Sony FH-SR1D / HCD-SR1D Service Manual ▷ View online
HCD-SR1D
9
2-6. CABINET (FRONT) BLOCK
2-7. AMP BOARD, TUNER BOARD
(African)
1 Insert the flat-head screwdriver in the hole
of the chassis, and push the lever in the
direction of the arrow.
3 two claws
qd claw
qf cabinet (front) block
qd claw
4 panel (DVD)
bottom side
2
0 screw
(BVTT3
u 7)
qs three screws
(BVTT3
u 8)
5 connector
(CN1)
9 connector
(RB903)
6 connector
(CN404)
8 connector
(CN906)
qa lug wire
7 FFC 11PL80P125
(FFC3)
(CN401)
– Rear side view –
5
1 Cut two binding bands.
binding band binding band
2 connector
(CN907)
Note: In reassembling, use new binding band
to fasten the clamp same as before.
MAIN board
AMP board
power transformer
4 lug wire
6 FFC 16PL100P125 (FFC2)
(CN405)
7 AMP board
8 TUNER board
:ire seWWiQJ
rear side
3 two screws
(BVTT3
u 6)
3 screw
(BVTT3
u 6)
HCD-SR1D
10
1 Cut two binding bands.
Note 2: In reassembling, use new binding band
to fasten the clamp same as before.
2 connector (CN902)
Note
1: It is possible to insert it in both CN902 and CN905
on POWER board. It is printed on the POWER board
with “To Transformer” at CN902 and “AC IN: 220 -
240V” at CN905. When you connect the power cord
with the CN905 on POWER board, insert it according
to the instruction of the print so as not to make a mistake.
3 connector
(CN904)
CN905
CN902
:LUHVHWWLQJ
binding band
binding band
POWER board
MAIN board
power transformer
–5HDUVLGHYLHZ–
$IULFDQ
7 connector
(RB903)
4 connector (CN906)
6 connector (CN901)
5 connector (CN907)
8 two screws
(BVTT3
u 7)
9 POWER board
rear side
2-8. POWER TRANSFORMER (T901)
2-9. POWER BOARD
1 Cut the binding band.
Note 2: In reassembling, use new binding band
to fasten the clamp same as before.
2 connector (CN902)
Note
1: It is possible to insert it in both CN902 and CN905 on POWER board.
It is printed on the POWER board with “To Transformer” at CN902 and
“AC IN: 220 - 240V” at CN905.
When you connect the power cord with the CN905 on POWER board,
insert it according to the instruction of the print so as not to make a mistake.
3 connector
(CN904)
CN905
CN902
4 four screws
(PWH4
u 7)
(Except
Saudi
Arabia)
(PWH4
u 6)
(Saudi
Arabia)
5 power transformer
(T901)
:LUHVHWWLQJ
binding band
POWER board
power transformer
rear side
–5HDUVLGHYLHZ–
Ver. 1.1
HCD-SR1D
11
2-10. DVD BLOCK
6
1 FFC 10PL150P125
(FFC1)
(CN403)
2 FFC 16PL100P125 (FFC2)
(CN402)
3 flexible flat cable (5 core)
(FFC4)
(CN10)
4 connector
(CN9)
7 three screws
(BVTT3
u 7)
9 two screws
(BVTT3
u 7)
9 screw
(BVTT3
u 7)
8 dust cover block
0 DVD block
Note: Do not remove this connector (CN8) at this point.
It is necessary to process electrostatic measures of
optical
pick-up.
5 four screws
(BVTT3
u 6)
HCD-SR1D
12
2-11. MAIN BOARD
Note 1: When disconnecting the fl exible cable (24 core) of optical pic-up block, solder the short-land.
2-12. FFC HOLDER
1 Solder the short-land.
Note 2: When assembling the optical pick-up block,
remove the solder of short-land after
connecting the flexible cable (24 core).
2 flexible cable (24 core)
(FFC5)
(CN8)
3 MAIN board
– DVD mechanism deck bottom view –
1 two claws
1 two claws
2 two claws
3 FFC holder
Note: Remove the FFC holder from the
original set and install it again.
– DVD mechanism deck bottom view –
Click on the first or last page to see other FH-SR1D / HCD-SR1D service manuals if exist.