Sony DAV-IS50 / HCD-IS50 Service Manual ▷ View online
HCD-IS50
13
3-4. PANEL (SIDE-L/R)
ASSY
screws
(BVTP3
(BVTP3
s 8)
panel (side-R) assy
screws
(BVTP3
(BVTP3
s 8)
panel (side-L) assy
three screws
(BVTP3
(BVTP3
s 8)
cover (rear) assy
– back view –
3-5. PANEL (TOP) BLOCK, SHIELD PLATE (TOP)
screws
(BVTP3
(BVTP3
s 8)
screws
(BVTP3
(BVTP3
s 8)
three screws
(BVTP3
(BVTP3
s 8)
three screws
(BVTP3
(BVTP3
s 8)
two screws
(BVTP3
(BVTP3
s 8)
two screws
(BVTP3
(BVTP3
s 8)
shield plate (top)
wire (flat type) (11 core)
(CN108)
(CN108)
panel (top) block
– back view –
HCD-IS50
14
3-7. IO BOARD
3-6. MAIN BOARD
RE four screws
(BVTP3
(BVTP3
s 8)
wire (flat type)
(CN102) (9 core: except AEP, UK, Russian models)/
(CN101) (11 core: AEP, UK, Russian models)
wire (flat type) (21 core)
(CN103)
(CN103)
screw
(BVTP3
(BVTP3
s 8)
insulating sheet
(motor)
(motor)
US, Canadian
connector (CN107)
connector (CN111)
two screws
(BVTP3
(BVTP3
s 8)
shield plate (side-L)
wire (flat type) (19 core)
(CN105)
(CN105)
wire (flat type) (9 core)
(CN110)
(CN110)
RT wire (flat type) (13 core)
(CN106)
(CN106)
RG MAIN board
RB wire (flat type) (11 core)
(CN109)
(CN109)
– back view –
wire (flat type) (21 core)
(CN103)
(CN103)
two screws
(BVTP3
(BVTP3
s 8)
five screws
(BVTP3
(BVTP3
s 8)
screw
(BVTT3
(BVTT3
s 8)
screw
(BVTP3
(BVTP3
s 8)
back panel (HCD)
IO board
– back view –
HCD-IS50
15
3-8. REG BOARD
connector (CN702)
connector (CN710)
connector (CN708)
RB REG board
connector (CN111)
two screws
(BVTP3
(BVTP3
s 8)
– back view –
screw
(BVTP3
(BVTP3
s 8)
insulating sheet
(motor)
(motor)
US, Canadian
two screws
(BVTP3
(BVTP3
s 8)
shield plate (side-L)
3-9. DMB-FIT BOARD
R three screws
(BVTP3
(BVTP3
s 8)
connector (CN201)
DMB-FIT board
connector (CN105)
connector (CN601)
five screws
(BVTP3
(BVTP3
s 8)
wire (flat type) (7 core)
(CN202)
(CN202)
wire (flat type) (24 core)
(CN101)
(CN101)
Perform work with this wire (flat type) (24 core) connected, or make a bridge as mentioned above and then disconnect the wire
(flat type) (24 core). (Optical pick-up will be destroyed without bridging.) On the contrary at the installation, connect the wire (flat type)
(24 core) first, and then remove the bridge.
(flat type) (24 core). (Optical pick-up will be destroyed without bridging.) On the contrary at the installation, connect the wire (flat type)
(24 core) first, and then remove the bridge.
Note: For a soldering iron, use the one with a ground wire. (Refer to DISASSEMBLY 3-2. OPTICAL PICK-UP BLOCK (KHM-313CAB))
PRECAUTION WHEN REMOVING WIRE (FLAT TYPE) (24 CORE)
– back view –
wire (flat type) (13 core)
(CN109)
(CN109)
wire (flat type) (19 core)
(CN4301)
(CN4301)
HCD-IS50
16
3-10. FRONT PANEL BLOCK
screw
(BVTP3
(BVTP3
s 8)
two screws
(BVTP3
(BVTP3
s 8)
three screws
(BVTP3
(BVTP3
s 8)
shield plate (side-L)
wire (flat type) (11 core)
(CN109)
(CN109)
front panel block
insulating sheet
(motor)
(motor)
US, Canadian
3-11. MECHANISM DECK SECTION (CDM86A-DVBU101)
RM mechanism deck section
(CDM86A-DVBU101)
(CDM86A-DVBU101)
shield plate (side-R)
two screws
(BVTP3
(BVTP3
s 8)
two screws (BVTP3 s 8)
bracket (SYS)
two screws
(BVTT2.6
(BVTT2.6
s 6)
screw
(BVTP3
(BVTP3
s 8)
tuner (FM/AM)
RB two screws
(BVTP2.6)
(BVTP2.6)
RT two ground
plates
plates
(panel)
RE bracket (CDM)
system cable
RG three screws
(BVTP3
(BVTP3
s 8)
RH shield plate (front)
RI two screws
(BVTP3
(BVTP3
s 8)
RK sub chassis (HCD)
RL screw
(BVTP3
(BVTP3
s 8)
wire (flat type)
(9 core: except AEP, UK, Russian models)/
(11 core: AEP, UK, Russian models)
Click on the first or last page to see other DAV-IS50 / HCD-IS50 service manuals if exist.