Sony DVP-NS29 / DVP-NS30 / DVP-NS32 / DVP-NS33 / DVP-NS52P / HTP-32DW / HTP-32SS Service Manual ▷ View online
2-1
DVP-NS30/NS32/NS33/NS52P
Note: Follow the disassembly procedure in the numerical order given.
2-1. UPPER CASE
SECTION 2
DISASSEMBLY
2-2. FRONT PANEL ASSEMBLY
4
Tapping Screw
5
Tapping Screw
3
Tray Cover
6
Three Screws
+BV3
(3-CR)
1
Dust Cover
2
7
Front Panel Assembly
5
Claw
3
Claw
2
Claw
6
Claw
1
Claw
a
b
b
4
Claw
2-2
DVP-NS30/NS32/NS33/NS52P
2-3. LOADING ASSEMBLY
1
Three Screws
+BV3
(3-CR)
2
Loading Assembly
1
FMO-004 Flat Flexible Cable (CN101, 24P)
3
FMS-003 Flat Flexible Cable (CN202, 5P)
2
MD-108 Harness (CN201, 6P)
2-3
DVP-NS30/NS32/NS33/NS52P
2-4. OPTICAL DEVICE (KHM-310CAA/C2RP)
5
FMD-004 Flat Flexible Cable (CN101, 24P)
4
MD-108 Harness (CN201, 6P)
1
Four Insulator Screws
6
Two Insulator
6
Two Insulator
3
Optical Device
(KHM-310CAA/C2RP)
2
FFC Holder
Caution Point on the Laser Diode:
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
Laser Diode in the optical Device is very sensitive to Surge
Current or ElectroStatic Discharge (ESD):
After take-out FMD-004 Flexible cable from CN101 of
MV-045 board immediately ground FMD-004 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
MV-045 board immediately ground FMD-004 Flexible cable
pattern using short clip. Metal paper clip can be used as
short clip.
Note:
Solder short land before
remove the harness from
24 pin BU connector.
remove the harness from
24 pin BU connector.
Shortland Position
2-4
DVP-NS30/NS32/NS33/NS52P
2-5. MV-045, IF 124 and ER-037 BOARDS
2-6. SWITCHING REGULATOR
5
FMD-004 Flat Flexible Cable
(CN101, 24P)
6
FEM-001 Flat Flexible Cable
(CN302,
21P)
0
ER-037 Board
8
MV-045 Board
2
MD-108 Harness
(CN201,
6P)
3
FMS-003 Flat Flexible Cable
(CN202,
5P)
7
Five Screws
+BV3
(3-CR)
6
Two Screws
+BV3
(3-CR)
1
Five Screws
+BV3
(3-CR)
4
(Board to Board) Connector
(CN401,
17P)
a
c
d
d
a
c
b
9
IF-124 Board
d
2
Two Screws
+BV3
(3-CR)
1
PM-119 Harness Connector
(CN201,
10P)
3
Power Board
Note:
Caution Point on the PWB IF-124
When handling IF-124 PWB avoid contact with
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
the sharp metal edge on the top side of Vacuum
Fluorescent Display (ND401).
Click on the first or last page to see other DVP-NS29 / DVP-NS30 / DVP-NS32 / DVP-NS33 / DVP-NS52P / HTP-32DW / HTP-32SS service manuals if exist.