Sony DAV-IS10 / SA-WSIS10 / SS-IS10 Service Manual ▷ View online
5
SA-WSIS10/SS-IS10
POWER board
SPEAKER board
clamp
Clamp the cable inside.
clamp
clamp
DSP board
AMP board
clamp (US, Canadian)
Dress the cable through the gap
of mounted parts as shown.
of mounted parts as shown.
HARNESS SETTING (SA-WSIS10)
C903
C913
C924
C930
R908
EB905
C910
C963
– POWER Board (Component side) –
C964
R927
screw
C963
C964
C903
C913
R908
C924
C910
C930
R927
• Fix between C963 and C964 by the bond.
• Fix between C910 and C930 by the bond.
Note: Fix so that the distance of C910 and
EB905 may become 8 mm or more.
• Fix between C924 and R927 by the bond.
Note: Fix so that the distance of C924 and
the screw may become 8 mm or more.
• Bend C913 to C903 side, and fix between
C913 and the POWER board by the bond.
Note: Fix so that the distance of C913 and
Note: Fix so that the distance of C913 and
R908 may become 8 mm or more.
8 mm
8 mm
8 mm
EB905
Ver. 1.3
FIXING ELECTRICAL PARTS WITH A BOARD (SA-WSIS10)
If the POWER board is replaced, or if the target parts listed below were replaced, the parts must be fixed to the board using the specified bond.
• Object boards
Board name
Part No.
POWER
A-1249-813-A (US, Canadian and Taiwan models)
A-1249-842-A (AEP, Russian, UK, Saudi Arabia, Singapore, Argentina, Thai, Australian and Chinese models)
A-1249-854-A (Latin America models except Argentina)
• Object parts
Board name
Ref. No.
POWER
C903, C910, C913, C924, C930, C963, C964, R927
• Use bond
BOND, SONY (SC608LV) (Part No. 7-432-912-48)
• Bond installation position
6
SA-WSIS10/SS-IS10
SECTION 2
GENERAL
This section is extracted from
instruction manual.
instruction manual.
Subwoofer
Ventilation slots
SYSTEM CONTROL jack
SPEAKER jacks
SYSTEM CONTROL
ONLY FOR HCD-IS10
SPEAKER
ONLY FOR SS-IS10
CENTER
SUR L
SUR R
FRONT L
FRONT R
Bottom of the subwoofer
SA-WSIS10/SS-IS10
7
6
4
two caps
5
two screws
(B4
(B4
×
14)
7
AMP block
1
two screws
(B4
(B4
×
14)
2
fan cover
3
connector
(CN002)
(CN002)
Note:
Follow the disassembly procedure in the numerical order given.
3-2. AMP BLOCK
Note1: Please lay the set and work.
Note2: It is an illustration to which parts are
Note2: It is an illustration to which parts are
removed from the back bottom side.
• SA-WSIS10 can be disassembled in the order shown below.
3-1. DISASSEMBLY FLOW (SA-WSIS10)
SECTION 3
DISASSEMBLY
SET
3-2. AMP BLOCK
(Page 7)
3-3. AMP BOARD
(Page 8)
3-4. DSP BOARD
(Page 9)
3-5. POWER BOARD
(Page 9)
3-6. LOUDSPEAKER (16 cm)
(SUB WOOFER) (SP001)
(Page 9)
(Page 9)
3-7. LOUDSPEAKER (12 cm)
(MIDDLE) (SP002)
(Page 9)
(Page 9)
SA-WSIS10/SS-IS10
8
3-3. AMP BOARD
4
heatsink (AMP-WS)
5
wire (flat type) (23 core)
(CN201)
(CN201)
6
connector (CN202)
7
connector (CN218)
9
connector (CN561)
0
connector (CN521)
qa
connector (CN562)
8
three connectors
(CN531, CN541, CN551)
(CN531, CN541, CN551)
3
three screws
(BVTP3
(BVTP3
×
12)
qs
three screws
(BVTP3
(BVTP3
×
8)
qs
screw
(BVTP3
(BVTP3
×
8)
qd
radiation sheet (AMP)
qf
two radiation sheets
1
twenty two screws
(BV3)
(BV3)
2
panel back
qg
AMP board
Click on the first or last page to see other DAV-IS10 / SA-WSIS10 / SS-IS10 service manuals if exist.