Sony FST-ZX100D / FST-ZX80D / LBT-ZX100D / LBT-ZX80D / SS-CT100D / SS-WGV100D / SS-ZX100D / SS-ZX100DP / SS-ZX80DP Service Manual ▷ View online
SERVICE MANUAL
Ver. 1.1 2007.0
3
SPECIFICATIONS
9-887-256-02
2007
C
05-1
© 2007.0
3
Sony Corporation
Home Audio Division
Published by Sony Techno Create Corporation
Published by Sony Techno Create Corporation
SPEAKER SYSTEM
•
JIG
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
When disassembling the set, use the following jig (for
speaker removal).
Part No.: J-2501-238-A JIG FOR SPEAKER REMOVAL
SS-CT100D/WGV100D/ZX80DP/
ZX100D/ZX100DP
SS-ZX80DP
SS-ZX100DP
Front Speaker
SS-ZX100D
Surround Speaker
SS-ZX100D
Front/Surround speaker SS-ZX100D
Speaker system
2-way, bass-reflex type,
magnetically shielded
magnetically shielded
Speaker units
Woofer
Woofer
22 cm (8
5
/
8
in.), cone type
Tweeter
5 cm (2 in.), cone type
×
2
Nominal impedance
6 ohms
Dimensions (w/h/d)
Approx. 308
×
365
×
480 mm (12
1
/
8
×
14
3
/
8
×
18
7
/
8
in.)
Mass
Approx. 9.3 kg (20 lb 9 oz) net per
speaker
speaker
Center Speaker SS-CT100D
Speaker system
Full range, 2-unit,
bass-reflex type,
magnetically shielded
bass-reflex type,
magnetically shielded
Speaker units
Full range
Full range
8 cm (3
1
/
8
in.), cone type
×
2
Nominal Impedance
16 ohms
Dimensions (w/h/d)
Approx. 268
×
107
×
117 mm (10
1
/
2
×
4
1
/
4
×
4
5
/
8
in.)
Mass
Approx. 1.6 kg (3 lb 9 oz)
Subwoofer
SS-WGV100D
SS-WGV100D
Subwoofer system
1-way, 1-unit,
bass-reflex type,
magnetically shielded
bass-reflex type,
magnetically shielded
Speaker units
Subwoofer:
Subwoofer:
20 cm (7
7
/
8
in.), cone type
Nominal impedance
8 ohms
Dimensions (w/h/d) (Approx.)
281
×
362
×
338.5 mm
(11
×
14
1
/
4
×
13
3
/
8
in.)
Mass (Approx.)
6.8 kg (14 lb 16 oz)
Design and specifications are subject to change
without notice.
without notice.
US Model
SS-CT100D/ZX80DP/ZX100D
E Model
SS-CT100D/WGV100D/ZX80DP/
ZX100D/ZX100DP
•
SS-CT100D is center speaker in FST-ZX80D/ZX100D/LBT-ZX80D/ZX100D.
•
SS-WGV100D is subwoofer in FST-ZX100D/LBT-ZX100D.
•
SS-ZX100D is front and surround speakers in FST-ZX80D/ZX100D/LBT-ZX80D/ZX100D.
Photo: SS-CT100D
Photo: SS-WGV100D
Photo: SS-ZX100D
•
SS-ZX80DP is package speaker of front and surround speakers in FST-ZX80D/LBT-ZX80D.
•
SS-ZX100DP is package speaker of front and surround speakers in FST-ZX100D/LBT-ZX100D.
2
SS-CT100D/WGV100D/ZX80DP/ZX100D/ZX100DP
Notes on chip component replacement
•
Never reuse a disconnected chip component.
•
Notice that the minus side of a tantalum capacitor may be
damaged by heat.
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
•
Unleaded solder melts at a temperature about 40 ˚C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 ˚C.
Caution: The printed pattern (copper foil) may peel away if
Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
•
Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
occur such as on IC pins, etc.
•
Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
SECTION 1
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Subwoofer
(SS-WGV100D)
2
1
SUBWOOFER ON/OFF 1
SUBWOOFER LEVEL 2
SUBWOOFER LEVEL 2
ALPHABETICAL ORDER
A – Z
3
SS-CT100D/WGV100D/ZX80DP/ZX100D/ZX100DP
Note:
Follow the disassembly procedure in the numerical order given.
2-1. FRONT PANEL BLOCK (SS-WGV100D)
SECTION 2
DISASSEMBLY
4
front panel block
2
Insert the jig (J-2
50
1-238-A) into a space
made by inserting the screwdriver,
and raise the front panel assy gradually.
and raise the front panel assy gradually.
3
Raise the front panel assy a little by little
from bottom to top of the set.
from bottom to top of the set.
1
Insert a flat-tip screwdriver into a recess
in the bottom of the set
to raise the front panel assy a little.
in the bottom of the set
to raise the front panel assy a little.
4
SS-CT100D/WGV100D/ZX80DP/ZX100D/ZX100DP
•
Note for Printed Wiring Boards and Schematic Diagrams
Note on Printed Wiring Board:
•
X
: parts extracted from the component side.
•
Y
: parts extracted from the conductor side.
•
: Pattern from the side which enables seeing.
(The other layers' patterns are not indicated.)
•
Indication of transistor
Note on Schematic Diagram:
•
All capacitors are in
µ
F unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
and tantalums.
•
All resistors are in
Ω
and
1
/
4
W or less unless otherwise
specified.
•
C
: panel designation.
•
A
: B+ Line.
•
Voltages are dc with respect to ground under no-signal
conditions.
no mark : POWER ON
conditions.
no mark : POWER ON
•
Voltages are taken with a VOM (Input impedance 10 M
Ω
).
Voltage variations may be noted due to normal produc-
tion tolerances.
tion tolerances.
SECTION 3
DIAGRAMS
3-1. PRINTED WIRING BOARD (SS-WGV100D)
: Uses unleaded solder.
R1401
R1402
R1403
R1404
Q1400
R1405
R1406
JR1402
JR1400
D1400
S1400
C1400
CN1400
SW1400
C1401
SW1400
E
1-868-600-
11
(11)
SWPANEL BOARD
SUBWOOFER
ON/OFF
SUBWOOFER
LEVEL
1
4
TO
HCD-ZX100D
–12dB
–6dB
–3dB
0dB
r
r
r
A
B
C
D
E
1
2
3
