DOWNLOAD Sony GTK-X1BT Service Manual ↓ Size: 6.95 MB | Pages: 78 in PDF or view online for FREE

 It is possible to also remove ones of Lch and Rch.

4 

8 

6 

2 

7 

7 

3 

3 

5 six screws
 ((3.5 

u 20), tapping)

1 six screws
 ((3.5 

u 20), tapping)

[PANEL  TEST  MODE]
This mode is used to check the liquid crystal display panel, LEDs, 
keys, [MASTER VOLUME] jog, model, destination and software 
version.
Procedure:
1.  Press [BASS BAZUCA] button and [TUNING +] button si-

multaneously and hold 3 seconds.

2.  All LEDs and segments in liquid crystal display panel are 

lighted up.

3. When 

[] button is pressed after all LEDs and segments in 

liquid crystal display panel light up, alternate segments in liq-
uid crystal display panel and LEDs would light up. If you press 
[] button again, another half of alternate segments in liquid 
crystal display panel and LEDs would light up. Pressing [] 
button again would cause all segments in liquid crystal dis-
play panel and LEDs (except Speaker LED – light up BLUE) 
light up. Liquid crystal display panel will light up 8 character 
UNION JACK display and all LEDs are OFF if [] is pressed 
again.

4.  When you want to enter to the software version display mode, 

press [+] button. The model information appears on the liq-
uid crystal display panel.

 Press 

[+] button again to view the destination information.

 

(Displayed characters/values in the following fi gure are example)

5.  During the destination information display, press [+] button. 

Each time [+] button is pressed, the liquid crystal display 
panel shows the version of each category software in the fol-
lowing sequence: SC, UI, PF, SYS, M1, M2, I1, I2, ST, TA, 
TAS, TM, BTM, BT, NFC and return back to model informa-
tion display.

 

(Displayed characters/values in the following fi gure are ex-
ample)

+] 

6.  When [FUNCTION] button is pressed while the version num-

bers are being displayed except model and destination, the date 
of the software creation appears. When [FUNCTION] button 
is pressed again, the display returns to the software version 
display.

7. Press 

[-] button, the key check mode is activated.

8.  In the key check mode, the liquid crystal display panel displays 

“K 0    V0”.

 

Each time a button is pressed, “K” value increases. However, 
once a button has been pressed, it is no longer taken into ac-
count. 

 

“V” value increases in the manner of 0, 1, 2, 3 ... if [MASTER 
VOLUME] knob is turned clockwise, or it decreases in the 
manner of 0, 9, 8, 7  ... if [MASTER VOLUME] knob is turned 
counterclockwise.

9.  To release from this mode, press two buttons in the same man-

ner as step 1, or disconnect the power cord.

[COLD  RESET]
The cold reset clears all data including preset data stored in the 
data fl ash to initial conditions. Execute this mode when returning 
the set to the customer.
Procedure:
1.  Press [TUNING +] button and ['/1] button simultaneously 

for 3 seconds.

2.  “COLD RST” appears on the liquid crystal display panel. Af-

ter that, the liquid crystal display panel becomes blank for a 
while, and the system is reset.

X

CE2

[HISTORY  MODE]
This mode is used to check important data stored in the system 
when PROTECTOR happen.
Procedure:
1.  During demo mode, press [LED SPEAKER] button and [u] 

for 5 seconds to mode in to history mode.

2.  Press the [TUNING +/M >] or [TUNING -/m .] 

button to check history data stored.

Protector Count

P C O U N

T  

Protector Type (refer protector 
kind test mode)

AMPL

E01

PWR1

E02

PWR2

E03

P

T

   

Single Power On Time

1 *h *h *h *h *h *m *m

Total Power On Time

2 *h *h *h *h *h *m *m

Input Function

F

     

Volume

V O

L

  

Actual Attenuation

A

T

T

  

Low EQ Level

L O W

  

Mid EQ Level

M

I

D

  

High EQ Level

H

I

G H

  

VACS Level

V

A C S

 

AP VACS Level

A P V

A C S



Surround Setting

S U R R

  

DJ Effect Setting

D

J

  

 

Bass Bazuca Setting

B

A S

S

  

Vertical Sound Setting

V

E R

T

  

PARTY CHAIN 

P

C H

  

 

•  To release from History Mode.

 

  To release from this mode, press ['/1] button.

[PROTECTOR  TEST  DISPLAY  TEST  MODE]
This mode is used to check types of protect occurred during pro-
tector on.
Procedure:
1.  During protection on, liquid crystal display panel shows blink-

ing message “PROTECT  EXX”.

 

“EXX” – represent the error code.

2.  Press [FUNCTION] button and [u] button simultaneously.
3.  Liquid crystal display panel display will toggle between 

“PROTECT” message & protector kind message display. 
Bellow table explains on protector kind.

E01

“AMP”

Defect of AMP circuit

E02

“PWR SUP1”

Defect of power supply 
circuit to AMP

E03

“PWR SUP2”

Defect of USB port or 
iPod/iPhone connector.

 

•  To release from this mode.

Press [FUNCTION] button and [u] button simultane-
ously again or unplug and re-plug in the power cord.

The following defect might be possible.

OTP (Over Temperature 
Protection)

Unusual heat up of AMP IC 
by improper assembly of 
heatsink, etc.. 

OCP (Over Current 
Protection)

The overcurrent condition to 
DAMP IC occurs by defect 
of DAMP IC or defect of PS 
output line.

DC Detection

DC appears in SP terminal by 
defect of AMP IC or output is 
short-circuit.

The following defect might be possible.

Under Voltage

IC701 output is below 12V.

RESET defect

Reset signal status from micon 
is not 'H' .

There is possibility of unusual power supply of any of the 
AMP IC, IC812 (6V regulator from SMPS supply) or fan is 
blocked.

There is possibility of the USB port or iPod/iPhone connector 
is short-circuited.

 

• To release from this mode.

Press [FUNCTION] button and [u] button simultaneously 
again or unplug and re-plug in the power cord.

Procedure :
1.  Turn the power on.
2.  Input the following signal from Signal Generator to FM an-

tenna input directly.

Carrier frequency : A = 87.5 MHz, B = 98 MHz, C = 108 MHz
Deviation 

: 75 kHz

Modulation 

: 1 kHz

ANT input 

: 35 dBu (EMF)

Note: Use 75 ohm coaxial cable to connect signal generator and the unit. 

You cannot use video cable for checking.

 

  Use signal generator whose output impedance is 75 ohm. 

 
3.  Set to FM tuner function and tune A, B and C signals.
4. Confi rm “TUNED” is lit on the display for A, B and C signals.
 
When the selected station signal is received in good condition, 
“TUNED” is displayed.