Sony HCD-BX20I / HCD-BX50BTI Service Manual ▷ View online
HCD-BX20i/BX50BTi
5
HOW TO OPEN THE TRAY WHEN POWER SWITCH TURN OFF
Note: Please insert a screwdriver after removing the panel (side L).
About disassembly of the panel (side L), please refer to “3-2. Panel (Side L/R)” (page 13).
Open the tray.
Push the boss.
Insert the driver.
HCD-BX20i/BX50BTi
6
SECTION 2
GENERAL
This section is extracted
from instruction manual.
from instruction manual.
Basic Operations
This manual mainly explains operations using the
remote, but the same operations can also be performed
using the buttons on the unit having the same or similar
names.
remote, but the same operations can also be performed
using the buttons on the unit having the same or similar
names.
Before using the system
To use the remote
Slide and remove the battery compartment lid , and
insert the two supplied R6 (size AA) batteries,
insert the two supplied R6 (size AA) batteries,
side
first, matching the polarities shown below.
Notes on using the remote
With normal use, the batteries should last for about six months.
With normal use, the batteries should last for about six months.
Do not mix an old battery with a new one or mix different types of
batteries.
If you do not use the remote for a long period of time, remove the
batteries to avoid damage from battery leakage and corrosion.
To set the clock
Use buttons on the remote to set the clock.
1
Turn on the system.
Press
(power) .
2
Select the clock set mode.
Press TIMER MENU . If the current mode appears
on the display, press
on the display, press
/ repeatedly to select
“CLOCK SET?” and then press
(enter) .
3
Set the time.
Press
/ repeatedly to set the hour, and then
press
(enter) . Use the same procedure to set the
minutes.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.
To display the clock when the system is off, press
DISPLAY . The clock is displayed for about 8
seconds.
The clock settings are lost when you disconnect the
power cord or if a power failure occurs.
To display the clock when the system is off, press
DISPLAY . The clock is displayed for about 8
seconds.
To use the iPod
Insert an iPod Dock Adaptor into the unit’s connector
before use.
For details on the supplied iPod Dock Adaptors, refer to
the instructions supplied with the Dock Adaptors.
before use.
For details on the supplied iPod Dock Adaptors, refer to
the instructions supplied with the Dock Adaptors.
Adjusting the sound
To adjust the volume
Press VOLUME +/
(or VOL +/ on the unit) .
To add a sound effect
To
Press
Generate a more dynamic
sound (Dynamic Sound
Generator X-tra)
sound (Dynamic Sound
Generator X-tra)
DSGX on the unit.
Set the sound effect
EQ repeatedly to select
“BASS” or “TREBLE,” and
then press +/
“BASS” or “TREBLE,” and
then press +/
repeatedly
to adjust the level.
Playing a CD/MP3 disc
1
Select the CD function.
Press FUNCTION +/
(or FUNCTION on the unit)
repeatedly.
2
Place a disc.
Press
(open/close) on the unit, and place a disc
with the label side up on the disc tray.
To close the disc tray, press
(open/close) on the
unit.
Do not force the disc tray closed with your finger, as
this may damage the unit.
Do not force the disc tray closed with your finger, as
this may damage the unit.
3
Start playback.
Press
(play) (or CD (play/pause) on the
unit) .
To
Press
Pause playback
(pause) (or CD (play/
pause) on the unit) .
To resume play, press the button
again.
pause) on the unit) .
To resume play, press the button
again.
Stop playback
(stop) (or /CANCEL on the
unit) .
unit) .
Select a folder on an
MP3 disc
MP3 disc
+/
(select folder) .
Select a track or file
/ (go back/go forward)
.
Find a point in a
track or file
track or file
Hold down
/ (rewind/
fast forward) during playback,
and release the button at the
desired point.
and release the button at the
desired point.
Select Repeat Play
REPEAT repeatedly until
“REP” or “REP1” appears.
“REP” or “REP1” appears.
To change the play mode
Press PLAY MODE repeatedly while the player is
stopped. You can select normal play (“
stopped. You can select normal play (“
” for all MP3
files in the folder on the disc), shuffle play (“SHUF” or
“
“
SHUF*”), or program play (“PGM”).
* When playing a CD-DA disc,
(SHUF) Play performs the same
operation as normal (shuffle) play.
Notes on Repeat Play
All tracks or files on a disc are played repeatedly up to five times.
All tracks or files on a disc are played repeatedly up to five times.
“REP1” indicates that a single track or file is repeated until you stop
it.
Notes on playing MP3 discs
Do not save other types of tracks or files or unnecessary folders on a
Do not save other types of tracks or files or unnecessary folders on a
disc that has MP3 files.
Folders that have no MP3 files are skipped.
MP3 files are played back in the order that they are recorded onto
the disc.
The system can only play MP3 files that have a file extension of
“.MP3”.
If there are files on the disc that have the “.MP3” file extension,
but that are not MP3 files, the unit may produce noise or may
malfunction.
malfunction.
The maximum number of:
folders is 255 (including the root folder).
MP3 files is 511.
MP3 files and folders that can be contained on a single disc is 512.
folder levels (the tree structure of files) is 8.
MP3 files is 511.
MP3 files and folders that can be contained on a single disc is 512.
folder levels (the tree structure of files) is 8.
Compatibility with all MP3 encoding/writing software, recording
device, and recording media cannot be guaranteed. Incompatible
MP3 discs may produce noise or interrupted audio or may not play
at all.
MP3 discs may produce noise or interrupted audio or may not play
at all.
Notes on playing multisession discs
If the disc begins with a CD-DA (or MP3) session, it is recognized as
If the disc begins with a CD-DA (or MP3) session, it is recognized as
a CD-DA (or MP3) disc, and other sessions are not played back.
A disc with a mixed CD format is recognized as a CD-DA (audio)
disc.
Listening to the radio
1
Select “TUNER FM” or “TUNER AM.”
Press FUNCTION +/
(or FUNCTION on the unit)
repeatedly.
2
Select the tuning mode.
Press TUNING MODE repeatedly until “AUTO”
appears.
appears.
3
Tune in the desired station.
Press +/
(or TUNE +/ on the unit) . Scanning
stops automatically when a station is tuned in, and
then “TUNED” and “STEREO” (for stereo programs
only) appear.
then “TUNED” and “STEREO” (for stereo programs
only) appear.
To stop automatic scanning
Press
(stop) (or /CANCEL on the unit) .
To tune in a station with a weak signal
If “TUNED” does not appear and the scanning does not
stop, press TUNING MODE repeatedly until “AUTO”
and “PRESET” disappear, and then press +/
stop, press TUNING MODE repeatedly until “AUTO”
and “PRESET” disappear, and then press +/
(or TUNE
+/
on the unit) repeatedly to tune in the desired
station.
To reduce static noise on a weak FM stereo
station
station
Press FM MODE repeatedly until “MONO” appears
to turn off stereo reception.
to turn off stereo reception.
Playing the iPod
1
Select the iPod function.
Press FUNCTION +/
(or FUNCTION on the unit)
repeatedly.
2
Place the iPod.
3
Start playback.
Press
(play) (or iPod (play/pause) on the
unit) .
To control the iPod
You can control your iPod with the following buttons on
the remote or unit.
the remote or unit.
To
Press
Pause playback
(pause) (or iPod
(play/pause) on the unit) or
(play/pause) on the unit) or
(stop) .
Scroll up/down the
iPod menus
iPod menus
/ . You can scroll up or
down the iPod menus much like
the Click Wheel operations of
the iPod or the drag up-or-down
operations of the iPod touch.
down the iPod menus much like
the Click Wheel operations of
the iPod or the drag up-or-down
operations of the iPod touch.
Select a track
or chapter of
audiobook/podcast
or chapter of
audiobook/podcast
/ (go back/go forward)
. To fast-forward or fast-
rewind, hold down the button.
rewind, hold down the button.
Choose the selected
item
item
/
(enter) (or ENTER on
the unit) . You can choose the
selected item much like the center
button on the iPod or the touch
operation of the iPod touch.
selected item much like the center
button on the iPod or the touch
operation of the iPod touch.
Find a point in a
track or chapter of
audiobook/podcast
track or chapter of
audiobook/podcast
/ (fast rewind/fast
forward) during playback, and
release the button at the desired
point.
forward) during playback, and
release the button at the desired
point.
Return to the
previous menu or
select a menu
previous menu or
select a menu
/TOOL MENU /
(return) . You can return to the
previous menu or select a menu
much like the Menu button on
the iPod or the touch operation
of the iPod touch.
(return) . You can return to the
previous menu or select a menu
much like the Menu button on
the iPod or the touch operation
of the iPod touch.
To use the system as a battery charger
You can use the system as a battery charger for the iPod
when the system is both on and off.
The charging begins when the iPod is placed on the unit’s
connector . The charging status appears in the iPod
display. For details, see the user’s guide of your iPod.
when the system is both on and off.
The charging begins when the iPod is placed on the unit’s
connector . The charging status appears in the iPod
display. For details, see the user’s guide of your iPod.
To stop charging the iPod
Remove the iPod. If you stop charging the iPod when
the system is off, press DISPLAY until the clock
disappears in the display.
the system is off, press DISPLAY until the clock
disappears in the display.
Notes
When placing or removing the iPod, handle the iPod in the same
When placing or removing the iPod, handle the iPod in the same
angle as that of the iPod connector on the unit and do not twist
or sway the iPod to prevent connector damage.
or sway the iPod to prevent connector damage.
Do not carry the unit with an iPod set on the connector. Doing so
may cause a malfunction.
When placing or removing the iPod, brace the unit with one hand
and take care not to press the controls of the iPod by mistake.
To remove the iPod Dock Adaptor, pull it up with your fingernail or
a flat object using the slot inside the adaptor.
Before disconnecting the iPod, pause playback.
While playing video, you cannot use / . You can fast
rewind (fast forward) by holding down
/ .
To change the volume level, use VOLUME +/ (or VOL +/ on the
unit) . The volume level does not change even if adjusted on the
iPod.
iPod.
This system is designed for iPod only. You cannot connect any other
portable audio players.
To use an iPod, refer to the user’s guide of your iPod.
Sony cannot accept responsibility in the event that data recorded to
iPod is lost or damaged when using an iPod with this unit.
Changing the display
To
Press
Change
information on the
display
information on the
display
1)
DISPLAY repeatedly when the
system is on.
system is on.
Check the clock
when the system
is off
when the system
is off
2)
DISPLAY when the system is
off
off
3)
. The clock is displayed for 8
seconds.
1)
For example, you can view CD/MP3 disc information, such as;
track or file number during normal play.
track or file name (“ ”) during normal play.
artist name (“ ”) during normal play.
album or folder name (“
track or file number during normal play.
track or file name (“ ”) during normal play.
artist name (“ ”) during normal play.
album or folder name (“
”) during normal play.
total playing time while the player is stopped.
2)
The clock is displayed continuously while the iPod is being charged.
To turn off the clock display, press DISPLAY (See “To stop
charging the iPod”).
To turn off the clock display, press DISPLAY (See “To stop
charging the iPod”).
3)
The STANDBY indicator on the unit lights up when the system is
off.
off.
Notes on the display information
Characters that cannot be displayed appear as “_”.
Characters that cannot be displayed appear as “_”.
The following are not displayed:
total playing time for a CD-DA disc depending on the play mode.
total playing time and remaining playing time for an MP3 disc.
total playing time and remaining playing time for an MP3 disc.
The following are not displayed correctly:
folder and file names that do not follow either ISO9660 Level 1,
Level 2 or Joliet in the expansion format.
The following is displayed:
ID3 tag information for MP3 files when ID3 version 1 and version
2 tags are used (up to 62 characters).
Using optional audio components
To connect an optional headphones
Connect headphones to the PHONES jack on the
unit.
unit.
To connect an optional component
Connect additional audio component to the AUDIO
IN jack on the unit using an audio analog cord (not
supplied). Turn down the volume on the system, and
then select the AUDIO IN function.
IN jack on the unit using an audio analog cord (not
supplied). Turn down the volume on the system, and
then select the AUDIO IN function.
HCD-BX20i
HCD-BX20i/BX50BTi
7
Other Operations
Creating your own program
(Program Play)
(Program Play)
1
Press FUNCTION +/
(or FUNCTION on the unit)
repeatedly to select the CD function.
2
Press PLAY MODE
repeatedly until “PGM” appears
while the player is stopped.
3
Press
/ repeatedly until the desired
track or file number appears.
When programming files, press
+/
repeatedly
to select the desired folder, and then select the desired
file.
file.
Total playing time of program
(including selected track
or file)
(including selected track
or file)
Selected track or file
number
number
4
Press
(or ENTER on the unit)
to add the track
or file to the program.
“
. ” appears when the total program time
exceeds 100 minutes for a CD, or when you select a
CD track whose number is 21 or over, or when you
select an MP3 file.
CD track whose number is 21 or over, or when you
select an MP3 file.
5
Repeat steps 3 through 4 to program additional
tracks or files, up to a total of 25 tracks or files.
tracks or files, up to a total of 25 tracks or files.
6
To play your program of tracks or files, press
(or
CD
on the unit) .
The program remains available until you open the disc
tray. To play the same program again, press
tray. To play the same program again, press
(or
CD
on the unit) .
To cancel Program Play
Press PLAY MODE repeatedly until “PGM”
disappears while the player is stopped.
disappears while the player is stopped.
To delete the last track or file of the program
Press CLEAR while the player is stopped.
Presetting radio stations
You can preset your favorite radio stations and tune
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.
them in instantly by selecting the corresponding preset
number.
Use buttons on the remote to preset stations.
1
Tune in the desired station (See “Listening to the
radio”).
radio”).
2
Press TUNER MEMORY
.
Preset number
3
Press +/
repeatedly to select your desired
preset number.
If another station is already assigned to the selected
preset number, the station is replaced by the new
stations.
preset number, the station is replaced by the new
stations.
4
Press
.
5
Repeat steps 1 through 4 to store other stations.
You can preset up to 20 FM and 10 AM stations. The
preset stations are retained for about half a day even
if you disconnect the power cord or if a power failure
occurs.
preset stations are retained for about half a day even
if you disconnect the power cord or if a power failure
occurs.
6
To call up a preset radio station, press TUNING
MODE
MODE
repeatedly until “PRESET” appears, and
then press +/
repeatedly to select the desired
preset number.
Using the Timers
The system offers two timer functions. If you use the Play
Timer with the Sleep Timer, the Sleep Timer has priority.
Use buttons on the remote to use the timer functions.
Timer with the Sleep Timer, the Sleep Timer has priority.
Use buttons on the remote to use the timer functions.
Sleep Timer:
You can fall asleep to music. This function works even if
the clock is not set.
Press SLEEP repeatedly. If you select “AUTO,” the
system automatically turns off after the current disc stops
or in 100 minutes.
the clock is not set.
Press SLEEP repeatedly. If you select “AUTO,” the
system automatically turns off after the current disc stops
or in 100 minutes.
Play Timer:
You can wake up to CD, tuner or iPod at a preset time.
Make sure you have set the clock.
1
Prepare the sound source.
Prepare the sound source, and then press VOLUME
+/
+/
to adjust the volume.
To start from a specific track or file, create your own
program.
program.
2
Press TIMER MENU
.
3
Press
/ repeatedly to select “PLAY SET?,” and
then press
.
“ON” appears, and the hour indication flashes.
4
Set the time to start playback.
Press
/ repeatedly to set the hour, and then
press
.
The minute indication flashes. Use the procedure
above to set the minutes.
above to set the minutes.
5
Use the same procedure as in step 4 to set the time
to stop playback.
to stop playback.
6
Select the sound source.
Press
/ repeatedly until the desired sound
source appears, and then press
. The display
shows the timer settings.
7
Press
to turn off the system.
The system turns on 15 seconds before the preset time.
If the system is on at the preset time, the Play Timer
will not play.
If the system is on at the preset time, the Play Timer
will not play.
To activate or check the timer again
1
Press TIMER MENU
.
“TIMER SEL?” flashes in the display.
2
Press
.
3
Press
/ repeatedly to select “PLAY SEL?,” then
press
.
To cancel the timer
Repeat the same procedure as above until “TIMER
OFF?” appears in step 3, and then press
OFF?” appears in step 3, and then press
.
To change the setting
Start over from step 1.
Note on the iPod touch user
The Play Timer may not be activated depending on the status of the
connected iPod touch.
The Play Timer may not be activated depending on the status of the
connected iPod touch.
Tip
The Play Timer setting remains as long as the setting is not canceled
manually.
The Play Timer setting remains as long as the setting is not canceled
manually.
HCD-BX20i/BX50BTi
8
HCD-BX50BTi
Guide to parts and controls
This manual mainly explains operations using the remote, but the same operations can also be performed using the buttons on the unit having the same or similar names.
Unit (HCD-BX50BTi/Compact Disc Receiver)
Front panel
Top panel
Remote (RM-AMU009)
/ (power) button
Press to turn on the system.
Lights up when the system is turned off.
STANDBY indicator
Remote sensor
BLUETOOTH button
Press to make a connection,
disconnection, or pairing with a
Bluetooth device.
disconnection, or pairing with a
Bluetooth device.
BLUETOOTH indicator
Lights up when the Bluetooth function
is active.
is active.
; (open/close) button
Press to open or close the disc tray.
AUDIO IN jack
Connect to an optional audio
component.
component.
PHONES jack
Connect the headphones.
Playback buttons and function
buttons
Unit: BLUETOOTH V (play/
Unit: BLUETOOTH V (play/
pause) button
Press to select the Bluetooth function.
Press to start or pause playback of the
music on the Bluetooth device (Bluetooth
mobile phone, etc.).
Press to start or pause playback of the
music on the Bluetooth device (Bluetooth
mobile phone, etc.).
Click on the first or last page to see other HCD-BX20I / HCD-BX50BTI service manuals if exist.