Sony DAV-X10 / HCD-X10 Service Manual ▷ View online
HCD-X10
13
2
three screws
(BVTP3
(BVTP3
×
8)
2
three screws
(BVTP3
(BVTP3
×
8)
1
wire (flat type) (15 core)
(CN101)
(CN101)
3
top block
– Bottom view –
3-4. TOP BLOCK
3-5. TOP PANEL
1
ten screws
(BVTP3
(BVTP3
×
6)
2
top panel
HCD-X10
14
2
wire (flat type) (5 core)
(CN1301)
(CN1301)
3
wire (flat type) (21 core)
(CN514)
(CN514)
qs
wire (flat type)
(17 core: US, Canadian model(CN502)/
15 core: AEP UK model) (CN504)
(17 core: US, Canadian model(CN502)/
15 core: AEP UK model) (CN504)
qd
wire (flat type)
(17 core: US, Canadian model)
(CN501)/
19 core: AEP UK model) (CN503)
(17 core: US, Canadian model)
(CN501)/
19 core: AEP UK model) (CN503)
4
wire (flat type) (11 core)
(CN507)
(CN507)
5
wire (flat type) (17 core)
(CN506)
(CN506)
qf
six screws
(BVTP3
(BVTP3
×
6)
qh
screw
(BVTT3
(BVTT3
×
8)
qg
two clamps (L35)
qj
ground plate (main)
qk
MAIN board
0
two screws
(BVTP3
(BVTP3
×
6)
qa
ground plate (ITA)
6
connector (CN1300)
7
connector
(CN412)
(CN412)
8
connector
(CN505)
(CN505)
9
connector
(CN515)
(CN515)
1
Perform work with this wire (flat type) (24 core) connected,
or make a bridge as mentioned above and then disconnect the wire (flat type) (24 core).
(Optical pick-up will be destroyed without bridging.)
On the contrary at the installation, connect the wire (flat type) (24 core) first,
and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
(Refer to DISASSEMBLY 3-3. OPTICAL PICK-UP BLOCK (KHM-310CAA or KHM-313CAA)) (page 12)
or make a bridge as mentioned above and then disconnect the wire (flat type) (24 core).
(Optical pick-up will be destroyed without bridging.)
On the contrary at the installation, connect the wire (flat type) (24 core) first,
and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
(Refer to DISASSEMBLY 3-3. OPTICAL PICK-UP BLOCK (KHM-310CAA or KHM-313CAA)) (page 12)
PRECAUTION WHEN REMOVING WIRE (FLAT TYPE) (24 CORE)
3-6. MAIN BOARD
Note: The WIRE (FLAT TYPE) (11 CORE) connected with CN507
on the MAIN board is different by the type of the MAIN board.
Replace it for the WIRE (FLAT TYPE) (11 CORE) that is
sure to suit each type when you replace the WIRE (FLAT
TYPE) (11 CORE).
Refer to “NOTE OF REPLACING THE WIRE (FLAT TYPE)
(11 CORE) (CN507 ON THE MAIN BOARD – CN801 ON
THE DISPLAY BOARD)” in servicing notes for the
combination of the WIRE (FLAT TYPE) (11 CORE).
Replace it for the WIRE (FLAT TYPE) (11 CORE) that is
sure to suit each type when you replace the WIRE (FLAT
TYPE) (11 CORE).
Refer to “NOTE OF REPLACING THE WIRE (FLAT TYPE)
(11 CORE) (CN507 ON THE MAIN BOARD – CN801 ON
THE DISPLAY BOARD)” in servicing notes for the
combination of the WIRE (FLAT TYPE) (11 CORE).
HCD-X10
15
3-7. D IN-001 BOARD, D IN-002 BOARD
3-8. P-AMP BOARD
2
four screws
(BVTP3
(BVTP3
×
8)
3
D IN-001 board: US, Canadian model/
D IN-002 board: AEP, UK model
D IN-002 board: AEP, UK model
1
connector
(CN2001: US, Canadian model/)
CH2001: AEP, UK model)
(CN2001: US, Canadian model/)
CH2001: AEP, UK model)
4
wire (flat type) (21 core)
(CN3006)
(CN3006)
1
two screws
(BVTP3
(BVTP3
×
10)
8
seven screws
(BVTP3
(BVTP3
×
6)
9
two screws
2
heat sink (AMP)
3
radiation sheet
(5 ch AMP)
(5 ch AMP)
5
connector
(CN515)
(CN515)
6
connector (CN900)
7
connector
(CN3001)
(CN3001)
0
screw
(BVTP3
(BVTP3
×
8)
qa
P-AMP board
HCD-X10
16
3-9. DVD MECHANISM DECK (CDM85-DVBU102)
7
DVD mechanism deck
(CDM85-DVBU102)
(CDM85-DVBU102)
4
screw
(BVTP3
(BVTP3
×
6)
6
three screws
(BVTP3
(BVTP3
×
8)
1
two rivets
2
two claws
5
bracket (main)
3
cover (CDM)
Click on the first or last page to see other DAV-X10 / HCD-X10 service manuals if exist.