
DISC 2
buttons are pressed simultaneously,
the volume check mode is activated and “VOLUME FLAT” is
displayed on the fluorescent indicator tube. When you rotate
the volume knob in + direction, “VOLUME UP” is displayed,
and when you rote it in – direction, “VOLUME DOWN” is
displayed.
displayed on the fluorescent indicator tube. When you rotate
the volume knob in + direction, “VOLUME UP” is displayed,
and when you rote it in – direction, “VOLUME DOWN” is
displayed.
8. To exit this mode, press three buttons mentioned at step 1 in the
same manner, or press
ENTER
and
DISC 2
buttons
simultaneously at step 8.
Click on the first or last page to see other HCD-DX60AV / HCD-RG70AV / MHC-DX60AV / MHC-RG70AV service manuals if exist.