DOWNLOAD Sony DAV-X1 / HCD-X1 Service Manual ↓ Size: 10.68 MB | Pages: 116 in PDF or view online for FREE

13

3

Remove the side panel (L)
in the direction of the arrow.

4

Remove the side panel (R)
in the direction of the arrow.

2

cover (rear)

1

five screws
(BVTP 3 

×

 8)

1

three screws
(BVTP 3 

×

 8)

2

case (AL)

1

screw
(BVTP 3 

×

 8)

1

screw
(BVTP 3 

×

 8)

14

6

four screws
(PTP 3 

×

 8)

7

screw
(BVTP 3 

×

 8)

1

Open the cover dust.

– NOTE WHEN LOADING ASSY PANEL IS REMOVED –

– NOTE WHEN LOADING ASSY PANEL IS INSTALLED –

2

Remove the loading assy panel while pulling it upward
until it is detached completely from the tray.

tray

claw

loading assy panel

loading assy panel

claw

tray

1

Tilt the loading assy panel in the arrow direction
to disengage the claw.
(Tilt continuously a black part of loading assy panel.)

1

Insert the loading assy panel while tilting it in the arrow direction.
(Tilt continuously a black part of loading assy panel.)

2

Install the loading assy panel while pushing it downward until
the claw is locked completely.

2

Slide the chuck cam in the direction
of arrow to releae the chucking.

3

Draw out the loading assy panel
in the direction of the arrow.

5

loading assy panel

4

two claws

9

six claws

8

wire (flat type) (17 core)
(CN505)

q;

front panel section

15

8

three screws
(BVTP 3 

×

 8)

8

screw
(BVTP 3 

×

 8)

8

screw
(BVTP 3 

×

 8)

1

wire (flat type) (9 core)
(AEP, UK, Russian and Singapore models),
wire (flat type) (11 core)
(US, Canadian models)
(CN502)

2

wire (flat type) (19 core)
(CN501)

7

connector
(CN507)

6

two saranet cushions

7

connector
(CN506)

7

connector
(CN5101)

9

MAIN board

3

wire (flat type) (11 core)
(CN504)

4

wire (flat type) (11 core)
(CN503)

5

wire (flat type) (21 core)
(CN506)

3

eight screws
(BVTP 3 

×

 8)

3

two screws
(BVTP 3 

×

 8)

9

two screws
(P 3 

×

 14)

5

4

two screws
(supplied with
CN300)

3

screw
(BVTP 3 

×

 8)

1

wire (flat type) (28 core)
(US, Canadian models)
(CN5401)

2

wire (flat type) (12 core)
(US, Canadian models)
(CN5201)

7

wire (flat type) (17 core)
(AEP, UK and Russian models)
(CN903)

8

connector
(CN450)

6

wire (flat type) (13 core)
(CN902)

qs

back panel section

qs

screw
(BV 3)

qf

sheet (main)

qd

nylon rivet (DIA. 3.5)

q;

two nuts
(N3)

qa

D.C. fan
(M450)

16

3

four screws
(BVTP 3 

×

 8)

5

screw
(BV 3)

8

three screws
(BV 3)

9

DVD mechanism deck
(CDM85-DVBU102)

6

three screws
(BVTP 3 

×

 8)

4

DMB10 board

7

sub chassis

2

wire (flat type) (5 core)
(CN202)

wire (flat type) (24 core)

optical pick-up block

1

Perform work with this wire (flat type) (24 core) connected,
or make a bridge as mentioned above and then disconnect the wire (flat type) (24 core).
(optical pick-up will be destroyed without bridging.)
On the contrary at the installation, connect the wire (flat type) (24 core) first,
and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.

Note: Refer to SERVICING NOTES

“ NOTE OF REPLACING THE DMB10 BOARD”
(page 6), when replacing the DMB10 board.

Be sure to bridge here, and then disconnect the
wire (flat type) (24 core).
(optical pick-up block will be destroyed without bridging.)
On the contrary at the installation, connect the
wire (flat type) (24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire.
(Refer to DISASSEMBLY 3-2. OPTICAL PICK-UP BLOCK (KHM-310CAA))