Sony DAV-DZ530 / DAV-DZ630 / HCD-DZ530 / HCD-DZ630 Service Manual ▷ View online
13
HCD-DZ530/DZ630
3-2. CASE (DS), FRONT PANEL ASSY
Note:
Follow the disassembly procedure in the numerical order given.
q;
wire (flat type)
21core (CN502)
2
The lever is moved in the direction
of the arrow with the thin rod.
1
seal
harness
3
rib
4
loading panel
5
two screws
(CASE3 TP2)
(CASE3 TP2)
8
case (DS)
qj
front panel assy
qd
four screws
(+BV 3
(+BV 3
×
6)
qg
two claws
qh
two
claws
claws
6
two screws
(CASE3 TP2)
7
five screws
(+BVTP 3
×
8)
9
unweaved
cloth
cloth
rib
rib
notch
harness
rib
lead pin
rib
rib
groove
Route the harness as shown below.
Route the harness as shown below.
qa
connector 4P(CN302)
qf
two screws
(+BVTP
2.6
×
10)
qs
connector 4P (CN3001)
14
HCD-DZ530/DZ630
3-3. FL BOARD
front panel
PRECAUTION DURING THE RETAINER (DS) INSTALLATION
(2) Route the harness as shown below.
(3) Route the harness as shown below.
(1) Assemble seven claws securely.
4
shield plate (FR)
8
FL board
3
five screws
(+BVTP 2.6
(+BVTP 2.6
×
10)
5
two screws
(+BVTP 2.6
(+BVTP 2.6
×
10)
1
two
rivets
rivets
6
wire (flat type)
13core (CN805)
7
wire (flat type)
21core (CN801)
2
retainer (DS)
retainer (DS)
harness
rivet
rivet
hole
retainer (DS)
harness
wire (flat type)
groove
groove
retainer (DS)
hole
shield plate (FR)
FL board
JACK
board
board
CN806
CN805
wire (flat type) 13core
Route the wire
(flat type) 13core
as shown in the figure.
(flat type) 13core
as shown in the figure.
15
HCD-DZ530/DZ630
3-5. DMPORT BOARD,TUNER (FM/AM)
3-4. JACK BOARD, P-SW BOARD
Route the harness as shown below.
JACK board
JACK board
JACK board
JACK board
(NG)
(OK)
Route the harness as shown below.
(NG)
(OK)
1
knob (vol)
2
nut
qa
JACK board
4
button (base)
5
wire (flat type)
13core (CN806)
13core (CN806)
8
Remove the
solderings.
9
harness
3
four screws
(+BVTP
(+BVTP
2.6
×
10)
6
screw
(+BVTP
2.6
×
10)
7
button (base)
q;
P-SW board
2
wire (flat type) 11core
4
connector 3p (CN203)
5
wire (flat type) 9core (CN201)
6
screw
(+BV
(+BV
3
×
6)
1
two screws
(+BVTT
(+BVTT
2.6
×
6)
7
DMPORT board
3
tuner (FM/AM)
16
HCD-DZ530/DZ630
3-6. IO-SCART BOARD
3-7. POWER BOARD
6
three screws
(+BV
(+BV
3
×
6)
9
IO-SCART board
7
wire (flat type)
9core (CN301)
9core (CN301)
2
wire (flat type)
21core (CN308)
21core (CN308)
1
wire (flat type)
13core (CN304)
13core (CN304)
3
wire (flat type)
5core (CN307)
5core (CN307)
8
wire (flat type)
11core (CN305)
11core (CN305)
4
connector
4p (CN302)
4p (CN302)
5
four screws
(+BVTP
(+BVTP
3
×
8)
1
connector
4p (CN3002)
4p (CN3002)
3
connector
12p (CN906)
12p (CN906)
4
connector
3p (CN907)
3p (CN907)
2
connector
2p (CN901)
2p (CN901)
6
eight screws
(+PWH
(+PWH
3
×
8)
5
screw
(+BV
(+BV
3
×
6)
q;
POWER board
9
cover (PWB)
8
Remove the two claws
in the direction of the
arrow
in the direction of the
arrow
B
.
7
Remove the POWER board
and the cover (PWB) in the
direction of the arrow
and the cover (PWB) in the
direction of the arrow
A
.
heatsink (AMP)
harness
screw
lead pin
Clamp the harnesses with a
lead pin or a similar tool so
that they do not touch this
screw and the heatsink (AMP).
lead pin or a similar tool so
that they do not touch this
screw and the heatsink (AMP).
Attach the heat radiation sheets
on the chassis, and then install
the POWER board.
on the chassis, and then install
the POWER board.
Attention at assembling
POWER board.
POWER board.
Because of Prevention of
damage caused by creep of
radiation sheets, outfit a power
board with the set after fitting
the cover (PWB) on the POWER
board.
damage caused by creep of
radiation sheets, outfit a power
board with the set after fitting
the cover (PWB) on the POWER
board.
radiation sheets
A
B
Click on the first or last page to see other DAV-DZ530 / DAV-DZ630 / HCD-DZ530 / HCD-DZ630 service manuals if exist.