Sony HCD-DR7AV / HCD-XB800AV / LBT-DR7AVS Service Manual ▷ View online
– 13 –
AMS Test Mode
• This mode is used for checking the AMS operations of the tape deck.
JIG
7-819-039-12 Alignment tape, AMS-110A
7-819-039-12 Alignment tape, AMS-110A
Procedure:
1. Press the
1. Press the
1/u button to turn the set ON.
2. Set the tape (AMS-110A).
3. Press the three buttons
3. Press the three buttons
t/CLOCK SET , ENTER , and DISC 3 button simultaneously.
4. “TEST MODE” is displayed on the fluorescent display tube.
5. Press the FUNCTION button and switch the function to the deck with the tape (AMS-110A).
6. Press the CD SYNCHRO button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.
7. AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8.
5. Press the FUNCTION button and switch the function to the deck with the tape (AMS-110A).
6. Press the CD SYNCHRO button. “AMS CHECK” is displayed on the fluorescent display tube and the tape is rewound.
7. AMS starts in the normal direction. If the AMS count is 2 at shut down, proceed to step 8.
“NG” is displayed at other times, and the deck stops.
8. AMS starts in the opposite direction. If the AMS count is 2 at shut down again, “OK” is displayed.
“NG” is displayed at other times.
Aging Mode
During the aging mode, both the CD player and tape deck are executed together.
• If an error occurs:
Aging stops, and the error state is displayed on the fluorescent display tube.
• If no error occurs:
Aging is repeated.
• If an error occurs:
Aging stops, and the error state is displayed on the fluorescent display tube.
• If no error occurs:
Aging is repeated.
Procedure:
1. Press the
1. Press the
1/u button to turn the set ON.
2. Load 10 minute tapes with unbent rec-proof tabs in decks A and B.
3. Set CDs on the DISC 1 and DISC 4 tables.
4. Set the CD mode REPEAT to OFF and PLAY MODE to ALL DISCS.
3. Set CDs on the DISC 1 and DISC 4 tables.
4. Set the CD mode REPEAT to OFF and PLAY MODE to ALL DISCS.
(Press the PLAY MODE and REPEAT buttons to set these modes.)
5. Press the FUNCTION button to switch the function to “CD”.
6. Press the three buttons
6. Press the three buttons
t/CLOCK SET , ENTER , and DISC 4 button simultaneously.
7. Aging starts.
8. To end aging, press the
8. To end aging, press the
1/u button to turn the set OFF.
Aging Sequence:
Aging is performed in the following sequence.
Aging is performed in the following sequence.
• Tape Deck
1. The tape in deck A is rewound. “TAPE A AG-1” is displayed.
2. The FWD side of deck A is played for two minutes.
1. The tape in deck A is rewound. “TAPE A AG-1” is displayed.
2. The FWD side of deck A is played for two minutes.
“TAPE A AG-2” is displayed.
3. The tape in deck A is fast forwarded. “TAPE A AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.
4. The RVS side of deck A is played for two minutes.
4. The RVS side of deck A is played for two minutes.
“TAPE A AG-4” is displayed.
5. The tape in deck A is rewound. “TAPE A AG-5” is displayed.
6. The FWD side of deck B is played for two minutes.
6. The FWD side of deck B is played for two minutes.
“TAPE B AG-2” is displayed.
7. The tape in deck B is fast forwarded. “TAPE B AG-3” is displayed. Fast forward is carried out for 20 seconds or to the tape end.
8. The RVS side of deck B is played for two minutes.
8. The RVS side of deck B is played for two minutes.
“TAPE B AG-4” is displayed.
9. The tape in deck A is rewound. “TAPE A AG-5” is displayed.
10. Repeated from step 2.
10. Repeated from step 2.
• CD
1. The tray rotates.
2. DISC 1 is chucked.
3. The TOC is read.
4. The first track is played for 2 seconds.
5. The last track is played for 2 seconds.
6. The tray rotates.
7. DISC 4 is chucked.
8. The TOC is read.
9. The first track is played for 2 seconds.
10. The last track is played for 2 seconds.
11. Repeated from step 1.
1. The tray rotates.
2. DISC 1 is chucked.
3. The TOC is read.
4. The first track is played for 2 seconds.
5. The last track is played for 2 seconds.
6. The tray rotates.
7. DISC 4 is chucked.
8. The TOC is read.
9. The first track is played for 2 seconds.
10. The last track is played for 2 seconds.
11. Repeated from step 1.
– 14 –
• Display when ended abnormally
When the tape deck is abnormal:
When the tape deck is abnormal:
The state when ended abnormally is displayed.
The contents of display are the same as that during aging.
The contents of display are the same as that during aging.
When the CD player is abnormal:
A message indicating that errors such as “CD MEC ERR” have occurred.
Check the error contents in the following error history display mode.
Check the error contents in the following error history display mode.
Error History Display Mode
Mode which enables the history of error occurring in the CD player to be checked.
Execute this mode after ending the aging mode.
Execute this mode after ending the aging mode.
Procedure:
1. Press the
1. Press the
1/u button to turn the set ON.
2. Press the three buttons
t/CLOCK SET , ENTER , and CD SYNCHRO simultaneously.
3. A message such as “EMC@@EDC**” is displayed.
@@ : Number of mechanical errors (Up to three past errors)
**
**
: Number of errors (NO DISC ERROR) which occurs after chucking (Up to three past errors)
4. When checking the history of mechanical errors, press the PLAY MODE button. When checking errors after chucking, press the
REPEAT button to switch the display.
5. Press the
1/u button to end and turn the set OFF.
6. To erase the error history, perform COLD reset.
(Press the three buttons
t/CLOCK SET , ENTER , and DISC 1 simultaneously.
• Viewing the mechanical error history display
(Switch the history by pressing the PLAY MODE button.)
Display
E@@M#*****
E@@M#*****
@@ : Error number. 00 is the newest.
#
: Operating state of table
0
: Currently in the INITIAL mode
7
: Currently rotating to the right
8
: Currently rotating to the left
A
: Currently chucking down
B
: Currently chucking up
*
: Invalid
• Viewing the NO DISC ERROR history display
(Switch the history by pressing the REPEAT button.)
Display
E@@D##$$%*
E@@D##$$%*
@@ : Error number. 00 is the newest
##
: Error contents
01: Focus error
02: GFS error
03: Setup error
02: GFS error
03: Setup error
$$
: Retries
00: NO DISC is determined without attempting chucking
retry
02: NO DISC is determined after chucking retry.
%
: State when determined as NO DISC
1
: When stopped
2
: At setup
3
: At TOC READ
4
: When accessing
5
: When playing
6
: When pausing
7
: When manual searching (during play)
8
: When manual searching (during pausing)
*
: Invalid
– 15 –
Precaution
1. Clean the following parts with a denatured alcohol-moistened
swab:
record/playback heads
pinch rollers
erase head
rubber belts
capstan
idlers
2. Demagnetize the record/playback head with a head demagne-
tizer.
3. Do not use a magnetized screwdriver for the adjustments.
4. After the adjustments, apply suitable locking compound to the
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
5. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
Torque Measurement
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
31 to 71 g • cm
(0.43 – 0.98 oz • inch)
2 to 6 g • cm
(0.02 – 0.08 oz • inch)
71 to 143 g • cm
(0.98 – 1.99 oz • inch)
100 g or more
(3.53 oz or more)
100 g or more
(3.53 oz or more)
Record/Playback Head Azimuth Adjustment
(Deck A, Deck B)
(Deck A, Deck B)
Note: Perform this adjustments for both decks.
Procedure:
1. Mode : Playback
1. Mode : Playback
Signal
Used for
Tape
SECTION 5
MECHANICAL ADJUSTMENTS
Mode
FWD
Torque meter
CQ-102C
Meter reading
FWD
back tension
back tension
REV
REV
back tension
back tension
FF/REW
FWD tension
REV tension
CQ-102C
CQ-102RC
CQ-102RC
CQ-201B
CQ-403A
CQ-403R
SECTION 6
ELECTRICAL ADJUSTMENTS
DECK SECTION
0 dB=0.775V
1. Demagnetize the record/playback head with a head damagnetizer.
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
2. Do not use a magnetized screwdriver for the adjustments.
3. After the adjustments, apply suitable locking compound to the
parts adjusted.
4. The adjustments should be performed with the rated power sup-
ply voltage unless otherwise noted.
5. The adjustments should be performed in the order given in this
service manual. (As a general rule, playback circuit adjustment
should be completed before performing recording circuit adjust-
ment.)
should be completed before performing recording circuit adjust-
ment.)
6. The adjustments should be performed for both L-CH and R-CH.
7. Switches and controls should be set as follows unless otherwise
7. Switches and controls should be set as follows unless otherwise
specified.
P-4-A100
WS-48B
P-4-L300
10 kHz, –10 dB
3 kHz, 0 dB
315 Hz, 0 dB
Azimuth Adjustment
Tape Speed Adjustment
Level Adjustment
2. Turn the adjustment screw and check output peaks. If the peaks
do not match for L-CH and R-CH, turn the adjustment screw so
that outputs match within 1 dB of peak.
that outputs match within 1 dB of peak.
test tape
P-4-A100
(10kHz, –10dB)
P-4-A100
(10kHz, –10dB)
MD OUT
level meter
set
+
–
L-CH
peak
peak
R-CH
peak
peak
screw
position
position
output
level
level
within
1 dB
1 dB
L-CH
peak
peak
R-CH
peak
peak
screw
position
position
within 1dB
– 16 –
4. After the adjustments, apply suitable locking compound to the
parts adjusted.
Adjustment Location: Playback Head (Deck A)
Record/Playback/Erase Head (Deck B)
3. Mode: Playback
Tape Speed Adjustment (Deck A)
Note: Set the test mode using the following method and begin tape
speed adjustment.
In the test mode, the speed will switch to double speed or
normal speed each time the HI-SPEED DUB button is pressed.
In the test mode, the speed will switch to double speed or
normal speed each time the HI-SPEED DUB button is pressed.
Procedure:
With the power turned ON, press the
With the power turned ON, press the
t/CLOCK SET button,
ENTER button, and DISC 3 button simultaneously.
(The “VOLUME” on the fluorescent display tube will blink while
in the test mode.)
To exit the test mode, press the
(The “VOLUME” on the fluorescent display tube will blink while
in the test mode.)
To exit the test mode, press the
1/u button.
1. Insert the WS-48B into deck B.
2. Press the
2. Press the
· button of deck B.
3. Press the HI-SPEED DUB button and play the tape at double speed.
4. Adjust RV1001 of the LEAF SW board so that the reading of
4. Adjust RV1001 of the LEAF SW board so that the reading of
the frequency counter becomes 6000 ± 180 Hz.
5. Press the HI-SPEED DUB button and play the tape at normal speed.
6. Adjust RV1002 of the LEAF SW board so that the reading of
6. Adjust RV1002 of the LEAF SW board so that the reading of
the frequency counter becomes 3000 ± 90 Hz.
Adjustment Location: LEAF SW board
Sample Value of Wow and flutter
W.RMS (JIS) less than 0.3%
(test tape: WS-48B)
(test tape: WS-48B)
Playback Level Adjustment (Deck A, Deck B)
Procedure:
Mode: Playback
Mode: Playback
Deck A is RV311 (L-CH) and RV411 (R-CH), deck B is RV301
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.
(L-CH) and RV401 (R-CH)
so that adjustment within the following adjustment level.
Adjustment level:
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
CN301 playback level: 301.5 to 338.3 mV (–8.2 to –7.2 dB)
level difference between the channels: within ± 0.5 dB
Adjustment Location: AUDIO board
Adjustment Location
[LEAF SW BOARD]
[LEAF SW BOARD]
test tape
P-4-A100
(10kHz, –10dB)
P-4-A100
(10kHz, –10dB)
oscilloscope
set
Waveform of oscilloscope
in phase
45
°
90
°
135
°
180
°
good
wrong
MD OUT
Reverse
Foward
Remove the cassette lid.
test tape
P-4-L300
(315Hz, 0dB)
P-4-L300
(315Hz, 0dB)
level meter
set
MD OUT
RV1002
RV1001
RV1002(Normal Speed)
RV1001(High Speed)
Click on the first or last page to see other HCD-DR7AV / HCD-XB800AV / LBT-DR7AVS service manuals if exist.