DOWNLOAD Sony HBD-E385 / HBD-E390 / HBD-T39 Service Manual ↓ Size: 7.68 MB | Pages: 93 in PDF or view online for FREE

1 wire (flat type) (7 core)
 (CN5902)

2 wire (flat type)
 

3 CN5301 (11P)

5 three screws
 (+BV3 

4 four screws (+BV3 (3-CR))

7 heat sink (MB)

8 sheet, radiation

9 MB148 board

6 one screw (+B 3 u 5)

4 four screws
 (+BV3 

7 BD drive BPX-7

5 boss

6

1 flexible flat cable (45 core) (CN1101)

3 wire (flat type)
 

2 wire (flat type) (5 core) (CN1270)

Note: When you install the BD 
 

drive (BPX-7), please match 

 

the position of the boss two 

 places.

3 three screws (+BV3 (3-CR))

2 two screws (+BV3 (3-CR))

5 four screws (+BV3 (3-CR))

6 AMP board

4 heat sink (AMP)

1 CN3501 (2P)

1 one screw (+BV3 (3-CR))

6 five screws (+BV3 (3-CR))

7 switching regulator
 (SWR1)

3 CN1 (2P)

4 CN101 (4P)

5 CN4 (2P)

2 insulation, top (S)

6 two screws (S), float

0 insulator

4 Insert the thin 

0 insulator

qa device, optical

0 insulator

qs tape,

qj

qk cover, drive

qg flexible flat cable 

qh wire (flat type) 

1 four claws

5

7

8

9

2 two claws

3 holder, chuck assy (T)

qd wire (flat type)

qf tape, FFC

8

9 cover, drive

1 flexible flat cable (45 core)

6 wire (flat type)

2 Through the hole

3 wire (flat type) (9 core)

4 Through the hole

Note: This illustration sees the loading assy (T) from bottom side.

5 tape, FFC

7 tape,

COLD  RESET
The cold reset clears data except BD/DVD data stored in the RAM 
to initial conditions. Execute this mode when returning the unit to 
the customers.
Procedure:
1.  Press the [

?/1

] button to turn the power on.

2.  Press the [

x

] and [VOL –] buttons simultaneously and hold 

down (around 5 seconds).

3.  The message “RESET” appears on fl uorescent indicator tube, 

then becomes standby states.

DEMO  MODE
This mode let you lock the disc tray. When this mode is activated, 
the disc will not eject when the [

Z

] button is pressed. The message 

“DEMO. LOCK” will be displayed on the fluorescent indicator 
tube.
Procedure:
1.  Press the [

?/1

] button to turn the power on. 

2.  Press the [FUNCTION] button to select the “BD/DVD”.
3.  Press the [

x

] and [

Z

] buttons simultaneously and hold down 

until “DEMO. LOCK” or “DEMO OFF” displayed on the 
fluorescent indicator tube (around 5 seconds).

Releasing method:
Press the [

x

] and [

Z

] buttons simultaneously and hold down until 

“DEMO OFF” displayed on the fl uorescent indicator tube (around 
5 seconds).

PANEL TEST
Procedure:
1.  Press the [

?/1

] button to turn the power on.

2.  Press button in order of the [DISPLAY] 

[0] [0] [1] 

[SUBTITLE] on the remote commander (Make the interval 
when each button is pressed within two seconds).

3.  All segments in fl uorescent indicator tube are lighted up. And 

half segments in fl uorescent indicator tube are lighted up, oth-
ers half segments in fl uorescent indicator tube are lighted up, 
then all segments in fl uorescent indicator tube are lighted up. 
This operation is repeated.

4.  When all segments in fl uorescent indicator tube are lighted up 

in the state of step 3, press the [VOL +] button on the remote 
commander and model information is displayed on the fl uores-
cent indicator tube.

 

Each time the [VOL +] button on the remote commander is 
pressed, the display changes from destination information, 
STR version in this order, and returns to the model informa-
tion display.

5.  In the state of step 3, press the [FUNCTION] button on the 

remote commander and “K 0” is displayed on the fluorescent 
indicator tube.

 

“K 0” value increases whenever a button or sensor on the unit 
is pressed. However, once a button or sensor has been pressed, 
it is no longed taken into account.

 

All button and sensors on the unit are pressed, “OK” and “K 9” 
are alternately displayed on the fluorescent indicator tube.

Releasing method:
To release from this mode, press the [

?/1

] button.

FACTORY  INITIALIZE
Return all of the unit setting to their factory defaults.

Note 1: Disconnect the following connections when you use this mode.
 

   

 USB

 

   

 LAN

Note 2: The operation in this mode must use a remote commander and TV 

monitor.

Procedure:
1.  Press the [

?/1

] button to turn the power on. 

2.  Press the [HOME] button on the remote commander, and the 

home menu is displayed.

3. Select 

“Setup” 

 “Resetting”, and press the [ ] button on the 

remote commander.

4.  Select “Initialize Personal Information”, and press the [

] 

button on the remote commander.

5.  Select “OK”, and press the [

] button on the remote com-

mander.

Resetting

Easy Setup

Initialize Personal Information
Erase personal data when disposing

Reset to Factory Default Settings

Initialize Personal Information

OK

Cancel

The information below will be deleted.
Do you want to proceed?
- Playback history
- Internet video utilization information