Sony DHC-MD777 / HMC-MD777 Service Manual ▷ View online
– 17 –
CD MECHANISM DECK SECTION (CDM53-K1BD33)
4
two screws
(BV3
(BV3
×
8)
5
Remove the CD mechanism deck section (CDM53-K1BD33)
in the direction of the arrow.
in the direction of the arrow.
3
four screws
(BV3
(BV3
×
8)
6
wire (flat type) (19 core)
(CN300)
(CN300)
2
wire (flat type) (17 core)
(CN701)
(CN701)
1
connector
(CN713)
(CN713)
RELAY BOARD
1
wire (flat type) (23 core)
(CN451)
(CN451)
1
wire (flat type) (13 core)
(CN453)
(CN453)
2
screw
(BV3
(BV3
×
8)
3
connector
(CN456)
(CN456)
4
Remove the RELAY board
in the direction of the arrow.
in the direction of the arrow.
– 18 –
MD MECHANISM DECK SECTION (MDM-C1F)
1
four screws
(BV3
(BV3
×
8)
3
connector
(CN106)
(CN106)
2
MD mechanism deck section
(MDM-C1F)
(MDM-C1F)
MICROCOMPUTER BOARD, MAIN BOARD
3
Remove the MICROCOMPUTER
board in the direction of the arrow.
board in the direction of the arrow.
7
Remove the MAIN
board in the direction
of the arrow.
board in the direction
of the arrow.
5
screw
(BV3
(BV3
×
8)
1
two connectors
(CN304, 305)
(CN304, 305)
6
PWB holder
1
connector
(CN306)
(CN306)
5
screw
(BV3
(BV3
×
8)
4
three screws
(BV3
(BV3
×
8)
2
PWB holder
A
B
– 19 –
CD BASE UNIT (BU-K1BD33)
2
CD base unit
(BU-K1BD33)
(BU-K1BD33)
1
two screws
(PTPWHM2.6)
(PTPWHM2.6)
1
two screws
(PTPWHM2.6)
(PTPWHM2.6)
FITTING BASE (GUIDE/MAGNET) ASS’Y
2
four screws
(BVTP2.6)
(BVTP2.6)
4
two screws
(BVTP2.6)
(BVTP2.6)
7
four screws
(BVTP2.6)
(BVTP2.6)
4
two screws
(BVTP2.6)
(BVTP2.6)
3
fitting base (guide) ass’y
8
fitting base (magnet) ass’y
1
two connectors
(CN709, 715)
(CN709, 715)
5
bracket
(chassis)
(chassis)
6
connector
(CN710)
(CN710)
– 20 –
TRAY (SUB)
pulley (LD)
slider (selection)
pulley (mode)
stocker
tray (sub)
R
L
1
Rotate the pulley (LD) and move the slider (selection)
in the direction of the arrow
in the direction of the arrow
L
.
2
Rotate the pulley (mode) in the direction of the arrow
and adjust the tray (sub) of object.
and adjust the tray (sub) of object.
3
Rotate the pulley (LD) and move the slider (selection)
in the direction of the arrow
in the direction of the arrow
R
.
4
Rotate the pulley (mode) in the direction of the arrow
and remove the tray (sub) of object.
and remove the tray (sub) of object.
CHASSIS (MOLD B) ASS’Y, STOCKER, SLIDER (SELECTION)
Note: Refer to page 21, 22 when install.
5
stocker
7
slider (selection)
8
washer
9
compression spring
3
gear (eject)
4
two step screws
1
three screws
(BVTP2.6)
(BVTP2.6)
6
two screws
(PTPWHM2.6)
(PTPWHM2.6)
4
two step screws
pulley (LD)
2
chassis (mold B) ass’y
Note: Rotate the pulley (LD) and
move the slider (selection)
to left.
to left.
Click on the first or last page to see other DHC-MD777 / HMC-MD777 service manuals if exist.