Sony DAV-SZ1000W / HBD-SZ1000W Service Manual ▷ View online
HBD-SZ1000W
17
2-18. HOW TO BEND FLEXIBLE FLAT CABLE
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
MAIN board
(CN5001)
: Mountain fold
: Valley fold
: Valley fold
23 mm
12 mm
37 mm
18 mm
20 mm
DISPLAY board
(CN501)
DISPLAY board
(CN502)
PANEL board
(CN203)
210 mm
38 mm
13 mm
49 mm
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
47 mm
MAIN board
(CN5005)
S-AIR INC board
(CN203)
33 mm
The lower side
is terminal side.
is terminal side.
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
IOH[LEOHIODWFDEOHFRUHOHQJWKPP5HI1R
The lower side
is terminal side.
is terminal side.
The upper side
is terminal side.
is terminal side.
MAIN board
(CN3008)
IO board
(CN102)
42 mm
38 mm
The lower side
is terminal side.
is terminal side.
8 mm
14 mm
148 mm
The upper side
is terminal side.
is terminal side.
45 mm
95 mm
10 mm
MAIN board
(CN1502)
CDM85 (MB) assy
62 mm
195 mm
13 mm
The lower side
is terminal side.
is terminal side.
MAIN board
(CN1502)
optical pick-up
(KHM-313CAA)
The lower side
is terminal side.
is terminal side.
HBD-SZ1000W
18
SECTION 3
TEST MODE
Note: Incorrect operations may be performed if the test mode is not
entered properly.
In this case, press the [
?/1] button to turn the power off, and
retry to enter the test mode.
COLD RESET
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customers.
Procedure:
1. Press the [
The cold reset clears all data including preset data stored in the
RAM to initial conditions. Execute this mode when returning the
set to the customers.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press three buttons [
N
], [FUNCTION] and [
?/1
] simultane-
ously.
3. When this button is operated, display as “RESET” for a while
and all of the settings are reset.
PANEL TEST MODE
This mode is used to check the software version, FL and KEY.
This mode is used to check the software version, FL and KEY.
1. Display Test Mode
Procedure:
1. Press the [
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press three buttons [
x
], [VOLUME +] and the [
N
] buttons
simultaneously.
3. When the display test mode is activated, all segments are
turned on. When the mode in, “REC TO USB” is turn off.
Releasing method:
Press three buttons [
Press three buttons [
x
], [VOLUME +] and the [
N
] buttons si-
multaneously.
2. Version Test Mode
Procedure:
1. When the display test mode is activated, press the [FUNC-
Procedure:
1. When the display test mode is activated, press the [FUNC-
TION] button and the model name is displayed, the version
test mode is activated.
test mode is activated.
2. Whenever the [FUNCTION] button is pressed, the display
changes in the following order.
DX (Model name)
t (Destination) t MC Version
3. Press the [REC TO USB] button when the MC version is on
display. The date of software production is displayed.
4. Press the [REC TO USB] button again and the version is dis-
played.
Releasing method:
Press three buttons [
Press three buttons [
x
], [VOLUME +] and the [
N
] buttons si-
multaneously.
3. FL Pattern Test Mode
Procedure:
1. When the display test mode is activated, press the [
Procedure:
1. When the display test mode is activated, press the [
Z
] button,
to select the FL pattern test mode. When the FL pattern test
mode, half segments of FL display and “REC TO USB” are
turn on.
mode, half segments of FL display and “REC TO USB” are
turn on.
2. Press the [
Z
] button, half segments of fl uorescent indicator
tube and “REC TO USB” are turned off.
Releasing method:
Press three buttons [
Press three buttons [
x
], [VOLUME +] and the [
N
] buttons si-
multaneously.
4. Key Test Mode
Procedure:
1. When the display test mode is activated, press the [
Procedure:
1. When the display test mode is activated, press the [
?/1
] but-
ton, to select the key test mode.
2. To enter the KEY test mode, the fl uorescent indicator displays
“K0”. Each time an another button is pressed, “KEY” value
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K8”
is displayed.
increases. However, once a button is pressed, it is no longer
taken into account. When all keys are pressed correctly, “K8”
is displayed.
Releasing method:
Press three buttons [
Press three buttons [
x
], [VOLUME +] and the [
N
] buttons si-
multaneously.
DISC TRAY LOCK
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Procedure:
1. Press the [
The disc tray lock function for the antitheft of an demonstration
disc in the store is equipped.
Procedure:
1. Press the [
?/1
] button to turn the set on.
2. Press the [FUNCTION] button to set DVD function.
3. Insert a disc.
4. Press
3. Insert a disc.
4. Press
the
[
x
] button and the [
Z
] button simultaneously for fi ve
seconds.
5. The message “LOCKED” is displayed and the tray is locked.
Releasing method:
1. Press
Releasing method:
1. Press
the
[
x
] button and the [
Z
] button simultaneously for fi ve
seconds again.
2. The message “UNLOCKED” is displayed and the tray is un-
locked.
Note: When “LOCKED” is displayed, the tray lock is not released by
turning power on/off with the [
?/1] button.
VERSION DISPLAY
The STR and DVD microprocessor versions are displayed.
Procedure:
1. Press the [
The STR and DVD microprocessor versions are displayed.
Procedure:
1. Press the [
?/1
] button to turn the set on.
2. Press two buttons [
N
] and [
?/1
] simultaneously for three sec-
onds. SC version display is presented.
3. Pressing the [FUNCTION] button presents a DV version dis-
play. Pressing the [FUNCTION] button again returns to the SC
version display.
version display.
Releasing method:
Press any button other than the [FUNCTION] button.
Press any button other than the [FUNCTION] button.
DVD VERSION DISPLAY
The DVD versions is displayed.
Procedure:
1. In the standby status, press two buttons [
The DVD versions is displayed.
Procedure:
1. In the standby status, press two buttons [
N
] and [
?/1
] simul-
taneously.
2. The DVD version is displayed.
Releasing method:
Press the [
Releasing method:
Press the [
\/1] button.
HBD-SZ1000W
19
PRODUCT OUT
This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the STR
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
This mode moves the optical pick-up to the position durable to
vibration and clears all data including preset data stored in the STR
RAM to initial conditions. Use this mode when returning the set to
the customer after repair.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Press the [FUNCTION] button to set the function “DVD/CD”.
3. Remove all discs, and then press three buttons [
3. Remove all discs, and then press three buttons [
x
], [
Z
] and
[VOLUME+] simultaneously.
4. Displayed to message “SERVICE” on the fl uorescent indica-
tor tube when pressing in turn the [4]
t [DVD MENU] t
[CLEAR] buttons on the remote commander.
5. After the “STANDBY” blinking display fi nishes, the message
“LOCKED”
h “UNPLUG” is displayed on the fl uorescent
indicator tube disconnect the AC power plug, then the product
out mode is set.
out mode is set.
The STR RAM initialization is executed upon a next power-on
after the power is turned off.
after the power is turned off.
PROTECTION FACTOR (SD DETECTION/DC DETEC-
TION/TSD DETECTION) IDENTIFICATION TEST MODE
When an error is detected, the FL tube alternately displays
“PROTECT”
TION/TSD DETECTION) IDENTIFICATION TEST MODE
When an error is detected, the FL tube alternately displays
“PROTECT”
h “PUSH PWR”.
r Press the [
?/1
] button.
* Buttons other than the [
?/1
] button are invalid.
“STANDBY” blinks three times on the FL tube.
r
The protection release state (POWER OFF) is established.
(No FL tube display)
(No FL tube display)
r Press the [
?/1
] button two times.
The power to the system turns on, and the normal operation is
established. (Restore)
established. (Restore)
During the protection state:
1. If the AC plug is connected or disconnected during the protec-
1. If the AC plug is connected or disconnected during the protec-
tion state, the protection state is released, and the normal op-
eration is established. (The protection state is not maintained.)
eration is established. (The protection state is not maintained.)
2. The protection factor is displayed by pressing the [RETURN]
t [3] t [2] t [0] t [0] t [ANGLE] buttons of the re-
mote commander.
(during the “PROTECT”
h “PUSH PWR” display).
k When SD is detected: Repeats
“SD
ERR”
h “PROTECT”.
k When DC is detected: Repeats
“DC
ERR”
h “PROTECT”.
k When TSD is detected: Repeats
“TMP
ERR”
h “PROTECT”.
PL: SD detection
When the “L” output from the SD (shutdown) port on the
S-MASTER POWER Driver Shutdown and voltage descent
(15V or less) of 30V power supply (PVDD) are detected.
S-MASTER POWER Driver Shutdown and voltage descent
(15V or less) of 30V power supply (PVDD) are detected.
DC
detection
When the “L” output from the power/speaker error detection
circuit (DC detection port) is detected for two seconds con-
tinually, the power system other than that of the FL tube is
turned off, and the protection state is established.
circuit (DC detection port) is detected for two seconds con-
tinually, the power system other than that of the FL tube is
turned off, and the protection state is established.
TSD
detection
When the “L” output from the thermal shutdown port
(TSDM) on the motor driver is detected.
(TSDM) on the motor driver is detected.
Releasing method:
Press the buttons on the remote commander in the order given be-
low.
[RETURN]
Press the buttons on the remote commander in the order given be-
low.
[RETURN]
t [3] t [2] t [0] t [0] t [ANGLE]
COLOR SYSTEM CHANGE
Color system change to video signal format (NTSC/PAL).
Procedure:
In Standby mode, press two buttons [FUNCTION] and [
Color system change to video signal format (NTSC/PAL).
Procedure:
In Standby mode, press two buttons [FUNCTION] and [
?/1
] si-
multaneously, and the display of fl uorescent indicator tube changes
to “PAL” or “NTSC”.
to “PAL” or “NTSC”.
D. C. A. C. TEST MODE
The D. C. A. C. (Digital Cinema Auto Calibration) test is executed.
Procedure:
1. Press the [
The D. C. A. C. (Digital Cinema Auto Calibration) test is executed.
Procedure:
1. Press the [
?/1
] button to turn the power on.
2. Insert ECM-AC2 supplied as an accessory into the [AUDIO
IN 4/A. CAL MIC] jack.
3. Press three buttons [
x
], [
Z
] and [REC TO USB] simultane-
ously.
4. Confi rm that the following are shown on the fl uorescent indi-
cator tube.
1 Microphone inserted/non-inserted detection display and
the STEREO/MONO detection display.
2 Presence of digital audio input to the μ-com (OK: input,
NG: no input).
3 The value of microphone input to the μ-com(shown
“255h”).
* * * * * * * *
1
1 “NON”
: Not detected
“ST” :
STEREO
“MN” :
MONO
2 “OK” :
Input
“NG”
: No input
3 0 to 255 (Changes in real time)
2
3
Releasing method:
Press three buttons [
Press three buttons [
x
], [
Z
] and [REC TO USB] simultaneously.
HBD-SZ1000W
20
2. Select “2. Drive Manual Operation” by pressing the [2] button
on the remote commander. The screen will appear as shown.
Drive Manual Operation
1. Servo Control
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time adjust
0. Return to Top Menu
2. Track/Layer Jump
3. Manual Adjustment
4. Tray Aging Mode
5. MIRR time adjust
0. Return to Top Menu
3. Select “3. Manual Adjustment” by pressing the [3] button on
the remote commander. The screen will appear as shown.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
O o Change Value
[RETURN] Return to previous menu
4. Select “6. IOP” by pressing the [6] button on the remote com-
mander.
5. Wait until a hexadecimal number appear.
Manual Adjust
1. Track Balance Adjust:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. 4D:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
2. Track Gain Adjust:
3. Focus Balance Adjust:
4. Focus Gain Adjust:
5. Eq Boost Adjust:
6. Iop. 4D:
7. TRV. Level:
8. S curve(FE) Level:
9. RFL(PI) Level:
0. MIRR Time:
[RETURN] Return to previous menu
O o Change Value
6. Convert each data from hexadecimal to decimal using conver-
sion table.
7. Please
fi nd the label on the rear of the BU (Base Unit).
The default IOP value is written in the label.
8. Subtract between these two values.
9. If the remainder is smaller than 93 (decimal), then it is OK.
However if the value is higher than 93, then the BU is defec-
tive and need to be change.
tive and need to be change.
10. Press the [RETURN] button on the remote commander to re-
turn back to previous menu.
11. Press the [0] button on the remote commander to return to Top
Menu.
DVD SERVICE MODE
The IOP measurement allows you to make diagnosis and adjust-
ment simply by using the remote commander and monitor TV. The
instructions, diagnosis results, etc. are given on the on-screen dis-
play (OSD).
Be sure to execute the IOP measurement when a BU (Base Unit)
is replaced.
The IOP measurement allows you to make diagnosis and adjust-
ment simply by using the remote commander and monitor TV. The
instructions, diagnosis results, etc. are given on the on-screen dis-
play (OSD).
Be sure to execute the IOP measurement when a BU (Base Unit)
is replaced.
1. How To Enter Test Mode
1. Press the [
1. Press the [
?/1
] button to turn the power on.
2. Press three buttons [
x
], [VOLUME +] and the [
Z
] buttons
simultaneously.
3. The Test Mode starts, displayed “SERVICE” on this model
display then the menu shown below will be displayed on the
TV screen.
TV screen.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
Model Name
IF-con
IF-con
: Ver. XX.XX (XXXX)
Syscon
: Ver. X.XXX
: XXXX
4. The menu above is the Remocon Diagnosis Menu screen
which consists of fi ve main functions. At the bottom of the
menu screen, the model name and IF-con version.
menu screen, the model name and IF-con version.
2. Releasing Test Mode
Press the [
Press the [
?/1
] button on the remote commander.
3. Executing IOP Measurement
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
In order to execute IOP measurement, the following standard pro-
cedures must be followed.
1. In power on, press three buttons [
x
], [VOLUME +] and the
[
Z
] buttons simultaneously.
Remocon Diagnosis Menu
0. External Chip Check
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
1. Servo Parameter Check
2. Drive Manual Operation
3. Emergency History
4. Version Information
5. USB Test Mode Setting
Model Name
IF-con
IF-con
: Ver. XX.XX (XXXX)
Syscon
: Ver. X.XXX
: XXXX
Click on the first or last page to see other DAV-SZ1000W / HBD-SZ1000W service manuals if exist.