Sony DHC-MD7 / ST-M9 Service Manual ▷ View online
— 5 —
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
— 6 —
— 7 —
0DB=1
µ
V
Note: As a front-end (FE1) is difficult to repair if faulty, replace it
with new one.
AM SECTION
AM Tuned Level Adjustment
Note: FM Tuned Level adjustment should be performed after this
AM Tuned Level Adjustment.
Setting:
Band: AM
Procedure:
Band: AM
Procedure:
loop antenna
set
30% amplitude
modulation by
400Hz signal
modulation by
400Hz signal
1. Set the output of SSG so that the input level of the set becomes
55 dB.
2. Tune the set to 999 kHz or 1,000 kHz.
3. Adjust RV1 to the point (moment) when the TUNED indicator
3. Adjust RV1 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location: MAIN board
FM SECTION
FM Tuned Level Adjustment
Note: This adjustment should be performed after the AM Tuned
Level Adjustment.
Setting:
Band: FM
Procedure:
1. Supply a 26 dB 98 MHz signal from the ANTENNA terminal.
Band: FM
Procedure:
1. Supply a 26 dB 98 MHz signal from the ANTENNA terminal.
AM RF SSG
60cm
loop antenna
(Supplied accessories)
(Supplied accessories)
Modulation: 999 kHz (at 9 kHz step)
1,050 kHz (at 10 kHz step)
output level: 55 dB
Field strength dB (
µ
V/m) = SSG output level dB (
µ
V/m) –26dB.
AM antenna
terminal (TM1)
terminal (TM1)
TM1
FE1
RV2
FM TUNED Level
Adjustment
FM TUNED Level
Adjustment
RV1
AM TUNED Level
Adjustment
AM TUNED Level
Adjustment
SECTION 3
ELECTRICAL ADJUSTMENT
Carrier frequency:98MHz
Modulation:
Modulation:
AUDIO 1kHz, 75kHz
deviation (100%)
deviation (100%)
Output level:
26dB (at 75
Ω
open)
set
FM ANTENNA terminal
(TM1)
(TM1)
75
Ω
coaxial
FM RF SSG
2. Tune the set to 98 MHz.
3. Adjust RV2 to the point (moment) when the TUNED indicator
3. Adjust RV2 to the point (moment) when the TUNED indicator
will change from going off to going on.
Adjustment Location: MAIN board
Adjustment Location
[MAIN BOARD] – Component Side –
[MAIN BOARD] – Component Side –
— 8 —
4-1. IC PIN FUNCTION
Pin Name
I/O
Function
SECTION 4
DIAGRAMS
• IC201 SYSTEM CONTROL (
µ
PD78013GC-652-AB8)
I
I
I
I
I
O
I
—
—
O
O
—
—
—
—
—
—
I
I
I
O
O
O
—
—
—
O
O
O
O
O
O
I
O
I
I
I
I
I
—
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
DESTINATION
DESTINATION
DESTINATION
DESTINATION
IF +50
IF –50
BACK UP
NC
Vss
POWER
MUTE
ANALOG BUS
NC
NC
AM MONO
AM/FM
IFNG
STEREO
SIGNAL
DATA IN
DATA OUT
CLOCK
CE
Vss
NC
NC
ONCE
DAILY
REC
SLEEP
ENCODER
NEXT
ENCODER IN B
AU BUS OUT
RESET
AU BUS IN
ENCODER IN A
RDS-CLOCK
RDS-DATA
V
DD
Destination selection input.
Not used. (Ground)
Back up mode input.
Not used. (Open)
Ground
Power ON/OFF control.
Mute output.
Not used. (Open)
STEREO signal detection input.
TUNED signal detection input.
Data input. (LC72130, PLL)
Data output. (LC72130, PLL)
Clock output. (LC72130, PLL)
Chip Enable output. (LC72130, PLL)
Ground
Not used. (Open)
LED drive output.
ENCODER input. (B)
Audio bus output.
SYSTEM RESET input.
Audio bus input.
ENCODER input. (A)
RDS clock input. (Not used) (Ground)
RDS data input. (Not used) (Ground)
Power supply 5V.
Click on the first or last page to see other DHC-MD7 / ST-M9 service manuals if exist.