Sony FST-GTK33IP / RDH-GTK11IP / RDH-GTK33IP Service Manual ▷ View online
FST-GTK11iP/GTK33iP/RDH-GTK11iP/GTK33iP
25
2-16. POWER CORD (AC1)
2 cover (power-PWB) block
1 screw
(BV/ring)
1 screw
(BV/ring)
1 screw
(BV/ring)
4 connector
(CN901)
5 power cord (AC1)
3 Remove the ferrite core
from coating clip.
coating clip
Note 1: Please spread a sheet under a unit
not to injure front grille.
– Top rear view –
power cord (AC1)
ferrite core
power cord (AC1)
cushion (E)
ferrite core
cushion (E)
70 ± 5 mm
50 mm
Roll the power cord once.
Power cord setting
wire setting
MAIN board
SMPS board
Note 2: When you install the connector, please
install
install
themcorrectly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
FST-GTK11iP/GTK33iP/RDH-GTK11iP/GTK33iP
26
2-17. GTK11-SMPS BOARD (GTK11iP) /GTK33-SMPS BOARD (GTK33iP)
The portion which applies bond:
2 screw
(BV/ring)
2 screw
(BV/ring)
2 two screws
(BV/ring)
2 three screws
(BV/ring)
3 GTK11-SMPS board (GTK11iP)/
GTK33-SMPS board (GTK33iP)
1 connector (CN811)
– Top rear view –
Note 2: When you install the connector, please
install
install
themcorrectly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
Note 1: Please spread a sheet under a unit
not to injure front grille.
Note 3: Please apply 1 g or more of bonds on cushion (PW).
%oQG Ii[aWioQ
Use bond
Part No.
Description
7-432-912-52 BOND, SONY (SC-608LV)
cushion (PW)
cushion (PW)
Note 4: Please apply the bond to both
Note 4: Please apply the bond to both
SMPS board and cushion (PW).
GTK11-SMPS board (GTK11iP)/
GTK33-SMPS board (GTK33iP)
GTK33-SMPS board (GTK33iP)
cushion (PW)
cushion (PW)
cushion (PW)
cushion (PW)
cushion (PW)
chassis
guide line
guide line
3 mm
2 mm
$WWaFKPeQW poViWioQ oI aGGeG FXVKioQ 3:
Ver. 1.1
FST-GTK11iP/GTK33iP/RDH-GTK11iP/GTK33iP
27
2-18. CHASSIS BLOCK, REINFORCEMENT (BACK PANEL) BLOCK
2-19. ORNAMENT BASE BLOCK
(GTK33iP: US)
Note: Please spread a sheet under a unit
not to injure front grille.
1 two screws
(BV/ring)
2 shield (main-UB)
3 three tapping screws
(3.5
u 20)
5 three tapping screws
(3.5
u 20)
3 two tapping screws
(3.5
u 20)
3 two tapping screws
(3.5
u 20)
3 tapping screw
(3.5
u 20)
5 tapping screw
(3.5
u 20)
5 tapping screw
(3.5
u 20)
5 tapping screw
(3.5
u 20)
6 coating clip
7 reinforcement (back panel)
block
7 reinforcement (back panel)
block
4 chassis block
– Top rear view –
3 ornament base block
1 three tapping screws
(3.5
u 20)
2 Peel off four adhessive
sheets.
– Bottom front view –
Ver. 1.1
FST-GTK11iP/GTK33iP/RDH-GTK11iP/GTK33iP
28
total twenty bosses
3
2 Insert the jig into a space and raise
the front panel assy.
Note
1: When using a jig, please work
so as not to injure front panel
assy and SPK box assy.
2 Insert the jig into a space and raise
the front panel assy.
Note
1: When using a jig, please work
so as not to injure front panel
assy and SPK box assy.
3
All bosses are removed while moving jig in the direction
of the arrow, and front panel assy is removed.
1 Insert the flat-blade driver into a side space
and raise the front panel assy.
– Bottom front view –
Note 2: When you install the connector, please
install
install
themcorrectly.
There is a possibility that this machine
damages when not correctly installing it.
Insert is shallow
Insert is straight
to the interior.
to the interior.
connector
Insert is incline
connector
connector
connector
connector
connector
NG
OK
NG
7 front panel assy
6 terminal (red)
6 terminal (red)
6 terminal (black/red)
6 terminal (black/red)
4 Remove the front panel assy
in the direction of an arrow.
:ire VettinJ
:ire VettinJ
OK
NG
OK
NG
5 connector
(CN551)
2-20. FRONT PANEL ASSY
• JIG
When disassembling the set, use the following jig (for speaker
When disassembling the set, use the following jig (for speaker
removal).
Part
No.
Description
J-2501-238-A
JIG FOR SPEAKER REMOVAL
Click on the first or last page to see other FST-GTK33IP / RDH-GTK11IP / RDH-GTK33IP service manuals if exist.