Sony HBD-TZ145 Service Manual ▷ View online
HBD-TZ145
9
2-5. FRONT CABINET BLOCK
2 connector
(CN202)
(CN202)
3 connector
(CN203)
(CN203)
4 claw
1 Cut two wire ties.
Note: In reassembling, use new wire tie
to fasten the clamp same as before.
5 seven claws
6 front cabinet block
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
Bring the slack part to the front side.
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
WireVeWWiQJ
–5eDrriJKWYieZ–
HBD-TZ145
10
2-6. STANDBY BOARD, CONTROL BOARD
• Front cabinet inner view
6 USB grounding sheet
2 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
5 screw
(BVTP2.6)
(BVTP2.6)
4 STANDBY board
9 CONTROL board
CONTROL board
CONTROL board
STANDBY board
8 connector
(CN201)
(CN201)
3 two claws
1 two claws
claw
claw
7 two claws
WireVeWWiQJ
WireVeWWiQJ
HBD-TZ145
11
2-7. DVD MECHANISM DECK BLOCK
3 Solder the short-land.
2 connector
(CN301)
(See
(CN301)
(See
Fig.
A)
4 flexible cable
(CN300)
(CN300)
7 Remove the DVD
mechanism
mechanism
deck
block in the direction
of the arrow.
8 DVD mechanism deck block
1 Cut two wire ties.
(See
(See
Fig.
A)
<Fig. A>
Note 3:
When assembling the optical
pick-up block, remove the solder
of short-land after connecting the
flexible
cable.
Note 2:
In reassembling,
use new wire tie
to fasten the clamp
same as before.
5 two screws
(BVTT3
(BVTT3
u 7)
5 two screws
(BVTT3
(BVTT3
u 7)
6 claw
6 claw
– Rear right view –
Wire setting
wire tie
wire tie
tray
CONTROL board
MAIN board
POWER board
DVD mechanism deck
Bring the slack part
to the front side.
to the front side.
Check that this portion is not slack.
This portion must not touch the POWER board.
This portion must not touch the POWER board.
This portion must not touch the tray.
(Former type)
Note 5: When you install the connector, please install them
correctly. There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note 7: When installing the flexible
flat cable, ensure the colored
line. No slanting after insertion.
Insert is straight to the interior.
Insert is incline
flexible flat
cable
cable
OK
NG
connector
flexible flat
cable
cable
connector
Note 6: When installing the flexible flat
cable, check that the terminal is
not
damaged.
Terminal is damaged.
OK
NG
Ver. 1.4
Note 1:
When disconnecting the fl exible cable of optical pick-up block,
solder the short-land.
solder the short-land.
Note 4:
The DVD mechanism deck for this unit has been changed in the
midway of production. About the New/Former discrimination,
refer to “ABOUT THE DVD MECHANISM DECK” on page 4.
midway of production. About the New/Former discrimination,
refer to “ABOUT THE DVD MECHANISM DECK” on page 4.
HBD-TZ145
12
2-8. FFC HOLDER (Former type (for F-8829F1))
1 claw
1 claw
1 Insert the flexible cable
to the FFC holder.
FFC holder
2 Hang the flexible cable on
two claws of the FFC holder.
5 two claws
3 flexible cable
6 flexible cable
4 FFC holder block
– DVD mechanism deck bottom view –
+ow to instaOO IOe[ibOe cabOe
7 FFC holder
3 Pass a short side of
flexible cable through
the hole of the FFC
holder.
4 Pass a long side of flexible cable
through the hole of the FFC holder.
2 Remove the FFC holder
block in the direction of
the
arrow.
Ver. 1.4
Note:
The DVD mechanism deck for this unit has been changed in the
midway of production. About the New/Former discrimination,
refer to “ABOUT THE DVD MECHANISM DECK” on page 4.
midway of production. About the New/Former discrimination,
refer to “ABOUT THE DVD MECHANISM DECK” on page 4.
Click on the first or last page to see other HBD-TZ145 service manuals if exist.